HOMCOM 370-265V70 User manual

1
USER MANUAL
IN230500056V01_UK_370-265V70 EN
●For ages: 37-96 months
●Maximum weight capacity: 25 kg
●This product contains small parts. Keep children away when
assembling this product.
●Before the first use, charge the battery for at least four hours.

2
1
Julong Toys (Jiaxing) Co.,Ltd is a children's Goods Factory integrating R&D,
engineering, production, quality control and sales. The main products are
children's electric cars, children's bicycles and other products. The company has
several professional production lines, with annual production capacity reaching
hundreds of thousands of vehicles. The company has a professional R&D
engineering team, which has been working for many years, with complete testing
equipment, to ensure that the quality of products produced by the company fully
meets the requirements of national standards.
Battery Model:
Weight Limit:
Running Speed:
Charger Output:
Age Grading:
Vehicle Size:
Normal Charging Time:
Fuse:
Motor:
12V7Ah
25kg
2- 5km/h
DC 12V1000mA
37-96 months
1260x650x 520mm
8-12 hours
WHPTC
Steering motor:12V 380#6000
Drive motor :12V 390#18000
Manufactured under license from McLaren Automotive Limited. The
“McLaren” name and logo are registered trademarks of McLaren. This
product is manufactured by JULONG TOYS (JIAXING) CO.,LTD.

3
2
● After servicing the product, adults should regularly (at least once every two
weeks) check the following main items: storage battery, charging device, outer
skin, circuit change and a switching valve. Also, check the clamp devices to
see if they are loose. If there are damages to any of the items, do not use the
product until they are properly fixed by a professional.
● Clean the vehicle with a slightly damp cloth (ensure there are no water drops).
It can be polished with non-wax furniture, keeping the surface bright and clean.
Do not use chemical solvents when wiping the plastic parts - this can cause
damage. Do not use water and soap to clean the car - this will damage the
motor and battery, causing a short circuit.
● After using the product for a while, use lubricating oil on the iron part to stop it
from rusting. Keep the car away from high temperatures and moistness, so the
plastic parts do not melt. When charging, keep away from flammable materials
to prevent a fire hazard.
● When not in use, turn off the power, ensuring all switches are on 'STOP' or
'OFF'. Do not alter the structure or wire system without authorisation. Any
maintenance or replacements must be done by a professional.
● It is highly recommended to install a power supply regulator in areas with
unstable power supply - this will protect the storage battery when charging.
● Make sure to use safety wires that are compatible with this product. Do not use
wires that are not recommended.

4
3

5
4
O1
(Pre-installed)

6
5
● Ensure all parts in the list above are in the box. Keep all packaging until the
unit is fully assembled, ensuring no parts are accidentally thrown away.
● It should take approximately 30 minutes to assemble this product.
● Adult assembly is required.
● WARNING: When unassembled, there are small parts, sharp edges and sharp
points, which could harm children.
● WARNING! CHOKING HAZARD: Keep small parts away from children.
Tools required:
● Phillips screwdriver (not included)
● Socket wrench (included)
Installing the Rear Wheel
● Place the car body upside down on a flat surface.
● Slide the wheel, a 10mm shim and an M10 nut onto one side of the rear axle.
Make sure the wheel's bulge matches the gearbox.
● Repeat on the other side.
● Use the socket wrench to tighten the nuts on both ends of the shaft in the
opposite direction.
● Attach the wheel cover by aligning the buckle and pushing firmly until it clicks
into place.

7
6
Installing the front wheel
Noted: Only two-wheel drive needs to be installed dotted line shims.
● Slide a 12mm shim, the wheel a 10mm shim and an M10 nut onto one side of
the front axle. Make sure the wheel's bulge matches the gearbox.
● Use the socket wrench to tighten the nut.
● Repeat on the other side.
● Attach the wheel cover by aligning the buckle and pushing firmly until it clicks
into place.
Installing steering wheel
● Connect the steering wheel interface to the jack on the steering rod's fixed
base (Figure 1).
● Push the connected jack and interface into the base (Figure 2).
● Insert the steering wheel into the fixed base of the steering rod. Push the
steering wheel down firmly until it clicks into place.

8
7
Installing the windshield
● Insert the windshield into the slots on the car body.
● Gently push down on the windshield until it clicks into place.
Installing the rearview mirror
● Align the right rearview mirror's bayonet with the slot on the window and push it
inward until it clicks into place.
● Repeat on the other side.
● Note: The rearview mirrors are different for the left and right sides.

9
8
Connecting the power/installing the seat
● Connect the battery interface to the jack (Figure 1).
● Insert the seat back hook into the body slot, then push the bottom of the seat
into the seat slot.
● Secure the seat using two 4*12mm flat head screws (Figure 2).

10
9
WARNING
To avoid damaging the gearbox, ensure the product is at a complete stop when
switching between driving forwards and backwards.
Operation instructions
● Power: Push the power switch to turn on the car. Press again to turn off.
● Pedal: Press the foot pedal down to go. Release the foot pedal to stop.
● Forward/Backward: Push switch up to 'D' to move forward. Push switch back to
'R' to move backwards. Push switch to 'P' to park.
● Right/Left: Use the steering wheel to turn left or right.
● Light Switch: Press to turn the lights on and off.
● Hom: Push the button on the right to sound the horn.
● Music :Push the button on the left to switch between music channels.