HOMCOM CHILDREN'S ELECTRIC RIDE-ON A User manual

CHILDREN’S ELECTRIC RIDE-ON
Owner’s Manual
with Assembly Instructions
Styles and colours may vary.
Made in China.
The owner’s manual contains important safety information as well as assembly, use and
maintenance instructions.
The Ride-on Car must be assembled by an adult who has read and understands the
instructions in this manual.
Keep the package away from children and dispose of properly before use.
Keep this manual for future reference.
TYPE A
TYPE C
TYPE B
TYPE D

On the purchase of your new Ride-On.
This ride-on car will provide your child with many miles of riding of
enjoyment. To help assure you and your rider a safe ride we ask you to please
read this manual carefully, and keep it for future reference.
Follow the recommendations in this manual, they are designed to improve the
safety and operation of your ride-on car and it’s rider.
Battery
Charger
6V4Ah *1 or 6V7Ah * 1 6V4Ah*2 or 6V7Ah*2
6V1000mA 12V1000mA
Suitable age:
Load Capacity:
Speed:
Size of car:
Power way:
Charge time:
37~96 Months
Under 30 kgs
2.5 km/h 2.5~5km/h
TYPE A: 148x61x64 CM / TYPE B: 141x61x64 CM
TYPE C: 117x61x64 CM / TYPE D: 106x61x64 CM
Charging type
8 ~ 12 hours
1WD 2WD
About Your New Ride-On │ 1
VER: SMS-JS328-EN-190111

2
2
8
2
4
4
2
3
2
A
B
C
D
E
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
1
1
10
1
2
2
3
4
1
1
1
1
1
1
1
1
1
1
1
3
PART
NO.
REMARKS
PART NAME
Q’ty (pcs)
Gear box
Rear driving wheel
Ø12 washer
Steering plate
Inner bushing
Front wheel
Outer bushing
Ø10 Locknut
Vehicle body
Steering column
Front axle
Rear axle
Seat
M5x40 machines screw
Steering wheel
Ø5 nut
Windshield
Rear exhaust
Charger
Ø4x16 screw
Hubcap
Split pin
Ø10 washer
Spanner
Placed on the steering wheel
Placed on the steering wheel
1pc labeled “L”, and 1pc labeld “R”
1 pcs for spare
1 pcs for spare
1WD 2WD
2WD
Parts List of vehicle body │ 2
Assembly package

19
E
1
2
6
7D
C
8
B
8
9
10
11
12
13
14 15
17
5
18
16
4
3
3
3
3
A
B
NOTE: Some parts shown are assembled on both sides of vehicle
Parts Diagram of Vehicle Body │ 3
Vehicle body of type C

112
2
34
5
6
7
89
10 11
Parts Diagram of Bucket │ 4
TYPE A
The follow illustration is only for TYPE A.
1. Ø10 locknut *2
2. Inner bushing *2
3. Ø12 rod *1
4. Ø4x16 screw *2
5. Boom (right) *1
6. Boom (left) *1
7. Boom linkage *1
8. Bucket tip *2
9. Bucket cover *2
10. Lock tie *2
11. Bucket *1
12. Ø12 washer *2
Longest: Rear axle
Shorter: Front axle
Shortest: Ø12 rod

112
34
56
8
9
11
10
7
2
Parts Diagram of Thumb Bucket │ 5
TYPE B
The follow illustration is only for TYPE B.
1. Ø10 locknut *2
2. Inner bushing *2
3. Ø12 rod *1
4. Ø4x16 screw *2
5. Boom (right) *1
6. Boom (left) *1
7. Boom linkage *1
8. Bucket tip *2
9. Bucket cover *2
10. Lock tie *2
11. Thumb bucket *1
12. Ø12 washer *2
Longest: Rear axle
Shorter: Front axle
Shortest: Ø12 rod

1
2
6
3
4
5
Parts Diagram of Tipper │ 6
TYPE C
The follow illustration is only for TYPE C.
1. Tipper lock *1
2. Tipper *1
3. Ø8 rod *1
4. Ø8 washer *2
5. Ø8 locknut *2
6. Vehicle body of Type C *1
Longest: Rear axle
Shorter: Front axle
Shortest: Ø8 rod

FOR THE SAFETY OF YOUR CHILD, PLEASE READ ALL WARNINGS AND
ASSEMBLY/USE INSTRUCTIONS. KEEP THIS GUIDE FOR FUTURE REFERENCE.
• ADULT ASSEMBLY REQUIRED. The product contains small parts, which are for
adult assembly only. Keep children away when assembling.
• Always remove protective material and poly bags and dispose before assembly.
Before You Begin Assembly │ 7
WARNING!
FOR THE SAFETY OF YOUR CHILD, PLEASE READ ALL WARNINGS AND
ASSEMBLY/USE INSTRUCTIONS. KEEP THIS GUIDE FOR FUTURE REFERENCE.
• ADULT ASSEMBLY REQUIRED. The product contains small parts, which are for
adult assembly only. Keep children away when assembling.
• Always remove protective material and poly bags and dispose before assembly.
• Make sure that the power switch is turned “OFF” before assembling the ride-
on.
• Before first time use, charge the battery for at least 4 to 6 hours.
• Assembly tools required:
WARNING!
Screwdriver
(not included)
Long nose pliers
(not included)
Spanner

2
1
1
Attach the Rear Axle │ 8
Remove all the parts from the rear axle.
1. Insert the rear alxe into the hole on the vehicle body.
Remove all the parts from the rear axle.
1. Slide a Ø12 washer onto the rear axle from the longer end.
2. Insert the rear axle with a Ø12 washer into the hole on the
vehicle body from the right hand side.
Rear alxe with a Ø12 washer
1WD
2WD

1
3
2
4
5
11
67
8
910
11
x2
2
1,2. Slide the gear box onto the rear axle (Left Side). Plug the connector on
motor into the connecotr on the vehicle body.
3. Slide the rear driving wheel onto the rear axle. And keep the driving wheel
match up with the gear box.
4. Slide the Ø12 washer onto the rear axle.
5. Tighten a locknut to the end of the rear axle with a spanner.
6. Slide the washer onto the axle from the right side.
7. Slide the location bushing onto the rear axle.
8. Slide the rear normal wheel onto the rear axle.
9. Slide the Ø12 washer onto the rear axle.
10. Tight a locknut to the end of the rear axle with a spanner. HINT: An extra
spanner has been provided to hold the locknut on the other side of the
rear alxe while tightening the locknut on the other side.
11. Fit the hubcaps to the wheels on both sides.
1WD Attach the Rear Wheels │ 9
Rear axle
Rear wheels are more bigger
than front wheels
Rear normal wheel
Rear driving wheel
Tools required: Spanner
HINT: If your vehicle is Two Wheels Driving Type, see the next page please.

4
5
6
89
10
11
x2
4
5
1
3
11
7
2
1,2. Slide the gear box onto the rear axle (Left Side). “R” labeled gear box should be fit to
the “R” side of vehicle body; “L” labeled gear box should be fit to “L” side of vehicle
body. Plug the connector on motor to the connecotr on the vehicle body.
3. Slide the rear driving wheel onto the rear axle. And keep the rear driving wheel match
up with the gear box.
4. Slide the Ø12 washer onto the rear axle.
5. Tight a Ø10 locknut to the end of the rear axle with a spanner.
Rear axle
Tools required: Spanner
2WD Attach the Rear Wheels │ 10
6-11: Repeat for the other driving wheel.
Rear wheels are more bigger
than front wheels
Rear driving wheel
Rear driving wheel
HINT: An extra spanner has been provided to hold the locknut on the other
side of the rear alxe while tightening the locknut on the other side.

1
2
3
4
1,2. Turn the steering plate until it can be fit to the vehicle body.
3. Turn the steering plate to line up the holes in the steering plate and the holes in
the vehicle body.
4. Fit the front axle to the vehicle body.
Attach the Steering Plate │ 11

1
2
3
4
5
6
7
8
Front axle
Tools required: Spanner
Remove all the parts from the front axle.
1. Slide a Ø12 washer onto the front axle.
2. Slide the inner bushing onto the front axle.
3. Slide a Ø12 washer onto the front axle.
4. Slide a outer bushing (ring end first) onto the front axle.
5. Slide the front wheel onto the front axle. And keep tit match up with the outer
bushing.
6. Slide a Ø12 washer onto the front axle.
7. Tighten a locknut to the end of the front axle with a spanner.
HINT: An extra spanner has been provided to hold the locknut on the other
side of the rear alxe while tightening the locknut on the other side.
8. “Snap” the hubcap to the wheel cover.
Repeat for the other front wheel.
GAP
After assembling any wheel to the axles, please check the gap
between the screw thread and the collapsible (refer to below
picture), if the gap is too big, please add two or three washers inside
the wheel, But after tightening the nut outside the wheel, please turn
the wheel by your finger to check if the wheel can run smoothly, this
is very important, because if the wheel can run smoothly, it is ok, but
if the nut press the wheel and the wheel can’t run smoothly, the
motor will be broken easily! Then you need to decrease one or two
washers to make sure the wheel can run smoothly!
Attach the Front Wheels │ 12
Front wheel, more smaller than
Rear wheel.

4
5
3
4
1
2
Steering
column
Steering
plate
1. Turn the vehicle body on its side, insert the steering column through the groove A on
the steering plate, the hole in the vehicle body and out through the hole on the dash.
2. Insert the bent end of steering column through the groove B on the front axle linkage.
3. Fit a Ø10 washer onto the steering column.
4. Insert a split pin into the hole in the steering column, bend the ends of split pin back
using a long nose pliers.
Attach the Steering Column │ 13
groove A
groove A
groove B

23
1
4
4
End of the steering column
Attach the Steering Wheel │ 14
● Turn the vehicle body over. Remove the M5x40 machine screw and Ø5 nut from the
steering wheel with a screwdriver.
1. Place the steering wheel over the steering column, protruding from the middle of the
steering wheel base.
2. Align the holes on each side of steering wheel with the holes at the end of the
steering column.
3. Fasten a nut on the opposite end of the screw to secure the steering wheel to the
steering column.
4. Insert the tabs on the windshield to the slots in the vehicle body, and push until you
hear it “click” into place.

1
Connect the Powr Supply │ 15
1. Plug the red fuse connector into the terminal on battery.
Fuse box
BATTERY

1
1
3
2
Attach Seat & Rear Exhaust │ 16
1. Fit the tabs at back of the
seat to the holes on the
vehicle body.
2. Insert two Ø4x16 screws
and tighten with a
screwdriver.
3. Insert the tabs on the rear exhaust
into the holes on the vehicle body,
and push until you hear it “click” into
place.
TYPE D COMPLETED!

2
1
4
3
Assemble the Bucket-1 │ 17
The follow steps are only for TYPE A.
1. Fit the bucket into boom (right),
2. Fit the bucket cover to the bucket,
3. Fit the bucket lock (ring end) against to the bucket,
4. Turn the bucket until line up the holes in the boom (right), the holes in the
bucket lock with the hole in the bucket
to be continued...
TYPE A

6
5
Assemble the Bucket-2 │ 18
The follow steps are only for TYPE A.
5. Insert the bucket tip through the hole
in holes in the boom (right), the holes
in the bucket lock, the hole in the
bucket and out the hole in the boom
(right),
6. Bend the bucket lock (opening end) ,
and fit it into the grooved area in the
bucket tip.
Repeat for the other boom.
to be continued...
Bucket
Bucket lock (opening end) Bucket tip
Boom (right)
TYPE A

1
2
4
3
1. Fit the both ends of boom linkage
into the slots in each boom.
2. Insert the Ø4x16 screw through the
hole on the boom and into the boom
linkage, tighten the screw. Repeat for
the other side.
3. Tighten a Ø10 lock nut to one end of the Ø12 rod.
4. Slide a Ø12 washer onto the Ø12 rod from other side.
Battery
Assemble the Bucket-3 │ 19
The follow steps are only for TYPE A.
to be continued...
TYPE A