Home Styles 20 08000 0771 User manual

Tool(s) required for assembly: Phillips screwdriver, Level, Drill (8 volts or less), 3/8” Drill Bit
Carton 20 08000 0772 is also needed for assembly.
20 08000 0771
IMPORTANT
Home Styles Customer Service: www.homestyles-furniture.com,
[email protected], 888-680-7460, 877-831-0319
Carefully remove all the parts from the carton and
place them individually on a soft cloth to prevent
scratches or other damage.
Carefully and strictly follow these assembly instructions
to ensure a completed product as designed.
Do not use power tools above 8 volts to assemble.
Closet Wall Hanging Unit
Rod Support
4 pcs.
F.
Back Panel
4 pcs.
D.
Side Panel
2 pcs.
C.
Side Panel
2 pcs.
Part List
Hardware List
Leveler
4 pcs.
Dowel (long)
6 pcs. (+1 extra)
Small Bracket
6 pcs. (+1 extra)
M3x16
Wood Screw for
Small Bracket
12 pcs. (+1 extra)
Plastic Cap
16 pcs. (+1 extra)
Cam Lock Screw
36 pcs. (+2 extra)
Cam Lock Screw
(long)
8 pcs. (+1 extra)
Dowel
28 pcs. (+1 extra)
M3 x.5 64
Wood Screw (long)
12 pcs. (+1 extra)
Bracket
2 pcs.
Cam Lock
52 pcs. (+6 extra)
M3 x.5 19
Wood Screw for
Leveler
16 pcs. (+1 extra)
Plug
4 pcs. (+1 extra)
Hex Wrench
1 pc.
M3 x1.5 5
Wood Screw for
Bracket
20 pcs. (+1 extra)

Assembly Instructions 2/9
IMPORTANT
Use a soft cloth between these parts and the floor.
Do not use power tools above 8 volts to assemble.
Do not tighten all the bolts until each part is properly assembled.
The unit must be level to work properly. Use the included adjustable levelers to level.
Keep Hex Wrench as the bolts may need to be tightened in the future.
G
D
C
Figure 2
Figure 1
STEP 1
Insert Cam Lock Screws into pre-drilled holes
in Top (A), Side Panels (C), (D), Bottom (G), and
Plinths (H), then tighten. (See Figure 2)
Attach Rod Supports to Side Panels (C)
and (D) with Wood Screws for Bracket
into pre-drilled holes. (See Figure 1)
H
A
C
D
Wood Screw for
Bracket
Rod Support
Wood Screw for
Bracket
Rod Support
Cam Lock Screw
Cam Lock Screw
Cam Lock Screw
Cam Lock Screw
H

Assembly Instructions 3/9
I
H
STEP 2
PlinthAttach s (H) to
Plinths (I) with Cam Locks.
(See Figure 3)
I
H
Cam Lock
Figure 3 Figure 4
D
C
F
F
G
Dowel
Cam Lock
Plastic Cap
STEP 3
Attach Side Panel (C) to Back Panel (F) with Dowels and Cam Locks.
Attach Side Panel (D) to Back Panel (F) with Dowels and Cam Locks.
Attach unit to unit with Dowels.
Attach Bottom (G) to unit with Dowels and Cam Locks.
Cover Cam Locks with Plastic Caps. (See Figure 4)

Assembly Instructions 4/9
Leveler
STEP 5
Attach Levelers to bottom of unit with
Wood Screws for Leveler into
pre-drilled holes (See Figure 5).
Wood Screw for Leveler
Figure 5
STEP 4
Attach unit from Step 2 to unit from Step 3
with Dowels and Wood Screws (long)
into pre-drilled holes.
Wood Screw (long)
Dowel

Assembly Instructions 5/9
STEP 6
Attach Small Brackets to unit with
Wood Screws for Small Bracket
into pre-drilled holes.
(See Figure 6)
STEP 7
Turn unit over to its’ upright position.
Attach Middle Panel (B) to unit with
Dowels (long), Cam Lock Screws (long)
and Cam Locks.
Cover Cam Locks with Plastic Caps.
B
Cam Lock
Dowel (long)
Cam Lock Screw (long)
Wood Screw for
Small Bracket
Figure 6
Plastic Cap
Small Bracket

Assembly Instructions 6/9
STEP 8
Attach Side Panel (C) to Back Panel (F) with Dowels and Cam Locks.
Attach Side Panel (D) to Back Panel (F) with Dowels and Cam Locks.
Attach unit to unit with Dowels.
Attach Top (A) to unit with Dowels and Cam Locks.
Cover Cam Locks with Plastic Caps.
STEP 9
Attach Small Brackets to unit with
Wood Screws for Small Bracket
into pre-drilled holes.
A
C
D
F
F
Dowel
Cam Lock
Plastic Cap
Wood Screw for
Small Bracket
Small Bracket

Assembly Instructions 7/9
Plug
STEP 10
Attach top unit to
base unit with
Cam Locks.
Cover Cam Locks
with Plastic Caps.
Cam Lock
Plastic Cap J
J
Figure 9
Figure 8
STEP 11
Place unit at desired location.
Note: If assembling multiple Closet Wall Units together,
place all units at desired location.
Level unit(s) by adjusting the adjustable
levelers on bottom of unit(s). (See Figure 7)
Note: Unit(s) must be level to proceed.
Cover holes with Plugs. (See Figure 8)
Place Rods (J) into position. (See Figure 9)
Figure 7

Assembly Instructions 8/9
Hardware List
STEP 12
Place unit at desired location.
Drill a 3/8” hole in wall in-line with
the pre-drilled hole at top of unit.
Move unit.
Insert Anchor into the wall hole
and attach Bracket with Wall Screw.
Attach Bracket at pre-drilled hole
at top of unit with Wood Screw.
Move unit back into place.
If assembling multiple Closet Wall Units
together, go to and complete Step 13 now,
then return to and complete Step 12.
Slide Tip-over Restraint through
Bracket on wall and Bracket on unit.
(See Figure 10)
Put tie end of Tip-over Restraint into lock
end of Tip-over Restraint and pull until tight.
Anchor
1 pc. (+1 extra)
Bracket
2 pcs. (+1 extra)
Tipover Restraint
1 pc. (+1 extra)
M3.5x38
Wall Screw
1 pc. (+1 extra)
M3x16
Wood Screw
1 pc. (+1 extra)
Figure 10
Wood Screw
Wall Screw
Bracket
on wall
Anchor in wall
3/8” wall hole
Pre-drilled hole
at top of unit
Tie end
Lock end
Bracket at
top of unit
Tip-over
Restraint
IMPORTANT
To help reduce the risk of the unit tipping over, the Tip-over Restraint must be installed following these instructions exactly.
Drill 3/8” hole in wall
Top of unit
Pre-drilled hole
at top of unit

Assembly Instructions 9/9
STEP 13
Note: If assembling multiple Closet Wall Units together, complete Step 13.
Attach tops of units together with Brackets and Wood Screws for Bracket into
pre-drilled holes. (See Figure 11)
Return to and complete Step 12.
Wood Screw for Bracket
Bracket
Figure 11

NEVER
use glass cleaners on
finished furniture. Ammonia
chemically attacks the finish.
allow liquids to remain on furniture.
Absorption causes parts to warp
and split and finishes to delaminate.
NEVER
CARE INSTRUCTIONS
Do not use rubber
based placemats.
PREVENT
DISCOLORING
Do not use commercial
waxes and polishes.
PREVENT
YELLOWING
Do not place hot
objects on surface.
PREVENT
FINISH DAMAGE
Do not write
directly on surface.
PREVENT
MARKING
Do not use power tools
above 8 volts to assemble.
PREVENT
CRACKING
Do not place
in direct sunlight.
PREVENT
FADING
with a soft cloth moistened
in lukewarm soap and water.
Buff with a dry clean cloth.
CLEAN
Home Styles will provide replacements free of charge for missing or damaged hardware or parts within 30 days of
purchase. Digital images of the defective parts may be required. If the product was not purchased from an authorized
retail affiliate, Home Styles is under no obligation to provide replacement parts. Parts are not available for fully assembled
items nor are parts available for sale. Replacements for missing or damaged hardware or parts may be requested at: