Home Decorators Collection PARKBRIDGE 2357FMM-26-242 User manual

Item #1006295808
Model #2357FMM-26-242
ASSEMBLY INSTRUCTIONS
PARKBRIDGE 68 IN INFRARED MEDIA
FIREPLACE IN LIGHT GRAY
Questions, problems, missing parts?
Before returning to the store, call Home Decorators Collection Customer Service
8 a.m. - 7 p.m., EST, Monday - Friday, 9 a.m. - 6 p.m., EST, Saturday
1-800-986-3460
HOMEDEPOT.COM/HOMEDECORATORS
THANK YOU
We appreciate the trust and condence you have placed in Home Decorators Collection through the purchase of this replace console. We strive
to continually create quality products designed to enhance your home. Visit us online to see our full line of products available for your home
improvement needs. Thank you for choosing Home Decorators Collection!

2
Table of Contents
Table of Contents ...................................2
Safety Information ..................................2
Important Instructions ..............................2
Warranty ..........................................5
Pre-Installation.....................................6
Planning Installation ...............................6
Tools Required ....................................6
Hardware Included.................................6
Package Contents .................................7
Installation ........................................8
Maximum Recommended Weight Loads ................16
Operating Instructions ..............................17
Care and Maintenance ..............................19
Troubleshooting ...................................20
Service Parts......................................21
Safety Information
Please read and understand this entire manual before attempting to assemble, operate or install the product.
This equipment has been tested and found to comply with the limits for Class B digital devices, pursuant to Part 15 of the FCC rules. These
limits are designed to provide reasonable protection against harmful interference in a residential installation. The equipment generates,
uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful
interference to radio or television reception, which can be determined by turning the equipment off and on. The user is encouraged to try
and correct the interference by one or more of the following measures:
□Reorient or relocate the receiving antenna
□Increase the separation between the equipment and the receiver
□Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
□Consult the dealer or an experienced radio/TV technician for help.
This device complies with Part 15 of the FCC rules. Operation is subject to the following two conditions:
1. This device may not cause harmful interference, and
2. This device must accept any interference received, including interference that may cause undesired operation.
Modifications not approved by the party responsible for compliance could void user’s authority to operate the equipment.
This Class B digital apparatus complies with Canadian ICES-003.
IMPORTANT INSTRUCTIONS
When using electrical appliances, basic precautions should always be followed to reduce the risk of fire, electric shock and injury to
persons, including the following:
DANGER:
□To reduce the risk of electrical shock, ensure the product is stable, and avoid tipping.
□Read all instructions before installing or using this heater.
□If the information in this manual is not followed exactly, an electric shock or fire may result causing property damage, personal injury or loss
of life.
□ALWAYS unplug this appliance/furnishing from the electrical outlet before cleaning or servicing.
□This product is intended to fit most plasma and LCD televisions (up to 76 inches and weighing a maximum of 130 pounds). Using this item
with loads heavier than the stated maximum can result in tipping and/or instability, which can result in injury or even death.

3 HOMEDEPOT.COM/HOMEDECORATORS
Please contact 1-800-986-3460 for further assistance.
Safety Information (continued)
WARNING:
□This appliance is hot when in use. To avoid burns, DO NOT let bare skin touch hot surfaces. Keep combustible material, such as furniture,
pillows, bedding, papers, clothes and curtains at least 3 feet from this appliance and keep them away from the sides and rear.
□Extreme caution is necessary when any heater is used by or near children or individuals with disabilities and whenever the fireplace is left
operating and unattended.
□DO NOT run cord under carpeting. DO NOT cover cord with throw rugs, runners, or similar coverings.
□DO NOT route cord under furniture or appliances. Arrange cord away from traffic areas and where it will not be tripped over.
□DO NOT insert or allow foreign objects to enter any ventilation or exhaust opening as this may cause an electric shock or fire, or damage the
appliance.
□This appliance has hot and arcing or sparking parts inside. DO NOT use it in areas where gasoline, paint or flammable vapors or liquids are
used or stored. This fireplace should not be used as a drying rack for clothing. Christmas stockings or decorations should not be hung in the
area of it.
□Use this appliance only as described in the manual. Any other use is NOT recommended by the manufacturer and may cause fire, electric
shock or injury to persons.
□Reduce the risk of burns, re, electrical shock, or injury to persons:
□Unplug from outlet before putting on or taking off parts.
□Close supervision is necessary when this furnishing is used by, or near children, invalids, or disabled persons.
□Use this furnishing only for its intended use as described in these instructions. DO NOT use attachments not recommended by the
manufacturer.
□Keep the cord away from heated surfaces.
□Never operate the furnishing with the air openings blocked. Keep the air openings free of lint, hair, and other debris.
□Never drop or insert any object into any opening.
□DO NOT operate where aerosol (spray) products are being used or where oxygen is being administered.
□To disconnect, turn all controls to the off position, then remove plug from outlet.
□Each surface intended to support a load shall have a corresponding statement in the use instructions specifying the maximum intended load
for that surface in pounds (kilograms).
□Risk of electric shock-connect this furnishing to a properly grounded outlet only. See Grounding Instructions.
□To avoid electric shock, re, or injury, review the assembly instruction to conrm that the appropriate critical components and accessories
are being used with the furnishing.
□Death or serious injury may occur when children climb on audio and/or video equipment furniture. A remote control or toys placed on the
furnishing may encourage a child to climb on the furnishing and as a result the furnishing may tip over on to the child.
□Relocating audio and/or video equipment to furniture not specically designed to support audio and/or video equipment may result in death
or serious injury due to the furnishing collapsing or overturning onto a child.
CAUTION:
□DO NOT operate any heater with a damaged cord or plug or after the heater malfunctions. DO NOT operate any heater if it has been dropped
or damaged in any manner. Disconnect power at service panel and have heater inspected by a reputable electrician before reusing.
□Any repairs to this fireplace should be carried out by a qualified service person.
□Under no circumstances should this fireplace be modified. Parts having to be removed for servicing must be replaced prior to operating this
replace again.
□Household use only.
□DO NOT use outdoors.
□“WARNING – Death or serious injury may occur when children climb on audio and/or video equipment furniture. A remote control or toys
placed on the furnishing may encourage a child to climb on the furnishing and as a result the furnishing may tip over on to the child”.
□“WARNING – Relocating audio and/or video equipment to furniture not specically designed to support audio and/or video equipment may
result in death or serious injury due to the furnishing collapsing or overturning onto a child”.
□This heater is not intended for use in bathrooms, laundry areas and similar indoor locations. NEVER place heater where it may fall into a
bathtub or other water container.
□To disconnect this appliance, turn controls to the OFF position, then remove plug from outlet.

4
Safety Information (continued)
□ONLY connect to properly grounded outlets.
□This appliance, when installed, must be electrically grounded in accordance with local codes, with the current CSA C22.1 Canadian Electrical
Code or follow U.S.A. Installations, follow local codes and the National Electrical Code, ANSI/NFPA N0.70.
□To prevent a possible fire, DO NOT block air intakes or exhaust in any manner. DO NOT use on soft surfaces, like a bed, where opening may
become blocked.
□The heaters MUST NOT be located immediately below a socket-outlet.
□ALWAYS plug heaters directly into a wall outlet / receptacle. NEVER use with an extension cord or re-loadable power tap (outlet / power
strip).
□DO NOT slide insert on top of wood to avoid scratching wood surface.
□DO NOT place any object on top of the insert or block the air intakes / vents as this can cause the unit to overheat and could cause a re.
Electrical Connection
□A 15-Amp, 120-volt, 60 Hz circuit with a properly grounded outlet is required. Preferably, the fireplace will be on a dedicated circuit as
other appliances on the same circuit may cause the circuit breaker to trip or the fuse to blow when the heater is in operation. The unit
comes standard with 6-ft. three-wire cord, exiting from the rear of the fireplace. DO NOT exceed the current rating of the current tap.
Grounding Instructions
□This heater is for use on 120 volt. The cord has a plug as shown below. See illustration or grounding instruction. An adapter as shown
at C is available for connecting three-blade grounding type plugs to two-slot receptacles. The green grounding plug extending from
the adapter must be connected to a permanent ground such as a properly grounded outlet box. The adapter should not be used if a
three-slot grounded receptacle is available.
SAVE THESE INSTRUCTIONS
A B C
Grounding Pin
Grounding Means
Metal
Screw
Cover of
Grounding
Box
Adapter

5 HOMEDEPOT.COM/HOMEDECORATORS
Please contact 1-800-986-3460 for further assistance.
Warranty
The manufacturer warrants that your new electric replace is free from manufacturing and material defects for a period of one year from
date of purchase, subject to the following conditions and limitations.
Install and operate this electric replace in accordance with the installation and operating instructions furnished with the product at all
times. Any unauthorized repair, alteration, willful abuse, accident, or misuse of the product shall nullify this warranty.
This warranty is non-transferable, and is made to the original owner, provided that the purchase was made through an authorized supplier
of the product.
The warranty is limited to the repair or replacement of part(s) found to be defective in material or workmanship, provided that such part(s)
have been subjected to normal conditions of use and service, after said defect is conrmed by the manufacturer’s inspection.
The manufacturer may, at its discretion, fully discharge all obligations with respect to this warranty by refunding the wholesale price of the
defective part(s).
Any installation, labor, construction, transportation, or other related costs/expenses arising from defective part(s), repair, replacement, or
otherwise of same, will not be covered by this warranty, nor shall the manufacturer assume responsibility for same.
The owner/user assumes all other risks, if any, including the risk of any direct, indirect or consequential loss or damage arising out of the
use, or inability to use the product, except as provided by law.
All other warranties-expressed or implied-with respect to the product, its components and accessories, or any obligations/liabilities on the
part of the manufacturer are hereby expressly excluded.
The manufacturer neither assumes, nor authorizes any third party to assume on its behalf, any other liabilities with respect to the sale of
the product.
The warranties as outlined within this document do not apply to non-accessories used in conjunction with the installation of this product.
This warranty is void if:
1. The replace is subjected to prolonged periods of dampness or condensation.
2. Any unauthorized alteration, willful abuse, accident, or misuse of the product.
3. You do not have the original receipt of purchase.
Contact the Customer Service Team at 1-800-986-3460 or HOMEDEPOT.COM/HOMEDECORATORS.

6
Pre-Installation
PLANNING INSTALLATION
Before beginning assembly of product, make sure all parts are present. Compare parts with package contents list and hardware contents
list. If any part is missing or damaged, do not attempt to assemble the product.
Estimated Assembly Time: 50 minutes.
Tools Required for Assembly (not included): Phillips screwdriver.
TOOLS REQUIRED
Phillips
screwdriver
(not included)
HARDWARE INCLUDED
NOTE: Hardware not shown to actual size.
—AA —BB —CC —DD —EE
—
FF
—
GG
—
HH
—
II
Part Description Quantity
AA Long Bolt 20
BB Washer 20
CC Wooden Dowel 20
DD Back Panel Screw 22
EE Shelf Pin 8
FF L-Bracket 2
GG Glass Clips 2
HH Screw 8
II Touch-up Pen 1

7 HOMEDEPOT.COM/HOMEDECORATORS
Please contact 1-800-986-3460 for further assistance.
Pre-Installation (continued)
PACKAGE CONTENTS
O
A
I
H
L
E
B
F
M N
J
F G
K
G
B C D
Part Description Quantity
ATop 1
BOuter Wall 2
C Left Side Panel 1
D Right Side Panel 1
E Center Panel 1
F Side Back Panel 2
G Shelf 2
H Left Front Door 1
I Right Front Door 1
JFireplace Brick Wall 1
K Fireplace Glass Front 1
LBase And Heater 1
M Fire Log 1
N Fireplace Grate 1
ORemote Control (Battery
Inside) 1

8
Installation
1 Install right side panel
□Insert three wooden dowels (CC) into holes on the right of base (L). Attach right side panel (D), securing with two washers (BB)
and two long bolts (AA).
2
AA
BB
CC
D
AA
BB
L
1
2 Install left side panel
□Insert three wooden dowels (CC) into holes on the left of base (L). Attach left side panel (C).
NOTE: Do not secure left side panel (C) yet until the center panel (E) is attached at step 4.
CC
C
L

9 HOMEDEPOT.COM/HOMEDECORATORS
Please contact 1-800-986-3460 for further assistance.
Installation (continued)
3 Install center panel
□Insert one wooden dowel (CC) into each side of center panel (E).
CC
E
CC
4 Install center panel
□Carefully position the center panel (E) into place between left side panel (C) and right side panel (D). Secure each side with one
washer (BB) and one long bolt (AA), and use two washers (BB) and two long bolts (AA) to secure the left side panel assembly.
1
1
AA
BB
C
D
E
AA
BB
2

10
Installation (continued)
5 Install outer walls
□Insert four wooden dowels (CC) into holes on outer side of base (L). Attach outer walls (B), securing with four washers (BB) and
four long bolts (AA).
1
1
AA
B
B
L
BB
CC AA
BB
2
6 Install replace glass front
□From behind the assembly, attach the replace glass front (K), lowering it into the front groove on base (L).
□Secure the Glass by screw two glass clips (GG) onto the center panel (E) using two screws (HH).
K
E
L
1
GG
HH
2
GG
HH

11 HOMEDEPOT.COM/HOMEDECORATORS
Please contact 1-800-986-3460 for further assistance.
Installation (continued)
7 Install top
□Insert two wooden dowels (CC) into the top outer holes on both outer walls (B), left side panel (C) and right side panel (D). Attach
top (A), securing from underneath with ten washers (BB) and ten long bolts (AA).
2
BB
AA
A
CC
BB
AA
1
1
BD
CB
8 Install back panels
□Attach side back panel (F) to shelving areas using back panel screws (DD).
□Repeat for remaining side back panel (F).
DD
2
1
F
1
F
DD

12
Installation (continued)
9 Install replace grate
□Place the replace grate (N) by matching the bottom pins into the holes on the base (L).
□Slot the USB cable from the heater underneath through the cable hole on the base (L).
N
L
10 Install re log
□Remove the lm from the adhesive on the top of the replace grate (N) and place the re log (M) on the center of the replace
grate (N).
□Attach the USB cable from the heater into the USB port behind the replace grate (N).
1
3
2
M
N

13 HOMEDEPOT.COM/HOMEDECORATORS
Please contact 1-800-986-3460 for further assistance.
Installation (continued)
11 Install L-bracket
□Screw two L-bracket (FF) onto the replace brick wall (J) using four screws (HH).
HH
J
FF
HH
FF
12 Install replace brick wall
□Insert the replace brick wall (J) into the mantel, slotting it into the grooves on base (L).
□Secure it by using two screws (HH) into the L-bracket (FF).
2
FF
HH
HH J
FF

14
Installation (continued)
13 Install shelves
□From the front of the assembly, insert shelf pins (EE) at desired height, ensuring they are level. Place shelf (G) on top of shelf pins (EE).
Repeat for remaining the shelf (G).
1
EE
2
2
G
G
14 Install the doors
□Loosen the screws on the hinge arms and plates pre-attached on the outer walls (B).
□Pick up left front door (H) and attach it to outer wall (B) by engaging both door hinges simultaneously. Please follow the steps
below to combine the door hinges together.
i. Extend both hinge arms on the left front door (H) to open position.
ii. Insert the “J” hooks beneath the hinge arms into the lugs on mounting plates pre-attached on outer wall (B).
iii. Press lightly on the end of both hinge arms to engage the catch.
iv. To remove the hinge arms from the mounting plates, press gently in the release lever on the back of hinge arms.
□Once assembled, go back and fully tighten all screws.
□Repeat the same procedure to attach the other right front door (I) at the opposite side.
□Open and close the doors to make sure they are aligned and shut correctly. If necessary, adjust the screws for a good t.
Release lever
I/F
(i)
“J” hook
(ii) (iii)
I
II
III
B
B
I
H

15 HOMEDEPOT.COM/HOMEDECORATORS
Please contact 1-800-986-3460 for further assistance.
Installation (continued)
15 Align the doors
□If you need to adjust the doors, do so in the following manner.
To adjust door up or down, loosen screws (a) on both hinges, adjust door, and retighten screws.
To adjust door left or right, turn screws (b) on both hinges, in and out.
To adjust door in or out, loosen screws (c) on both hinges, adjust door, and retighten screws.
2
2
2
2
2
2
1
3
1
1
1
3
16 Adjust the levelers
NOTE: Use the pre-assembled levelers on the base of the replace to level the unit. Twist the levelers counterclockwise to
increase the height, or twist the levelers clockwise to decrease the height.
MM

16
Maximum Recommended Weight Loads
FITS UP TO MOST 193.04 cm / 76 in FLAT PANEL TVS
MAXIMUM LOAD 59.09 kg / 130 lb
MAXIMUM LOAD 4.5 kg / 9.9 lb
MAXIMUM LOAD 4.5 kg / 9.9 lb
MAXIMUM LOAD 4.5 kg / 9.9 lb
MAXIMUM LOAD 4.5 kg / 9.9 lb
MAXIMUM LOAD 22.7 kg / 50 lb
WARNING
For use with televisions weighing 130 lbs or less.
Use with heavier televisions may result instability causing tip over resulting in death or serious injury.
SKU#1006295808/Model#2357FMM-26-242
DISTRIBUTION: Greentouch Home Limited
ADDRESS: Room 4007, Central Plaza, 18 Harbour Road,Wanchai, Hong Kong
COUNTRY OF ORIGIN: VIETNAM
MANUFACTURE DATE: APR, 2021
(This date is accordance with the actual manufacture date.)

17 HOMEDEPOT.COM/HOMEDECORATORS
Please contact 1-800-986-3460 for further assistance.
Operating Instructions
Control Panel Remote Control
To use the remote control, rst remove the
plastic tab by gently pulling it out of remote
control.
Controls and Display
The control panel will display the heater setting when the unit power is turned ON. Whichever control icon you press will display the
current setting of the corresponding function. Press the control icon again to adjust the setting. Following adjustment of any setting(s), the
unit will resume to display the heater setting after 5 seconds.
Power Function
□When the unit is plugged-in but not in use, F or C will illuminate to indicate that it is in stand-by mode.
□Press the POWER ICON to turn the main power to the unit ON or OFF.
□When the unit is powered ON, the control panel will display the heater setting to indicate the unit has power.
□Functions stored in memory will resume at the last setting.
□When the unit is powered OFF, the fan will continue to blow for a 40 second cool-down cycle prior to shutting down (a
countdown will be displayed).
Flame Brightness Function
□Press the FLAME BRIGHTNESS ICON to display the current ame brightness setting.
□Press the FLAME BRIGHTNESS ICON again to scroll down through the ame brightness settings: 5, 4, 3, 2, 1, OF (OFF).
Flame Speed Function
□Press the FLAME SPEED ICON to display the current ame speed setting.
□Press the FLAME SPEED ICON again to scroll down through the ame speed settings: 5, 4, 3, 2, 1.
Heater Function
□Press the HEATER ICON to display the current heater setting.
□Press the HEATER ICON again to scroll down through the heater settings.
NOTE: Long-hold the icon to quickly scroll through settings.
□Set the heater to “HI” (High) to have the heater run continually.
□Set the heater to “OF” (OFF) to use the ame functions without heat.
□This heater has a thermostat sensor to control the ambient temperature in the surrounding area of the replace. The heater
will cycle ON and OFF to maintain the selected temperature. The thermostat setting range is 90ºF (43°C) to 65°F (18°C).

18
Operating Instructions (continued)
NOTE: This may not exactly match the room thermostat reading as their sensors are located in different areas.
□Hold down the FLAME SPEED ICON for 10 seconds to toggle between Fahrenheit and Celsius. “F” or “C” will be displayed
on the control panel (°F/°C can only be toggled from the control panel and will not work if using the remote control).
□See HEATER OVERRIDE section to disengage the heater.
Sleep Timer Function (Remote Control Only)
□The Sleep TIMER function will set a countdown to shut down the unit’s main power.
□Press the TIMER ICON to display the current Sleep Timer setting.
□Press the TIMER ICON again to scroll through the timer settings, which are: 30 (minutes), 1H, 2H, 3H, 4H, 5H, 6H, 7H, 8H,
9H, OF (OFF).
□When the timer reaches zero, it will turn OFF the main power and will maintain all the settings in memory.
HEATER OVERRIDE
The power to the heater can be disengaged to prevent the heater from being accidentally or unintentionally powered on. This feature is
primarily added to help prevent children from powering on the heater when it is not desired.
NOTE: The heater override can only be set from the control panel and will not work if using the remote control.
□First turn the main power OFF. Press the POWER ICON; as the heater setting display is ashing, press the POWER ICON again and
long-hold 20 seconds. The E3 symbol will display to indicate that the heater is now disengaged.
NOTE: The Flame and Timer functions will operate normally. Only the heater is disengaged.
□Repeat the same process to re-engage the heater function. The E3 symbol will change back to display the heater setting when the
heater is re-engaged.
MEMORY FUNCTION
□This unit has a memory function that allows you to turn off the MAIN POWER and retains all the other function settings (excluding the
SLEEP TIMER function).
□To reset the memory, unplug the unit from the wall.

19 HOMEDEPOT.COM/HOMEDECORATORS
Please contact 1-800-986-3460 for further assistance.
Care and Maintenance
□Make sure the unit is turned OFF, unplugged and the heating elements of heater are cool whenever you are cleaning the heater or
replace.
□Clean the metal trim using a water-dampened soft, clean cloth. DO NOT use brass polish or household cleaners as these products will
damage the metal trim.
□The motors used on the fan and the ame generator assembly are pre-lubricated for extended bearing life and require no further
lubrication. However, periodic cleaning/vacuuming of the fan/heater and air intake/output vents are recommended.
□When the heater is not in use, the power cord should be stored properly to avoid contact with hot or sharp objects.
□Any other servicing should be performed by an authorized service representative.
□Tips for using touch-up pen (II): For scratches, stroke in direction of scratch. For worn areas, stroke in the direction of wood grain. Rub
excess colorant promptly with a soft cloth.
□The furnishing has no user serviceable parts.
Replacing the Remote-Control Battery
When the remote control (O) stops operating or its range seems
reduced, it is time to replace the battery.
NOTE: The battery should be removed if the product is to be
left unused for a long time.
1. The battery compartment is located on the back end of the
remote control (O).
2. Press the small tab inward as you slide the battery door open
and remove the old battery.
3. Insert a new CR2025 lithium battery (not included), checking that
the + and - sides of the battery match the inside of the battery
compartment.
4. Re-insert the battery door.
BATTERY
O
NOTE: Harmful if swallowed.
Disposal of Used Battery
A battery may contain hazardous substances that could be endangering the environment and human health.
□This symbol marked on the battery and/or packaging indicates that
used battery shall not be treated as municipal waste. Instead it shall
be left at the appropriate collection point for recycling.
□By ensuring the used battery is disposed of correctly, you will help
prevent potential negative consequences for the environment and
human health. The recycling of materials will help to conserve
natural resources.
□Do not dispose of battery in re. Battery may explode or leak.
For more information about collection and recycling of used battery,
please contact your local municipality, your waste disposal service or the
point-of-sale where you purchased this battery.

20
Troubleshooting
Problem Possible cause Solution
Error E1 displayed on
control panel.
The overheat sensor has been
engaged.
Unplug unit, wait 15-20 minutes, then the sensor will reset itself. Plug the
unit back in and turn on the heater. If the problem persists, call customer
service.
NOTE: The other functions will work normally excluding the heater.
Error E2 displayed on
control panel.
The thermostat sensor is broken
or not working correctly.
Unplug unit, wait 15-20 minutes, then the sensor will reset itself. Plug the
unit back in and turn on the heater. If the problem persists, call customer
service.
NOTE: The other functions will work normally excluding the heater.
Error E3 displayed on
control panel.
Heater override function is
engaged.
See page 18 Heater Override Section for more details.
No power. The unit does not have power. Check that the power cord is securely plugged into a standard 120V
outlet. Then check to make sure the unit is powered on.
No ame effect but the unit
is powered on.
The ame effect is powered off. Push the ame brightness button until desired level is achieved.
USB cable. Connect the USB cable into the USB port behind the Fireplace Grate.
Heater and blower do
not power on but rest of
functions are working.
Heater setting. Set the heater to "HI" (High) to have the heater run continually.
Power cord gets warm to
the touch.
Normal operation. This is normal for a heater appliance as it requires more current to
operate. Check the connections of the appliance cord and the outlet.
Make sure the plug ts tightly into the outlet. During use, check the plug
and outlet frequently to determine if it is HOT; if so, discontinue use of the
appliance and consult with a qualied technician to check or change the
overheating outlet(s).
Remote control does not
work.
Weak or failing battery. Replace with 1 CR-2025 battery (See page 19 for more information).
Remote control signal
is weak and only work
sometimes.
Pressing the buttons too quickly. Press the buttons slowly and steadily to ensure the transmitter
recognizes the request.
Using the remote control too far
away or at an off angle.
Move closer to the insert; the remote control will only work within a
distance of 20 feet and 45 degrees to either side from the front of the
replace insert.
Fan motor continues to
blow after the unit is
powered off.
Normal operation. This is a standard feature; the blower runs for an additional time to cool
off the heater tubes.