Honeywell Home 5819S Assembly instructions

5819S &5819SBR
Wireless Shock Sensor and Transmitter
Installation and Setup Guide
GENERAL INFORMATION
The 5819S/5819SBR (brown) includes an omni-directional, built-in shock sensor, and is designed to protect window and door
surroundings. Use this Shock Sensor and Transmitter with alarm systems that support 5800 Series wireless devices.
Typical shock protection area: 10 - 12 feet / 5 - 6 foot radius (3.05m – 3.66m / 1.52m – 1.83m radius);
The coverage area can vary depending on the mounting surface.
The device supports three unique zones or “loops”:
Loop 1: Normally Open, built-in shock sensor*
Loop 2: Normally closed, built in reed switch, used with the included magnet
Loop 3: Externally wired, closed-circuit contact loop connected to the Terminal Block
*Note: This device features the option to enable Loop 1 to report both shock and reed switch
faults to the panel on a single zone (see Enroll and Program section for details).
Open the Sensor Install the Battery
BATTERY CAUTION: Risk of fire,
explosion, and burns. Do not recharge,
disassemble, heat above 212°F (100°C), or
incinerate. Dispose of used batteries
properly. Keep away from children.
ENROLL AND PROGRAM
1. Install the battery and ensure all the DIP Switches are
OFF (Highest Sensitivity setting).
2. Assign an individual zone number to each loop used* and
assign the zones as Input Type = 3 (Supervised RF).
*Note: To set Loop 1 to report both shock and reed switch
faults on a single zone, enroll Loop 1 (do not enroll Loop 2),
and set DIP Switch 4 ON after enrollment.
3. Activate any of the device loops (see loop descriptions
above) to transmit the device serial number to the control.
•For Loop 1, trigger the shock sensor by shaking the
device, or create a shock near the mounted device.
•For Loop 2, move the magnet close to and away from
the reed switch to trigger it.
•For Loop 3, Open and close the contact according to its
instructions.
4. Trigger again to complete enrollment.
The LED will flash rapidly to indicate the device is
transmitting to the control.
Alternatively, enter the device serial number manually
when prompted for the information.
DIP Switch Settings
After enrollment, test and adjust the device sensitivity
until the desired setting is achieved. (Refer to the
Test section.)
DIP SWITCH
SETTING
Most Sensitive (use this setting for
enrollment)
High Sensitivity
Medium Sensitivity
Low Sensitivity
*Set ON - Loop 1 reports both shock
and reed switch faults on a single
zone
Set OFF – Loop 1 reports shock
only
Do NOT Remove the PC Board from the back case
Resideo 466
Duracell DL123
Duracell DL123A
Panasonic CR123A

MOUNT THE SENSOR
After enrolling and before
permanently mounting, conduct
Go/No Go tests (see the
control's instructions) to verify
adequate signal strength.
Reorient or relocate the device if
necessary.
The device can be mounted in
any direction for shock sensing.
Do not mount on glass.
If using the magnet, install it
within 1” (25.4mm) of the device
as shown.
Test
Use a hard tool to carefully
simulate shock impacts on or
near the area where the device
is mounted. The LED lights
each time the shock vibrations
trip the device. Adjust the device
sensitivity as needed for the
application.
SPECIFICATIONS
Power: 1 x 3 V , Lithium Battery (included); Panasonic CR123A, Duracell DL123 or DL123A, Resideo 466
Operating Temperature: 14° to 131° F / -10° to 55° C (Agency Compliance 32° to 120° F / 0° to 49° C)
Relative Humidity: Up to 95% (Agency Compliance up to 93%); non-condensing
Dimensions: 3.05” H x 1.54” W x 1” D (77.47mm H x 39.12mm W x 25.4mm D)
Product must be tested at least once each year.
Approval Listings
FCC part 15, Class B verified
IC, RSS-210, Class B verified
cETLus
REFER TO THE INSTALLATION INSTRUCTIONS FOR THE CONTROL WITH WHICH THIS DEVICE IS USED, FOR DETAILS REGARDING LIMITATIONS OF
THE ENTIRE ALARM SYSTEM.
FEDERAL COMMUNICATIONS COMMISSION (FCC) & INDUSTRY CANADA (IC) STATEMENTS
The user shall not make any changes or modifications to the equipment unless authorized by the Installation Instructions or User's Manual. Unauthorized changes or
modifications could void the user's authority to operate the equipment.
CLASS B DIGITAL DEVICE STATEMENT
This equipment has been tested and found to comply with the limits for a Class B digital device, as defined by FCC Rules Part 15.105. The Class B Digital Device statement
can be viewed at:
https://customer.resideo.com/en-US/support/residential/codes-and-standards/FCC15105/Pages/default.aspx
FCC / IC STATEMENT
This device complies with Part 15 of the FCC Rules, and Industry Canada’s license-exempt RSSs. Operation is subject to the following two conditions: (1) This device may not
cause harmful interference, and (2) This device must accept any interference received, including interference that may cause undesired operation.
Cet appareil est conforme à la partie 15 des règles de la FCC et exempt de licence RSS d’Industrie Canada. Son fonctionnement est soumis aux conditions suivantes: (1) Cet
appareil ne doit pas causer d’interférences nuisibles. (2) Cet appareil doit accepter toute interférence reçue y compris les interférences causant une réception indésirable.
Responsible Party / Issuer of Supplier’s Declaration of Conformity: Ademco Inc., a subsidiary of Resideo Technologies, Inc., 2 Corporate Center Drive., Melville, NY 11747,
Ph: 516-577-2000
The product should not be disposed of with other household waste. Check for the nearest authorized collection centers or authorized recyclers. The correct
disposal of end-of-life equipment will help prevent potential negative consequences for the environment and human health.
Any attempt to reverse-engineer this device by decoding proprietary protocols, de-compiling firmware, or any similar actions is strictly prohibited.
SUPPORT & WARRANTY INFORMATION
For the latest documentation and online support information, please go to: www.resideo.com
For the latest warranty information, please go to: www.security.honeywellhome.com/warranty
The Honeywell Home Trademark is used under license from Honeywell International Inc.
This product manufactured by Resideo Technologies, Inc. and its affiliates
2 Corporate Center Drive, Suite 100
P.O. Box 9040, Melville, NY 11747
2020 Resideo Technologies, Inc.
www.resideo.com
Ê800-19771C$Š
800-19771C 01/16 Rev C