Home Styles 88 5060 942 User manual

C.
Shelf
1 pc.
D.
Shelf
1 pc.
E.
Support
4 pcs. F.
Leg
4 pcs.
B.
Apron Frame
1 pc.
Hardware List
Part List
Tool(s) required for assembly: LevelPhillips screwdriver,
Home Styles Customer Service: www.homestyles-furniture.com,
[email protected], 888-680-7460, 877-831-0319
88 5060 942
Kitchen Island
IMPORTANT
Carton 88 5060 94Q1 or 88 5061 941 is also needed for assembly.
Hex Wrench
1 pc.
Small Hex Wrench
1 pc.
Carefully remove all the parts from the carton and
place them individually on a soft cloth to prevent
scratches or other damage.
Carefully and strictly follow these assembly instructions
to ensure a completed product as designed.
Do not use power tools above 8 volts to assemble.
M6x19
Head Cap Bolt (short)
28 pcs. (+1 extra)
Spring Washer
14 pcs. (+1 extra)
Flat Washer
14 pcs. (+1 extra)
M6x32
Head Cap Bolt (long)
4 pcs. (+1 extra)
M6x19
Head Cap Bolt
14 pcs. (+1 extra)

Assembly Instructions 2/3
IMPORTANT
Use a soft cloth between these parts and the floor.
Do not use power tools above 8 volts to assemble.
Do not tighten all the bolts until each part is properly assembled.
The unit must be level to work properly. Use the included adjustable levelers to level.
Keep Hex Wrench in a safe place as the bolts may need to be tightened up in the future.
STEP 2
Attach Supports (E) to Shelf (C)
with Head Cap Bolts (long),
tightening the bolts only half way.
(See Figure 2)
STEP 1
Attach Legs (F) to Shelves (C) and (D)
with Head Cap Bolts (short),
tightening the bolts only half way.
(See Figure 1)
Tighten all Head Cap Bolts.
Head Cap Bolt (short)
D
F
F
F
F
C
Figure 1
Figure 2
E
E
E
E
C
Head Cap Bolt (long)

Assembly Instructions 3/3
Head Cap Bolt (short)
Spring Washer
Flat Washer
STEP 3
Place Top (A) upside down on a soft cloth.
Attach the Apron Frame (B) to Top (A)
with Flat Washers, Spring Washers and
Head Cap Bolts, tightening the bolts
only half way. (See Figure 3)
Tighten all Head Cap Bolts used
in this step.
Head Cap Bolt
Spring Washer
Flat Washer
Head Cap Bolt
STEP 4
Attach the base unit to top unit
with Flat Washers, Spring Washers,
Head Cap Bolts (short) and
Head Cap Bolts, tightening the bolts
only half way. (See Figures 4 and 5)
Tighten all Head Cap Bolts used in
Steps 2 and 4.
Turn the unit over to its’ upright
position.
B
A
Figure 3
Figure 4 Figure 5
Figure 6
STEP 5
To level the unit, adjust the adjustable levelers on the bottom of unit.
(See Figure 6)
Note: Unit must be level to work properly.

NEVER
use glass cleaners on
finished furniture. Ammonia
chemically attacks the finish.
allow liquids to remain on furniture.
Absorption causes parts to warp
and split and finishes to delaminate.
NEVER
CARE INSTRUCTIONS
Do not use rubber
based placemats.
PREVENT
DISCOLORING
Do not use commercial
waxes and polishes.
PREVENT
YELLOWING
Do not place hot
objects on surface.
PREVENT
FINISH DAMAGE
Do not write
directly on surface.
PREVENT
MARKING
Do not use power tools
above 8 volts to assemble.
PREVENT
CRACKING
Do not place
in direct sunlight.
PREVENT
FADING
with a soft cloth moistened
in lukewarm soap and water.
Buff with a dry clean cloth.
CLEAN
Home Styles will provide replacements free of charge for missing or damaged hardware or parts within 30 days of
purchase. Digital images of the defective parts may be required. If the product was not purchased from an authorized
retail affiliate, Home Styles is under no obligation to provide replacement parts. Parts are not available for fully assembled
items nor are parts available for sale. Replacements for missing or damaged hardware or parts may be requested at:
www.homestyles-furniture.com/customer-service/replacement-parts
Home Styles Customer Service: www.homestyles-furniture.com,
[email protected], 888-680-7460, 877-831-0319