Home Styles Pantry 88 5523 691 User manual

Part List
IMPORTANT NOTE
Carefully remove all the parts from the carton and put
them individually on a soft cloth to prevent scratches
or other damages occurring to the parts.
We have taken great care in the design of this
product and request that you carefully and strictly
follow our assembly instructions to ensure
a completed product as it was designed.
Home Styles Consumer Assistance Line 888-680-7460 and 877-831-0319
[email protected]
88 5523 691
Pantry
For assembly see instructions in carton 88 5523 692
F.
Side Panel
1 pc.
B.
Door
2 pcs.
A.
Door
2 pcs.
C.
Side Panel
1 pc.
D.
Side Panel
1 pc.
E.
Side Panel
1 pc.

Part List
Home Styles Consumer Assistance Line 888-680-7460 and 877-831-0319
[email protected]
Tools required for assembly: Phillips screwdriver, Drill, 3/8” Drill Bit, Level
Hardware List
Hex Wrench
1 pc.
Small
Hex Wrench
1 pc.
M4x45
Machine Screw
4 pcs.
Cam Lock Screw
28 pcs.(+2 extra)
Cam Lock
28 pcs.(+6 extra)
Adjustable Pin
16 pcs. (+1 extra)
M3x15
Wood Screw
for Magnet
8 pcs. (+1 extra)
Knob
4 pcs.
Also need the parts from carton 88 5523 691
IMPORTANT NOTE
Carefully remove all the parts from the carton and put
them individually on a soft cloth to prevent scratches
or other damages occurring to the parts.
We have taken great care in the design of this
product and request that you carefully and strictly
follow our assembly instructions to ensure
a completed product as it was designed.
88 5523 692
Pantry
J.
Back Stretcher
4 pcs.
I.
Shelf
4 pcs.
O.
Top
1 pc.
P.
Bottom
1 pc.
M.
Back Piece
1 pc. N.
Back Panel
2 pcs.
K.
Back Piece
1 pc.
L.
Back Panel
2 pcs.
G.
Top
1 pc.
H.
Bottom
1 pc.
Magnet
2 pcs.
Steel Plate
Connector
2 pcs.
M3.5x16
Wood Screw
20 pcs. (+1 extra)

Assembly Instructions 2/6
IMPORTANT
* Do not tighten up all the screws until each part is properly assembled.
* You should keep Hex Wrench in a safe place as you may need to tighten up the Cam Locks in the future.
* Use a soft cloth between these parts and the floor.
* After assembly, item must be level to work properly. Use the included adjustable levelers to level.
Figure 2
Figure 1
STEP 2
Put Cam Lock Screws into the
pre-drilled holes of Tops (G), (O)
and tighten.
Attach Magnets to Tops (G) and
(O) with Wood Screws for Magnet.
(see Figure 2)
STEP 1
Put Cam Lock Screws into the pre-drilled holes
of Side Panels (C), (D), (E), (F) and Bottoms (H), (P) and tighten.
(see Figure 1)
CE
D
F
H
P
G
O
Cam Lock Screw
Cam Lock Screw
Wood Screw for Magnet
Magnet
Cam Lock Screw

Assembly Instructions 3/6
LKL
C
D
J
H
G
A
B
J
Figure 3
STEP 3
Attach Back Piece (K) to Back
Stretchers (J).
Slide Back Panels (L) into position.
Attach Side Panels (C) and (D) to unit
with Cam Locks. (See Figure 3)
Attach the unit to Bottom (H) with Cam
Locks.
STEP 4
Attach Doors (A) and (B) to unit by sliding
the door lift hinges into the side panel lift
hinges. (see Figure 4)
Attach Top (G) to unit with Cam Locks.
Assemble Knobs to Doors
(A) and (B) with Machine Screws.
(see Figure 5)
Cam Lock
Cam Lock
Figure 5
Figure 4

Assembly Instructions 4/6
STEP 5
Attach Back Piece (M) to Back
Stretchers (J).
Slide Back Panels (N) into position.
Attach Side Panels (E) and (F) to unit
with Cam Locks.
Attach the unit to Bottom (P) with Cam
Locks.
Cam Lock
Cam Lock
A
B
N
J
O
E
F
P
M
N
J
STEP 6
Attach Doors (A) and (B) to unit by sliding
the door lift hinges into the side panel lift
hinges.
Attach Top (O) to unit with Cam Locks.
Assemble Knobs to Doors
(A) and (B) with Machine Screws.

Assembly Instructions 5/6
STEP 7
Place the top unit onto the base unit.
Insert the Adjustable Pins into the
side panels at the desired level.
Place Shelves (I) into position.
STEP 8
To level the unit, adjust the adjustable
levelers on the bottom of unit. (see Figure 6)
Insert Wood Screws from the back
of the unit and tighten.
Note: Unit must be level before tightening these screws.
Attach Steel Plate Connectors with Wood Screws.
(see Figure 7)
Steel Plate Connector
Adjustable Pin
Figure 7
Figure 6
I
I
I
I
Wood Screw

Wood Screw
Wall Screw
M3.5x16
Wood Screw
1 pc.(+1 extra)
Anchor
1 pc.(+1 extra)
Bracket
2 pcs.(+1 extra)
Tipover Restraint
1 pc.(+1 extra)
Hardware List
Drill 3/8” hole in wall
Top of unit
Attention!
To help reduce the risk of the unit tipping over, the Tipover Restraint be installed followingmust
these instructions exactly!
M3.5x40
Wall Screw
1 pc.(+1 extra)
tie end
loop end
Place unit at desired location.
Drill a hole in wall3/8”
at the appropriate location.
Insert Anchor into the wall hole
and attach Bracket with Wall Screw.
Attach Bracket at pre-drilled hole at top
of unit with Wood Screw.
Use Tipover Restraint to secure Bracket
on unit to Bracket on wall.
(see Figure X)
Put tie end of Tipover Restraint into loop end
of Tipover Restraint and pull until tight.
Figure X
Assembly Instructions 6/6
Bracket
on wall
Anchor in wall
3/8” wall hole
Bracket at
top of unit
Tipover
Restraint