Home Styles 5050-13 User manual

M6x19
Head Cap Bolt
14 pcs. (+1 extra)
Hex Wrench
1 pc.
M4x32
Wood Screw (long)
16 pcs. (+1 extra)
M6x45
Headless Bolt
2 pcs. (+1 extra)
M4x12
Wood Screw (short)
12 pcs. (+1 extra)
Flat Washer
12 pcs. (+1 extra )
Spring Washer
12 pcs. (+1 extra )
M6x45
Tapered Head Cap Bolt
4 pcs. (+1 extra)
Bracket
2 pcs.
Hardware List
Part List
Tool(s) required for assembly: Phillips screwdriver, Level, Drill (8 volts or less), 3/8” Drill Bit
5050-13
IMPORTANT
Home Styles Customer Service: www.homestyles-furniture.com,
[email protected], 888-680-7460, 877-831-0319
Carefully remove all the parts from the carton and
place them individually on a soft cloth to prevent
scratches or other damage.
Carefully and strictly follow these assembly instructions
to ensure a completed product as designed.
Do not use power tools above 8 volts to assemble.
Media Tower
C.
Side Frame
2 pcs.
B.
Rail
4 pcs.
A.
Cabinet
1 pc.
E.
Shelf
2 pcs.
D.
Shelf
2 pcs.
G.
Back Frame
1 pc.
Small Hex Wrench
1 pc.
F.
Side Frame
2 pcs.

Assembly Instructions 2/5
IMPORTANT
Use a soft cloth between these parts and the floor.
Do not use power tools above 8 volts to assemble.
Do not tighten all the bolts until each part is properly assembled.
The unit must be level to work properly. Use the included adjustable levelers to level.
Keep Hex Wrench as the bolts may need to be tightened in the future.
STEP 1
Attach Rails (B) to Side Frames (C)
with Flat Washers, Spring Washers
and Head Cap Bolts, tightening
bolts only halfway. (See Figure 1)
Tighten all bolts.
Flat Washer
Spring Washer
Head Cap Bolt
C
C
B
B
B
B
Figure 1
STEP 3
Slide lower Shelf (D) into unit.
Attach lower Shelf (D) to unit
with Wood Screws (long).
D
STEP 2
Slide upper Shelf (D) into unit.
Attach upper Shelf (D) to unit
with Wood Screws (long).
Wood Screw (long)
D
Wood Screw (long)

Assembly Instructions 3/5
STEP 6
Turn unit over to its upright position.
Remove handle on inside of drawer
and attach to outside of drawer with
machine screws.
Slide drawer into position.
A
STEP 5
Place Cabinet (A) upside down on a soft cloth.
Attach unit to Cabinet (A) with Flat Washers,
Spring Washers and Head Cap Bolts.
Attach unit to Cabinet (A)
with Wood Screws (long).
Head Cap Bolt
Spring Washer
Flat Washer
Handle
Machine Screw
STEP 4
Remove drawer from Cabinet (A).
Rotate drawer stop into position.
(See Figure 2)
Wood Screw (long)
A
Drawer Stop
Figure 2

STEP 9
Place upper unit onto base unit.
Attach Brackets to unit
with Head Cap Bolts,
Tapered Head Cap Bolts
and Wood Screws (short).
(See Figure 3)
Level unit by adjusting
the adjustable levelers on
bottom of unit. (See Figure 4)
STEP 7
Attach Side Frame (F) and Shelves (E)
to Back Frame (G) with Tapered Head Cap Bolts
and Wood Screws (short).
Bracket
Head Cap Bolt
Tapered Head Cap Bolt
Wood Screw (short)
Assembly Instructions 4/5
Figure 4
Figure 3
Wood Screw (short)
E
E
FG
STEP 8
Attach Side Frame (F) to unit
with Tapered Head Cap Bolts
and Wood Screws (short).
Insert Headless Bolts into
pre-drilled holes in unit.
Tapered Head Cap Bolt
Tapered Head Cap Bolt
Headless Bolt
Wood Screw (short)
F

Drill 3/8” hole in wall
Top of unit
Drill 3/8” hole in wall
Assembly Instructions 5/5
Hardware List
STEP 10
Place unit at desired location.
Drill a 3/8” hole in wall in-line with
pre-drilled hole at top of unit.
Move unit.
Insert Anchor into the wall hole
and attach Bracket with Wall Screw.
Attach Bracket at pre-drilled hole
at top of unit with Machine Screw.
Move unit back into place.
Slide Tipover Restraint through
Bracket on wall and Bracket on unit.
(See Figure 5)
Put tie end of Tipover Restraint into lock
end of Tipover Restraint and pull until tight.
M3.5x40
Wall Screw
1 pc. (+1 extra)
Figure 5
IMPORTANT
To help reduce the risk of the unit tipping over, the Tipover Restraint must be installed following these instructions exactly.
M4x10
Machine Screw
1 pc. (+1 extra)
Machine Screw
Wall Screw
Bracket
on wall
Anchor in wall
3/8” wall hole
Pre-drilled hole
at top of unit
Tie end
Lock end
Bracket at
top of unit
Tipover
Restraint
Anchor
1 pc. (+1 extra)
Bracket
2 pcs. (+1 extra)
Tipover Restraint
1 pc. (+1 extra)

NEVER
use glass cleaners on
finished furniture. Ammonia
chemically attacks the finish.
allow liquids to remain on furniture.
Absorption causes parts to warp
and split and finishes to delaminate.
NEVER
CARE INSTRUCTIONS
Do not use rubber
based placemats.
PREVENT
DISCOLORING
Do not use commercial
waxes and polishes.
PREVENT
YELLOWING
Do not place hot
objects on surface.
PREVENT
FINISH DAMAGE
Do not write
directly on surface.
PREVENT
MARKING
Do not use power tools
above 8 volts to assemble.
PREVENT
CRACKING
Do not place
in direct sunlight.
PREVENT
FADING
with a soft cloth moistened
in lukewarm soap and water.
Buff with a dry clean cloth.
CLEAN
Home Styles will provide replacements free of charge for missing or damaged hardware or parts within 30 days of
purchase. Digital images of the defective parts may be required. If the product was not purchased from an authorized
retail affiliate, Home Styles is under no obligation to provide replacement parts. Parts are not available for fully
assembled items nor are parts available for sale. Replacements for missing or damaged hardware or parts may be
requested at:
www.homestyles-furniture.com/customer-service/replacement-parts
Home Styles Customer Service: www.homestyles-furniture.com,
[email protected], 888-680-7460, 877-831-0319