Home Styles Flexsteel 20 05503 0102 User manual

IMPORTANT
Carefully remove all the parts from the carton and
place them individually on a soft cloth to prevent
scratches or other damage.
Carefully and strictly follow these assembly instructions
to ensure a completed product as designed.
Do not use power tools above 8 volts to assemble.
Carton 20 05503 0101 is also needed for assembly.
N.
Foot
4 pcs.
M.
Support
1 pc.
C.
Side Panel
1 pc.
D.
Side Panel
1 pc.
G.
Back Panel
2 pcs.
H.
Back Panel
1 pc.
I.
Shelf
2 pcs.
J.
Shelf
4 pcs.
20 05503 0102
Entertainment Center
L.
Door
1 pc.
K.
Door
1 pc.
F.
Middle Panel
1 pc.
E.
Middle Panel
1 pc.
Hardware List
Part List
Home Styles Customer Service: www.homestyles-furniture.com,
[e-mail], 888-680-7460, 877-831-0319
Tool(s) required for assembly: Phillips screwdriver, Level, Drill (8 volts or less), 3/8” Drill Bit
Hex Wrench
1 pc.
Small Hex Wrench
1 pc.
Adjustable Pin
24 pcs. (+1 extra)
M4x25
Machine Screw
2 pcs.
M3x15
Wood Screw
4 pcs. (+1 extra)
Magnet
2 pcs.
M6x32
Head Cap Bolt
8 pcs. (+1 extra)
Cam Lock
8 pcs. (+2 extra)
Cam Lock Screw
8 pcs. (+1 extra)
Spring Washer
8 pcs.(+1 extra)
Flat Washer
8 pcs.(+1 extra)
Knob
2 pcs.

Assembly Instructions 2/5
IMPORTANT
Use a soft cloth between these parts and the floor.
Do not use power tools above 8 volts to assemble.
Do not tighten all the bolts until each part is properly assembled.
The unit must be level to work properly. Use the included adjustable levelers to level.
Keep Hex Wrench as the bolts may need to be tightened in the future.
A
B
Cam Lock Screw
Wood Screw
Magnet
Figure 1
Figure 2
STEP 1
Insert Cam Lock Screws into pre-drilled holes
in Top (A) and Base (B), then tighten. (See Figure 1)
Attach Magnets to Top (A) with Wood Screws into pre-drilled holes.
(See Figure 2)
STEP 2
Attach Support (M) and Feet (N) to Base (B).
M
N
N
N
N
B

Assembly Instructions 3/5
STEP 3
Turn unit to its’ upright position.
Attach Side Panels (C) and (D) to unit with Head Cap Bolts,
Spring Washers and Flat Washers, tightening bolts only halfway. (See Figure 3)
Attach Middle Panels (E) and (F) to unit with Cam Locks. (See Figure 4)
Slide Back Panels (G) and (H) into position.
C
D
EF
GG
H
Figure 4
Head Cap Bolt
Spring Washer
Flat Washer
Cam Lock
Adjustable Pin
Figure 6
Figure 5
Knob
Machine Screw
STEP 4
Attach Doors (K) and (L) to unit by sliding door hinges into side panel hinges.
(See Figure 5)
Attach Knobs to Doors (K) and (L) with Machine Screws.
Insert Adjustable Pins into side panels and middle panels at desired level.
(See Figure 6)
K
L
Figure 3

Assembly Instructions 4/5
Figure 7
I
I
J
J
J
J
A
Cam Lock
Flat Washer
Spring Washer
Head Cap Bolt
STEP 5
Attach Top (A) to unit with Head Cap Bolts, Spring Washers, Flat Washers and Cam Locks,
tightening bolts only halfway.
Tighten all bolts used in Steps 3 and 5.
Place Shelves (I) and (J) into position.
STEP 6
Level unit by adjusting the adjustable levelers on bottom of unit.
(See Figure 7)
Note: Unit must be level to work properly.

Assembly Instructions 5/5
Drill 3/8” hole in wall
Top of unit
Hardware List
Anchor
1 pc. (+1 extra)
Bracket
2 pcs. (+1 extra)
Tip-over Restraint
1 pc. (+1 extra)
M3.5x40
Wall Screw
1 pc. (+1 extra)
M3.5x16
Wood Screw
1 pc. (+1 extra)
STEP 7
Place unit at desired location.
Drill a 3/8” hole in wall in-line with
pre-drilled hole at top of unit.
Move unit.
Insert Anchor into the wall hole
and attach Bracket with Wall Screw.
Attach Bracket at pre-drilled hole
at top of unit with Wood Screw.
Move unit back into place.
Slide Tip-over Restraint through
Bracket on wall and Bracket on unit.
(See Figure 8)
Put tie end of Tip-over Restraint into lock
end of Tip-over Restraint and pull until tight.
Figure 8
Wood Screw
Wall Screw
Bracket
on wall
Anchor in wall
3/8” wall hole
Pre-drilled hole
at top of unit
Tie end
Lock end
Bracket at
top of unit
Tip-over
Restraint
IMPORTANT
To help reduce the risk of the unit tipping over, the Tip-over Restraint must be installed following these instructions exactly.

NEVER
use glass cleaners on
finished furniture. Ammonia
chemically attacks the finish.
allow liquids to remain on furniture.
Absorption causes parts to warp
and split and finishes to delaminate.
NEVER
CARE INSTRUCTIONS
Do not use rubber
based placemats.
PREVENT
DISCOLORING
Do not use commercial
waxes and polishes.
PREVENT
YELLOWING
Do not place hot
objects on surface.
PREVENT
FINISH DAMAGE
Do not write
directly on surface.
PREVENT
MARKING
Do not use power tools
above 8 volts to assemble.
PREVENT
CRACKING
Do not place
in direct sunlight.
PREVENT
FADING
with a soft cloth moistened
in lukewarm soap and water.
Buff with a dry clean cloth.
CLEAN
Home Styles will provide replacements free of charge for missing or damaged hardware or parts within 30 days of
purchase. Digital images of the defective parts may be required. If the product was not purchased from an authorized
retail affiliate, Home Styles is under no obligation to provide replacement parts. Parts are not available for fully assembled
items nor are parts available for sale. Replacements for missing or damaged hardware or parts may be requested at:
www.homestyles-furniture.com/customer-service/replacement-parts
Home Styles Customer Service: www.homestyles-furniture.com,
[e-mail], 888-680-7460, 877-831-0319