Home Styles 20 05001 0007 User manual

Part List
Hardware List
Home Styles Customer Service: www.homestyles-furniture.com,
[email protected], 888-680-7460, 877-831-0319
Tool(s) required for assembly: Phillips screwdriver, Level, Drill (8 volts or less), 3/8” Drill Bit
20 05001 0007
Buffet
IMPORTANT
Refer to later page(s) of these
instructions for drawer assembly.
Carefully remove all the parts from the carton and
place them individually on a soft cloth to prevent
scratches or other damage.
Carefully and strictly follow these assembly instructions
to ensure a completed product as designed.
Do not use power tools above 8 volts to assemble.
C.
Front Stretcher
1 pc.
D.
Front Stretcher
1 pc.
I.
Back Stretcher
1 pc.
M.
Shelf
1 pc.
J.
Back Panel
2 pcs.
E.
Front Upright
1 pc. G.
Divider
1 pc.
H.
Back Upright
1 pc.
F.
Back Stretcher
1 pc.
N.
Door
1 pc.
O.
Door
1 pc.
K.
Base
1 pc.
L.
Leg
2 pcs.
P.
Drawer
2 pcs.
Hex Wrench
1 pc.
Small Hex Wrench
1 pc.
M6x35
Head Cap Bolt
4 pcs. (+1 extra)
M6x50
Head Cap Bolt (long)
4 pcs. (+1 extra)
Cam Lock
10 pcs. (+2 extra)
Cross Dowel
4 pcs. (+1 extra)
Cam Lock Screw
10 pcs. (+1 extra)
M3.5x25
Wood Screw (long)
16 pcs. (+1 extra)
M3.5x13
Wood Screw (short)
8 pcs. (+1 extra)
Adjustable Pin
4 pcs. (+2 extra)
M3.5x16
Wood Screw
for Back Panel
8 pcs. (+1 extra)
Handle
2 pcs.
M4x25
Machine Screw
6 pcs.
Knob
2 pcs.
20 05001 Top carton is also needed for assembly.
A.
Side Panel
1 pc.
B.
Side Panel
1 pc.

Assembly Instructions 2/8
IMPORTANT
Use a soft cloth between these parts and the floor.
Do not use power tools above 8 volts to assemble.
Do not tighten all the bolts until each part is properly assembled.
The unit must be level to work properly. Use the included adjustable levelers to level.
Keep Hex Wrench as the bolts may need to be tightened in the future.
A
B
Figure 1
Cam Lock Screw
F
I
J
J
H
STEP 1
Insert Cam Lock Screws into pre-drilled holes
in Side Panels (A) and (B). (See Figure 1)
STEP 2
Attach Back Stretcher (F) to Side Panel (A) with
Cam Lock. (See Figure 2)
Attach Back Upright (H) to Back Stretcher (F).
Slide Back Panels (J) into place.
Attach Back Stretcher (I) to unit with
Cam Lock.
A
Cam Lock Screw
Cam Lock
Cam Lock
Figure 2

Assembly Instructions 3/8
B
Cam Lock
STEP 4
Attach Side Panel (B) to unit with
Cam Locks.
E
D
C
STEP 3
Attach Divider (G) to unit.
Attach Front Stretcher (C) to unit.
Attach Front Upright (E) to unit.
Attach Front Stretcher (D) to unit
with Cam Lock.
G
Cam Lock

Assembly Instructions 4/8
L
K
Figure 3
STEP 5
Attach Base (K) to unit with Cross Dowels and
Head Cap Bolts (long). (See Figure 3)
Attach Legs (L) to Base (K) with
Head Cap Bolts.
L
Cross Dowel
Head Cap Bolt (long)
Head Cap Bolt
STEP 6
Turn unit to its’ upright position.
Insert Adjustable Pins into
side panels at desired level.
Place Shelf (M) into position.
Attach Doors (N) and (O) to unit by
sliding door hinges into side panel hinges.
(See Figure 4)
Attach Knobs to Doors (N) and (O)
with Machine Screws. (See Figure 5)
M
N
O
Adjustable Pin
Figure 4 Figure 5

Assembly Instructions 5/8
STEP 8
Attach Top (Q) to unit with Cam Locks.
Note: Arrow label indicates front of Top.
Cam Lock
STEP 7
Insert Cam Lock Screws into
pre-drilled holes of Top (Q).
Arrow label
Cam Lock Screw
Q
Q

Part List
STEP 11
Attach Handle with Machine Screws.
Assembly Instructions 6/8
STEP 10
Slide Drawer Bottom (P5) into groove.
Attach Drawer Bottom (P5) to
unit with Wood Screws (short).
P5
P1.
Drawer Front
2 pcs.
P2.
Drawer Back
2 pcs.
P3.
Drawer Side
2 pcs.
P4.
Drawer Side
2 pcs.
P5.
Drawer Bottom
2 pcs.
Drawer (P)
STEP 9
Attach Drawer Front (P1) and Drawer
Back (P2) to Drawer Side (P3) with
Wood Screws (long).
Attach Drawer Side (P4) to unit with
Wood Screws (long).
Roller at back
P1
P2
P3
P4
Bottom
Handle
Wood Screw (long)
Wood Screw (short)
Machine Screw

Assembly Instructions 7/8
STEP 12
Slide Drawers (P) into position.
STEP 13
Level unit by adjusting the adjustable
levelers on bottom of unit.
(See Figure 6)
Insert Wood Screws for Back Panel
into pre-drilled holes of unit.
Note: Unit must be level before
tightening these screws.
Wood Screw for Back Panel
Figure 6
P
P

Assembly Instructions 8/8
Hardware List
STEP 14
Place unit at desired location.
Drill a 3/8” hole in wall in-line with
pre-drilled hole at top of unit.
Move unit.
Insert Anchor into the wall hole
and attach Bracket with Wall Screw.
Attach Bracket at pre-drilled hole
at top of unit with Wood Screw.
Move unit back into place.
Slide Tip-over Restraint through
Bracket on wall and Bracket on unit.
(See Figure 7)
Put tie end of Tip-over Restraint into lock
end of Tip-over Restraint and pull until tight.
Anchor
1 pc. (+1 extra)
Bracket
2 pcs. (+1 extra)
Tip-over Restraint
1 pc. (+1 extra)
M3.5x40
Wall Screw
1 pc. (+1 extra)
M3.5x16
Wood Screw
1 pc. (+1 extra)
Figure 7
Wood Screw
Wall Screw
Bracket
on wall
Anchor in wall
3/8” wall hole
Pre-drilled hole
at top of unit
Tie end
Lock end
Bracket at
top of unit
Tip-over
Restraint
IMPORTANT
To help reduce the risk of the unit tipping over, the Tip-over Restraint must be installed following these instructions exactly.
Drill 3/8” hole in wall
Top of unit

NEVER
use glass cleaners on
finished furniture. Ammonia
chemically attacks the finish.
allow liquids to remain on furniture.
Absorption causes parts to warp
and split and finishes to delaminate.
NEVER
CARE INSTRUCTIONS
Do not use rubber
based placemats.
PREVENT
DISCOLORING
Do not use commercial
waxes and polishes.
PREVENT
YELLOWING
Do not place hot
objects on surface.
PREVENT
FINISH DAMAGE
Do not write
directly on surface.
PREVENT
MARKING
Do not use power tools
above 8 volts to assemble.
PREVENT
CRACKING
Do not place
in direct sunlight.
PREVENT
FADING
with a soft cloth moistened
in lukewarm soap and water.
Buff with a dry clean cloth.
CLEAN
Home Styles will provide replacements free of charge for missing or damaged hardware or parts within 30 days of
purchase. Digital images of the defective parts may be required. If the product was not purchased from an authorized
retail affiliate, Home Styles is under no obligation to provide replacement parts. Parts are not available for fully assembled
items nor are parts available for sale. Replacements for missing or damaged hardware or parts may be requested at:
www.homestyles-furniture.com/customer-service/replacement-parts
Home Styles Customer Service: www.homestyles-furniture.com,
[email protected], 888-680-7460, 877-831-0319