Home Styles Storage Island 20 05520 0923 User manual

Part List
Hardware List
Tool(s) required for assembly: Phillips screwdriver, Level, Drill (8 volts or less), 3/16” Drill Bit, 3/8” Drill Bit
Cartons 20 05520 0921 and 0922 are also needed for assembly.
20 05520 0923
IMPORTANT
Storage Island
Cam Lock Screw
30 pcs. (+2 extra)
M4x16
Machine Screw
8 pcs.
M3 x.5 32
Wood Screw
4 pcs. (+1 extra)
E.
Bottom
1 pc.
B.
Rail
2 pcs.
C.
Rail
3 pcs.
F.
Plinth
2 pcs.
Small Hex Wrench
1 pc.
Cam Lock
30 pcs. (+6 extra)
Handle
4 pcs.
Adjustable Pin
12 pcs. (+1 extra)
Flat Washer
12 pcs. (+1 extra)
Spring Washer
12 pcs. (+1 extra)
M6x32
Head Cap Bolt
12 pcs. (+1 extra)
Hex Wrench
1 pc.
I.
Shelf
3 pcs.
Refer to later page(s) of these instructions for drawer assembly.
K.
Drawer
3 pcs.
J.
Drawer
1 pc.

Assembly Instructions 2/8
IMPORTANT
Use a soft cloth between these parts and the floor.
Do not use power tools above 8 volts to assemble.
Do not tighten all the bolts until each part is properly assembled.
The unit must be level to work properly. Use the included adjustable levelers to level.
Keep Hex Wrench as the bolts may need to be tightened in the future.
STEP 1
Insert Cam Lock Screws into pre-drilled holes in Top (A),
Bottom (E), Plinths (F), Side Panels (G) and (H), then tighten.
(See Figure 1)
H
Cam Lock Screw
Cam Lock Screw
A
F
G
E
F
Cam Lock Screw
Cam Lock Screw
Cam Lock Screw
Figure 1

Assembly Instructions 3/8
STEP 3
Attach unit form Step 2 to
Side Panel (H) with Flat Washers,
Spring Washers, Head Cap Bolts
and Cam Locks, tightening bolts
only halfway. (See Figure 3)
Attach Rails (B) and (C) to
unit with Cam Locks and
Wood Screws.
STEP 2
Attach Back Panel (D) to
Bottom (E) with Cam Locks.
(See Figure 2)
Attach Plinths (F) to unit with
Cam Locks.
F
D
B
F
C
B
C
C
Flat Washer
Cam Lock
Wood Screw
Head Cap Bolt
Spring Washer
Cam Lock
Figure 2
Figure 3
E
H

Assembly Instructions 4/8
G
Flat Washer
Wood Screw
Head Cap Bolt
Spring Washer
Cam Lock
Adjustable Pin
STEP 5
Insert Adjustable Pins
into side panels at
desired level.
Place Shelves (I) into
position.
I
I
I
STEP 4
Attach Side Panel (G) to unit with
Cam Locks, Flat Washers, Spring
Washers, Head Cap Bolts and
Wood Screws, tightening bolts
only halfway.
Turn unit to it’s
upright position.

Assembly Instructions 5/8
Part List
Drawer (J)
J1.
Drawer Front
1 pc.
J2.
Drawer Back
1 pc.
J3.
Drawer Side
1 pc.
J4.
Drawer Side
1 pc.
J5.
Drawer Bottom
1 pc.
Figure 5Figure 4
J4
J2 J3
Lock
J1
J5
Handle
Machine Screw
Lock
STEP 6
Attach Drawer Sides (J3) and (J4) to
Drawer Back (J2), then flip Locks.
(See Figures 4 and 5)
STEP 7
Slide Drawer Bottom (J5) into groove.
Attach Drawer Front (J1) to unit,
then flip Locks.
STEP 8
Attach Handle with Machine Screw.