Honeywell Home PROSiXFLOOD Assembly instructions

PROSiXFLOOD
Wireless Flood Sensor
Installation and Setup Guide
The PROSiXFLOOD is a wireless flood sensor with
external probe (FP280) intended for use with Honeywell
Home controls that support PROSiX™ series devices.
When the probe contacts water, the sensor sends an
alarm or trouble signal to the controller depending on
zone type selected (ex. trouble = Monitor Zone; alarm =
24hr Aux) within 15 seconds*. The probe is supervised
for an open circuit (cut wire) and sends a trouble signal
up to 15 seconds after the condition is sensed. The
sensor also has a front cover tamper and wall tamper
switch.
* See Controller’s instructions for setting alarm delay
options, if available.
MOUNT THE PROSIXFLOOD
1. Open the case - firmly slide the front and back
housings in opposite directions and pull them apart.
2. Mount the PROSiXFLOOD to a wall as shown, using
the double sided tape and screws provided.
3. Connect the flood probe’s wires to the
PROSiXFLOOD terminals.
4. Mount the flood probe in the area where flood
notification is desired. Secure probe with #6 x ¾” pan
head screw provided.
5. Reattach front cover and secure with the #2 x 1/4”
screw provided.
After enrolling and before mounting, verify adequate
signal strength by conducting a sensor test (see
controller’s instructions) with the device in its intended
mounting location. Adjust the device location and
orientation as necessary.
A = Terminal Block for sensor
B= Tamper Switch
C= LED
Probe: FP280

2
ENROLL AND SETUP
Set the control in Programming Mode and when
prompted:
1. Pull the battery tab to activate the PROSiXFLOOD.
(Use the tamper switch if the battery tab is removed.)
2. The LED flashes (up to about 20 seconds*) during
enrollment.
•The device sends its unique MAC ID (Serial
Number); the controller registers the device and
displays the transmitter data on screen.
*NOTE: Enrollment time varies depending on the
signal strength between the device and the
controller.
3. When done, the LED is ON for 3 seconds and the
control beeps to confirm enrollment.
NOTE: If the device is not successfully enrolled
during the enrollment period, the LED turns off
and the device powers down. Activate the
tamper switch to restart the enrollment
process.
IMPORTANT: Once enrolled in a system, the
PROSiXFLOOD cannot be used with another controller
until it is removed from the current controller. See the
Controller’s instructions for details.
TESTING NOTE: After enrollment, the unit can be tested
by placing the probe in a cup of water. The control should
indicate a fault condition after 15 seconds.
24-HOUR ENROLLMENT DELETION AND
DEFAULT
If the device is enrolled in a panel different than the
intended panel, and you are unable to delete it from
the unintended panel, reset the device to factory
default setting:
1. Open the cover and remove the battery.
2. Hold down the tamper switch while reinserting the
battery. Rapid LED flashing indicates successful
deletion (LED flashes as if in enrollment mode). If
LED does not flash, delete was not successful.
3. Reattach the cover.
This procedure is available for 24 hours after
enrollment with a panel and the device remains
powered (battery installed).

3
LED INDICATIONS
LED
Status
Rapid Flashes for
about 20 seconds, then
ON for 3 seconds
Power Up – Enrollment
Slow Flashes
Power Up – Device enrolled; front Cover Tamper activated. To stop
flashes, clear the tamper condition by reattaching the cover. It also times
out after 10 minutes.
ON
(while in Programming Mode)
Sensor LED toggles on and off when the sensor is selected. See Sensor
Location Feature.
BATTERY REPLACEMENT
•Push the bottom latch of the mounting
bracket back to disengage it. Then slide
the back housing, up and out to remove
it from the mounting bracket.
•Slide the front and back housings in
opposite directions and pull the housings
apart.
•Remove the battery, wait 10 seconds,
then insert a new battery.
Recommended batteries:
Resideo 466
Duracell DL123A
Huiderui CR123A
Panasonic CR123A
•Place the front and back housings
together and slide them together as
shown.
BATTERY CAUTION: Risk of fire, explosion
and burns. Do not recharge, disassemble, heat
above 212°F (100°C) or incinerate. Dispose of
used batteries properly. Keep away from
children.
NOTE: Constant exposure to high or low
temperature or high humidity may reduce
battery life.
WARNING: Use only batteries specified in marking. Use of a different battery
may have a detrimental effect on product operation.
SPECIFICATIONS:
Battery: .................................. 1 x 3V Lithium, Resideo 466, Panasonic CR123A,
Duracell DL123A or Huiderui CR123A
Tamper: ............................................................................... Front Cover and Wall
RF Frequency:........................................................................................... 2.4GHz
Operating Temperature: ................................................32° – 122° F / 0° – 50° C
(Agency Compliance 32° – 120° F / 0° – 49° C)
Relative Humidity: ......................... 95% max. (Agency Compliance - 93% max.),
non-condensing
Dimensions: .......1” H x 3.13” L x 1.61” W / 25.5 mm H x 79.5 mm L x 41 mm W
APPROVAL LISTINGS:
FCC / IC
cETLus Listed
Conforms to ANSI/UL 2017
Certified to CAN/CSA STD C22.2
#205
Other Standards:
RoHS
Product must be tested at
least once each year

FEDERAL COMMUNICATIONS COMMISSION & ISED STATEMENTS
The user shall not make any changes or modifications to the equipment unless authorized by the Installation Instructions or User's Manual. Unauthorized changes or modifications could void the user's
authority to operate the equipment.
CLASS B DIGITAL DEVICE STATEMENT
This equipment has been tested to FCC requirements and has been found acceptable for use. The FCC requires the following statement for your information: This equipment generates and uses radio
frequency energy and if not installed and used properly, that is, in strict accordance with the manufacturer's instructions, may cause interference to radio and television reception. It has been type tested
and found to comply with the limits for a Class B computing device in accordance with the specifications in Part 15 of FCC Rules, which are designed to provide reasonable protection against such
interference in a residential installation. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause interference to radio or television reception,
which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
•If using an indoor antenna, replace it with a quality outdoor antenna.
•Reorient the receiving antenna until interference is reduced or eliminated.
•Move the radio or television receiver away from the receiver/control.
•Move the antenna leads away from any wire runs to the receiver/control.
•Plug the receiver/control into a different outlet so that it and the radio or television receiver are on different branch circuits.
•Consult the dealer or an experienced radio/TV technician for help.
ISED CLASS B STATEMENT
This Class B digital apparatus complies with Canadian ICES-003.
Cet appareil numérique de la classe B est conforme à la norme NMB-003 du Canada.
FCC / ISED STATEMENT
This device complies with Part 15 of the FCC Rules, and ISED’s license-exempt RSSs. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2)
This device must accept any interference received, including interference that may cause undesired operation.
Cet appareil est conforme à la partie 15 des règles de la FCC et exempt de licence RSS d’ISED. Son fonctionnement est soumis aux conditions suivantes: (1) Cet appareil ne doit pas causer
d’interférences nuisibles. (2) Cet appareil doit accepter toute interférence reçue y compris les interférences causant une réception indésirable.
Responsible Party / Issuer of Supplier’s Declaration of Conformity: Ademco Inc., a subsidiary of Resideo Technologies, Inc., 2 Corporate Center Drive.,
Melville, NY 11747, Ph: 516-577-2000
RF EXPOSURE
Warning – The antenna(s) used for this device must be installed to provide a separation distance of at least 7.8 inches (20 cm) from all
persons and must not be co-located or operating in conjunction with any other antenna or transmitter except in accordance with FCC
and ISED multi-transmitter product procedures.
Mise en Garde
Exposition aux Fréquences Radio : La/les antenne(s) utilisée(s) pour cet émetteur doit/doivent être installée(s) à une distance de
séparation d'au moins 20 cm (7,8 pouces) de toute personne et ne pas être située(s) ni fonctionner parallèlement à tout autre
transmetteur ou antenne, excepté en conformité avec les procédures de produit multi transmetteur FCC et ISED.
REFER TO THE INSTALLATION INSTRUCTIONS FOR THE CONTROL WITH WHICH THIS DEVICE IS USED, FOR
DETAILS REGARDING LIMITATIONS OF THE ENTIRE ALARM SYSTEM.
Responsible Party / Issuer of Supplier’s Declaration of Conformity: Ademco Inc., a subsidiary of Resideo Technologies, Inc., 2 Corporate Center Drive.,
Melville, NY 11747, Ph: 516-577-2000
The product should not be disposed of with other household waste. Check for the nearest authorized collection centers or authorized recyclers. The
correct disposal of end-of-life equipment will help prevent potential negative consequences for the environment and human health.
Any attempt to reverse-engineer this device by decoding proprietary protocols, de-compiling firmware, or any similar actions is strictly prohibited.
SUPPORT & WARRANTY INFORMATION
For the latest documentation and support, please go to:
www.resideo.com
For the latest warranty information, please go to:
www.security.honeywellhome.com/warranty
The Honeywell Home Trademark is used under license from Honeywell International Inc.
This product is manufactured by Resideo Technologies, Inc. and its affiliates.
2 Corporate Center Drive, Suite 100
P.O. Box 9040, Melville, NY 11747
©2020 Resideo Technologies, Inc.
www.resideo.com
Ê800-25245CaŠ
PROSiXFLOOD 800-25245C2/19 Rev C