Home Styles 20 08001 0942 User manual

Part List
Home Styles Customer Service: www.homestyles-furniture.com,
[email protected], 888-680-7460, 877-831-0319
Tool(s) required for assembly: Phillips screwdriver, Level
IMPORTANT
Carefully remove all the parts from the carton and
place them individually on a soft cloth to prevent
scratches or other damage.
Carefully and strictly follow these assembly instructions
to ensure a completed product as designed.
Do not use power tools above 8 volts to assemble.
20 08001 0942
Kitchen Island
D.
Side Panel
1 pc.
E.
Middle Panel
1 pc.
C.
Side Panel
1 pc.
M.
Back Panel
3 pcs.
V.
Door
2 pcs.
P.
Arm
2 pcs.
Q.
Arm
2 pcs.
R.
Towel Bar
2 pcs.
Refer to later page(s) of these
instructions for drawer assembly.
X.
Drawer
1 pc.
W.
Drawer
4 pcs.
U.
Back Support
1 pc.
Carton 20 08001 0941 is also needed for assembly.
I.
Shelf
2 pcs.

Hardware List
Home Styles Customer Service: www.homestyles-furniture.com,
[email protected], 888-680-7460, 877-831-0319
IMPORTANT
Carefully remove all the parts from the carton and
place them individually on a soft cloth to prevent
scratches or other damage.
Carefully and strictly follow these assembly instructions
to ensure a completed product as designed.
Do not use power tools above 8 volts to assemble.
20 08001 0942
Kitchen Island
Cam Lock Screw
51 pcs. (+2 extra)
Cam Lock
33 pcs. (+6 extra)
Cam Lock Screw (long)
2 pcs. (+1 extra)
Dowel
26 pcs. (+1 extra)
Adjustable Pin
8 pcs. (+1 extra)
Hinge
4 pcs.
Cam Lock (small)
22 pcs. (+6 extra)
M3.5x64
Wood Screw for Base
12 pcs. (+1 extra)
M3.5x38
Wood Screw (long)
13 pcs. (+1 extra)
M3.5x25
Wood Screw (short)
21 pcs. (+1 extra)
M3x16
Wood Screw for Top
9 pcs. (+1 extra)
M3.5x16
Wood Screw for Hinge
34 pcs. (+1 extra)
M6x30
Head Cap Bolt
8 pcs. (+1 extra)
Hex Wrench
1 pc.
Small Hex Wrench
1 pc.

Assembly Instructions 2/10
IMPORTANT
Use a soft cloth between these parts and the floor.
Do not use power tools above 8 volts to assemble.
Do not tighten all the bolts until each part is properly assembled.
The unit must be level to work properly. Use the included adjustable levelers to level.
Keep Hex Wrench as the bolts may need to be tightened in the future.
STEP 1
Insert Cam Lock Screws into pre-drilled hole in Top (A),
Side Panels (C), (D), Middle Panel (E), Plinths (K) and
Back Upright (N), then tighten. (See Figure 1)
A
C
D
N
EK
K
Figure 1
Cam Lock Screw

Assembly Instructions 3/10
STEP 2
Attach Plinths (K) to Plinths (L)
with Cam Locks. (See Figure 2)
K
K
L
L
Figure 2
Figure 4
Figure 3
STEP 3
Place Base (J) upside down on a soft cloth.
Insert Dowels into pre-drilled holes in
Base (J). (See Figure 3)
Attach unit to Base (J) with Wood Screws
for Base, into pre-drilled holes. (See Figure 4)
J
Cam Lock
Wood Screw for Base
Dowel

Assembly Instructions 4/10
Figure 5
N
O
F
STEP 4
Insert Dowels and Can Lock Screws (long)
into pre-drilled holes in Back Rail (F). (See Figure 5)
Attach Back Uprights (N) and (O)
to Back Rail (F) with Cam Locks.
Dowel
Cam Lock Screw (long)
Cam Lock
STEP 5
Insert Dowels into pre-drilled holes
in unit and Front Rails (G) and (H).
Attach Middle Panel (E)
to unit with Cam Locks.
Attach Front Rails (G) and (H)
to unit with Cam Locks.
E
G
H
Dowel
Cam Lock

Assembly Instructions 5/10
STEP 6
Insert Dowels into
pre-drilled holes in unit.
Attach Side Panels (C) and
(D) to unit with Cam Locks.
C
D
Dowel
Cam Lock
M
M
Dowel
STEP 8
Insert Dowels into pre-drilled holes in unit.
Attach unit from Step 3 to unit with
Wood Screws (long), into pre-drilled holes.
Wood Screw (long)
STEP 7
Place unit upside down on a soft cloth.
Slide Back Panels (M) into position.
M

Assembly Instructions 6/10
P
Q
P
Q
R
R
Head Cap Bolt
STEP 10
Attach Back Supports (S) and (T) to unit with Wood Screws for Hinge.
(See Figure 6)
Insert Back Support (U) into pre-drilled hole in unit, then tighten.
S
T
U
STEP 9
Turn unit over to its upright position.
Attach Arms (P) to unit with Head Cap Bolts.
Slide Towel Bars (R) into pre-drilled holes in Arms (P).
Attach Arms (Q) to unit with Head Cap Bolts.
Figure 6
Wood Screw for Hinge

Assembly Instructions 7/10
V
Figure 7
V
V
STEP 11
Attach Hinges to Doors (V) with Wood
Screws for Hinge into pre-drilled holes,
then tighten. (See Figure 7)
Wood Screw
for Hinge
Hinge
STEP 12
Attach Doors (V) to unit with Wood
Screws for Hinge. (See Figure 8)
Insert Adjustable Pins into side panel
and middle panel at desired level.
(See Figure 9)
Place Shelves (I) into position.
Wood Screw
for Hinge
Adjustable Pin
I
I
V
V
Figure 8
Figure 9
STEP 13
Attach Leaf Top (B) to Top (A) with Wood Screws for Top.
A
B
Wood Screw for Top

Part List
W1.
Drawer Front
4 pcs.
W2.
Drawer Back
4 pcs.
W3.
Drawer Side
4 pcs.
W4.
Drawer Side
4 pcs.
W5.
Drawer Bottom
4 pcs.
Assembly Instructions 8/10
Drawer (W)
STEP 14
Attach Drawer Sides (W3) and
(W4) to Drawer Back (W2) with
Wood Screws (short).
Wood Screw (short)
W2
W3
W4
STEP 15
Slide Drawer Bottom (W5) into groove.
STEP 16
Insert Cam Lock Screws into pre-drilled
holes in Drawer Front (W1), then tighten.
Attach Drawer Front (W1) to
unit with Cam Locks (small).
W5
W1
Cam Lock (small)
Cam Lock Screw

Part List
Assembly Instructions 9/10
X1.
Drawer Front
1 pc.
X2.
Drawer Back
1 pc.
W3.
Drawer Side
1 pc.
W4.
Drawer Side
1 pc.
X5.
Drawer Bottom
1 pc.
Drawer (X)
STEP 17
Attach Drawer Sides (W3) and
(W4) to Drawer Back (X2) with
Wood Screws (short).
STEP 19
Insert Cam Lock Screws into pre-drilled
holes in Drawer Front (X1), then tighten.
Attach Drawer Front (X1) to
unit with Cam Locks (small).
X6.
Support
1 pc.
X1
X2
W3
W4
Wood Screw (short)
X6
X5
Wood Screw (short)
STEP 18
Slide Drawer Bottom (X5) into groove.
Attach Support (X6) to unit with Wood Screw (short).
Cam Lock (small)
Cam Lock Screw