Home Styles Hanover 88 5532 19 User manual

Part List
Hardware List
Tools required for assembly : Phillips screwdriver
IMPORTANT NOTE
Carefully remove all the parts from the carton and put
them individually on a soft cloth to prevent scratches
or other damages occuring to the wood parts.
We have taken great care in the design of this
product and request that you carefully and strictly
follow our assembly instructions to ensure a
completed product as it was designed.
A.
Top
1 pc.
F.
Back Panel
1 pc.
G.
Back Panel
1 pc.
B.
Side Panel
1 pc.
C.
Side Panel
1 pc.
D.
Stretcher
2 pcs.
E.
Stretcher
1 pc.
H.
Middle Panel
1 pc.
I.
Base
1 pc.
(Knock-Down Construction, please refer to
the page No. 7/8 and 8/8 of these instructions for steps to assemble drawers)
(Knock-Down
Construction, please refer
to page No. 6/8 of these
instructions for steps to
assemble keyboard tray)
R.
Drawer
1 pc.
P.
Pencil Tray
1 pc.
O.
Door
1 pc.
N.
Door
1 pc.
M.
Shelf
1 pc.
Q.
Drawer
1 pc.
Base Unit
88 5532 19
Hanover
Computer Cabinet
K.
Keyboard Tray
1 pc. L.
Printer Tray
1 pc.
Cam Lock
19 pcs.(+1 extra)
Cam Lock Screw
19 pcs.(+1 extra)
Adjustable Pin
4 pcs.(+1 extra)
Machine Screw
4 pcs.(+1 extra)
Magnet
2 pcs.
Wood Screw
for Base
2 pcs.(+1 extra)
Pull Handle
2 pcs.
Wood Screw (long)
for Drawer Side Part
24 pcs. (+1 extra)
Wood Screw
for Magnet and
Key board tray
14 pcs.(+1 extra)
Wood Screw
for Back Panel and Drawer Base Part
20 pcs.(+1 extra)
J.
Plinth
1 pc.
Flat Washer
2 pcs. (+1 extra )

IMPORTANT
Do not tighten up all the screws until each part is properly assembled.
Assembly Instructions 2/8
STEP 1
A
Attach 2X Magnets
to pre-drilled holes of Top (A) with Wood Screws.
Insert Cam Lock Screws into the pre-drilled holes
of Top (A), (D) and Plinth (J).Side Panel (B) and (C), Stretchers
Magnet
Wood Screw
B
D
D
C
Cam Lock Screw
J

DD
Cam Lock Screw
Cam Lock
Figure 1 E
STEP 2
Attach Stretchers (D)
and (E) onto Side Panel (B)
with Cam Locks (see Figure 1).
B
Assembly Instructions 3/8
STEP 3
Attach Middle Panel (H) to Base (I)
with Wood Screws and Flat Washer.
Attach Plinth (J) to Base (I) with
Cam Locks.
Wood Screw
Flat Washer
I
J
H

STEP 4
Assembly Instructions 4/8
Attach base unit in Step 3 to
side unit in Step 2 by,
using Cam Locks.
Slide Back Panel (F) and (G)
into the unit.
Attach Side Panel (C) to the unit
with Cam Locks.
C
G
F
FRONT VIEW
BACK VIEW
C
Cam Lock
FRONT VIEW

Figure 2
Figure 4
Figure 3
STEP 5
Slide Keyboard Tray (K), Printer Tray (L), Drawer (P) and (Q) into position.
Assemble Pull Handles to Doors (N) and (O) with Machine Screws. (See figure 4)
Place Top (A) onto the unit, using Cam Locks.
Insert Adjustable Pins into side panel and middle panel at the desired level (See figure 2), then
place Shelf (M) into position.
Attach Doors (N) and (O) by sliding the door lift hinges into the side panels lift hinges
(See figure 3).
STEP 6
Cam Lock
A
M
Q
P
K
L
N
O
Adjustable Pin
Insert 12X Wood Screws from the back of
the unit, tighten up all the Wood Screws.
Note: Please make sure unit is level
before tightening these screws.
Assembly Instructions 5/8
Machine Screw

Assembly Instructions 6/8
K1
K3
K4
K2
Keyboard Tray (K)
Part List
K4.
Base Part
1 pc.
K3.
Back Part
1 pc.
K1.
Side Part
1 pc.
K2.
Side Part
1 pc.
Attack K1 and K2 to the unit,
using a and
wood screws (10X).
Phillips screw driver
short
Attack K3 to K4, using a
and
wood screws .
Phillips screw driver
(4X)long
STEP 2
STEP 1

Assembly Instructions 7/8
Figure 1
Figure 2
MAKE SURE ROLLER
IS ON THE BACK
Q2
Q2
Q3
Q3
Q3
Q4
Q4
P
Q4
Q5
Q5
Q1
Q1
Drawer (Q)
Part List
Q1.
Front Part
1 pc.
Q5.
Base Part
1 pc.
Q2.
Back Part
1 pc.
Q3.
Side Part
1 pc.
Figure 3
Attach Q1 to Q3 and Q4, using
a and
wood screws ,
tighten halfway.
Attach Q2 to Q3 and Q4 using
wood screws ,
tighten halfway. (see Figure 1)
Phillips screw driver
(4X)
(4X)
long
long
Insert wood screws (2X)
into the pre-drilled holes in Q5,
tighten screws. (see Figure 3)
short
Slide Q5 into the grooves in Q3 and Q4.
Be sure to push Q5 all the way forward
so it meets Q1. (see Figure 2)
STEP 2
STEP 3 STEP 4
Tighten all screws used in drawer assembly.
Q4.
Side Part
1 pc.
Q1
Figure 4
STEP 1
Q2
Place Pencil Tray (P)
into position.
(see Figure 4)

Assembly Instructions 8/8
Figure 1
Figure 2
MAKE SURE ROLLER
IS ON THE BACK
R2
R2
R3
R3
R3
R4
R4
R6
R4
R5
R5
R1
R1
Drawer (R)
Part List
R1.
Front Part
1 pc.
R5.
Base Part
1 pc.
R2.
Back Part
1 pc.
R3.
Side Part
1 pc.
Figure 3
Attach R1 to R3 and R4, using
a and
wood screws ,
tighten halfway.
Attach R2 to R3 and R4 using
wood screws ,
tighten halfway. (see Figure 1)
Phillips screw driver
(6X)
(6X)
long
long
Insert wood screws (6X)
into the pre-drilled holes in R5,
tighten screws. (see Figure 3)
short
Slide R5 into the grooves in R3
and R4. Be sure to push R5 all
the way forward so it meets R1.
(see Figure 2)
STEP 2
STEP 3
STEP 4
Tighten all screws used in drawer assembly.
R4.
Side Part
1 pc.
R1
Figure 4
R6.
Metal Strip
2 pcs.
STEP 1
R2
Remove the tape
holding the Metal
Strips R6 in place.
You can adjust
the Metal Strip
for letter size or
legal size
file as shown.