Home Styles 20 05506 0031 User manual

20 05506 0031
Table
IMPORTANT
Carefully remove all the parts from the carton and
place them individually on a soft cloth to prevent
scratches or other damage.
Carefully and strictly follow these assembly instructions
to ensure a completed product as designed.
Do not use power tools above 8 volts to assemble.
Hardware List
Part List
Home Styles Customer Service: www.homestyles-furniture.com,
[email protected], 888-680-7460, 877-831-0319
Tool(s) required for assembly: Level
Hex Wrench
1 pc.
Small Hex Wrench
1 pc.
Flat Washer
8 pcs. (+1 extra)
Wood Screw
12 pcs. (+1 extra)
M8x50
Head Cap Bolt
8 pcs. (+1 extra)
D.
Leg
4 pcs.
B.
Top
1 pc.
F.
Table Slide
2 pcs.
A.
Top
1 pc.
C.
Leaf
1 pc.
Spring Washer
8 pcs. (+1 extra)
Flat Washer (Small)
12 pcs. (+1 extra)
Spring Washer (small)
12 pcs. (+1 extra)
M6x40
Head Cap Bolt (small)
12 pcs. (+1 extra)

Assembly Instructions 2/3
IMPORTANT
Use a soft cloth between these parts and the floor.
Do not use power tools above 8 volts to assemble.
Do not tighten all the bolts until each part is properly assembled.
The unit must be level to work properly. Use the included adjustable levelers to level.
Keep Key Wrench as the bolts may need to be tightened in the future.
STEP 1
Place Tops (A) and (B) upside down on a soft cloth.
Remove Table Slides (F) from their packing position by removing
Head Cap Bolts (small), Spring Washers (small) and Flat Washers (small).
(See Figure 1)
B
A
STEP 2
Attach Tops (A) and (B) by aligning
metal pins with holes and firmly
pushing together.
Engage locks by turning lock
handles clockwise 1/4 turn.
(See Figure 2)
Attach Table Slides (F) to unit
with Flat Washers (small),
Spring Washers (small),
Head Cap Bolts (small) and
Wood Screws.
(See Figures 3 and 4)
F
F
AB
F
F
Figure 2 Figure 4
Figure 3
Figure 1
Wood Screw
Head Cap Bolt (small)
Spring Washer (small)
Flat Washer (small)
Head Cap Bolt (small)
Spring Washer (small)
Flat Washer (small)

Assembly Instructions 3/3
STEP 3
Attach Legs (D) to unit with
Flat Washers, Spring Washers
and Head Cap Bolts, tightening
bolts only halfway.
(See Figure 5)
Tighten all bolts.
STEP 4
Turn table over to its upright position.
Disengage locks by turning lock handles
counter-clockwise 1/4 turn.
(See Figure 6)
Pull out both ends of table,
then place Leaf (C) in unit,
aligning metal pins with holes.
(See Figure 7)
Push table together firmly,
then engage locks by turning
lock handles clockwise 1/4 turn.
Level unit by adjusting the
adjustable levelers on bottom of legs.
(See Figure 8)
Figure 7 Figure 8
Figure 5
Metal Pin
C
D
D
D
D
Figure 6
Flat Washer
Spring Washer
Head Cap Bolt

NEVER
use glass cleaners on
finished furniture. Ammonia
chemically attacks the finish.
allow liquids to remain on furniture.
Absorption causes parts to warp
and split and finishes to delaminate.
NEVER
CARE INSTRUCTIONS
Do not use rubber
based placemats.
PREVENT
DISCOLORING
Do not use commercial
waxes and polishes.
PREVENT
YELLOWING
Do not place hot
objects on surface.
PREVENT
FINISH DAMAGE
Do not write
directly on surface.
PREVENT
MARKING
Do not use power tools
above 8 volts to assemble.
PREVENT
CRACKING
Do not place
in direct sunlight.
PREVENT
FADING
with a soft cloth moistened
in lukewarm soap and water.
Buff with a dry clean cloth.
CLEAN
Home Styles will provide replacements free of charge for missing or damaged hardware or parts within 30 days of
purchase. Digital images of the defective parts may be required. If the product was not purchased from an authorized
retail affiliate, Home Styles is under no obligation to provide replacement parts. Parts are not available for fully assembled
items nor are parts available for sale. Replacements for missing or damaged hardware or parts may be requested at:
www.homestyles-furniture.com/customer-service/replacement-parts
Home Styles Customer Service: www.homestyles-furniture.com,
[email protected], 888-680-7460, 877-831-0319