Honeywell NX series User manual

User's Manual
NX series
Constant and variable torque
Variable Speed Drives
for induction motors
Subject to changes without notice
hHoneywell

REFER TO THE START-UP QUICK GUIDE BELOWDURING INSTALLATION AND COMMISSIONING.
IF ANY PROBLEMS OCCUR, PLEASE CONTACT YOUR LOCAL DISTRIBUTOR.
Start-up Quick Guide
1. Check that the product corresponds to your order, see Chapter 3.
2. Read the safety instructions carefully in Chapter 1, before commencing
commissioning.
3. Before the mechanical installation, check the minimum clearances around the
unit and check the ambient conditions in Chapter 5.
4. Check the size of the motor cable, mains cable, mains fuses and check the
cable connections, read Chapters 6.1.1.1 – 6.1.1.4.
5. Follow the installation instructions, see Chapter 6.1.2.
6. Control cable sizes and the grounding system are explained in Chapter 6.2.1.
7. Select the most appropriate application from the Menu M6, page 6.1.
Instructions on using the keypad are given in Chapter 7.
8. Select the language of the keypad from the Menu M6, page 6.2. Instructions on
using the keypad are given in Chapter 7.
9. All parameters have factory default values. In order to ensure proper operation,
check the rating plate data for the values below and the corresponding
parameters of parameter group G2.1.
•nominal voltage of the motor
•nominal frequency of the motor
•nominal speed of the motor
•nominal current of the motor
•motor cosϕ
All parameters are explained in the Application Manual.
10. Follow the commissioning instructions, see Chapter 8.
11. The NX_ Frequency Converter is now ready for use.
The Manufacturer is not responsible for the use of the frequency converters
outside the instructions provided.

CONTENTS
NX USER’S MANUAL
INDEX
1 SAFETY
2 EU DIRECTIVE
3 RECEIPT OF DELIVERY
4 TECHNICAL DATA
5 INSTALLATION
6 CABLING AND CONNECTIONS
7 CONTROL KEYPAD
8 COMMISSIONING
9 FAULT TRACING
NX APPLICATION MANUAL
1 BASIC APPLICATION
2 STANDARD APPLICATION
3 LOCAL/REMOTE CONTROL APPLICATION
4 MULTI-STEP SPEED CONTROL APPLICATION
5 PID CONTROL APPLICATION
6 MULTI-PURPOSE CONTROL APPLICATION
7 PUMP AND FAN CONTROL APPLICATION

4(86)
THE NX FREQUENCY CONVERTER USER'S MANUAL
AND THE APPLICATION MANUAL
The User's Manual will provide the necessary information about the installation, commissioning
and operation of NX Frequency Converters. It is recommended that these instructions are studied,
before powering up the frequency converter for the first time.
The Application Manual provides information about the different applications included in the
standard frequency converter. Should these applications not meet the requirements of the
process, contact Honeywell for information on special applications.
This manual is available in both paper and electronic editions. It is recommended that the
electronic version be used where possible as it contains several links and cross-references to
other locations in the manual which makes it easier for the reader to move around in the manual,
to check and find things faster.

5(86)
NX User's Manual
Index
1. SAFETY.................................................................................................................................. 7
1.1 WARNINGS......................................................................................................................................7
1.2 SAFETY INSTRUCTIONS ....................................................................................................................7
1.3 EARTHING AND EARTH FAULT PROTECTION........................................................................................8
1.4 RUNNING THE MOTOR ......................................................................................................................8
2. EU DIRECTIVE....................................................................................................................... 9
2.1 CE MARKING...................................................................................................................................9
2.2 EMC DIRECTIVE ..............................................................................................................................9
2.2.1 General.....................................................................................................................................9
2.2.2 Technical criteria.......................................................................................................................9
2.2.3 NX frequency converter EMC classification...............................................................................9
2.2.4 Manufacturer's declaration of conformity.................................................................................10
3. RECEIPT OF SHIPMENT..................................................................................................... 12
3.1 TYPE DESIGNATION CODE...............................................................................................................12
3.2 STORAGE......................................................................................................................................12
3.3 MAINTENANCE...............................................................................................................................13
3.4 WARRANTY ...................................................................................................................................13
4. TECHNICAL DATA.............................................................................................................. 14
4.1 INTRODUCTION ..............................................................................................................................14
4.2 POWER RATINGS ...........................................................................................................................16
4.2.1 NX5 – Mains voltage 380—500 V............................................................................................16
4.3 TECHNICAL DATA ...........................................................................................................................17
5. INSTALLATION.................................................................................................................... 19
5.1 MOUNTING ....................................................................................................................................19
5.2 COOLING.......................................................................................................................................25
5.3 POWER LOSS.................................................................................................................................26
5.3.1 Power loss as function of switching frequency.........................................................................26
6. CABLING AND CONNECTIONS ......................................................................................... 28
6.1 POWER UNIT..................................................................................................................................28
6.1.1 Power connections..................................................................................................................30
6.1.1.1 Mains cable ......................................................................................................................30
6.1.1.2 Motor cable.......................................................................................................................30
6.1.1.3 Control cable ....................................................................................................................30
6.1.1.4 Cable and fuse sizes ........................................................................................................31
6.1.2 Installation instructions............................................................................................................32
6.1.2.1 Stripping lengths of motor and mains cables.....................................................................34
6.1.2.2 NX frequency converter frames and installation of cables.................................................35
6.1.3 Cable installation and the UL standards..................................................................................39
6.1.4 Cable and motor insulation checks..........................................................................................39
6.2 CONTROL UNIT ..............................................................................................................................40
6.2.1 Control connections.................................................................................................................40
6.2.1.1 Control cables...................................................................................................................42
6.2.1.2 Galvanic isolation barriers.................................................................................................42
6.2.2 Control terminal signals...........................................................................................................43
6.2.2.1 Digital input signal inversions............................................................................................44

6(86)
6.2.2.2 Jumper selections on the NXOPTA1 basic board.............................................................44
7. CONTROL KEYPAD............................................................................................................ 46
7.1 INDICATIONS ON THE KEYPAD DISPLAY............................................................................................46
7.1.1 Drive status indications............................................................................................................46
7.1.2 Control place indications .........................................................................................................47
7.1.3 Status LEDs (green – green – red)..........................................................................................47
7.1.4 Text lines.................................................................................................................................48
7.2 KEYPAD PUSH-BUTTONS ................................................................................................................49
7.2.1 Button descriptions..................................................................................................................49
7.3 NAVIGATION ON THE CONTROL KEYPAD...........................................................................................50
7.3.1 Monitoring menu (M1) .............................................................................................................52
7.3.2 Parameter menu (M2) .............................................................................................................53
7.3.3 Keypad control menu (M3) ......................................................................................................56
7.3.3.1 Selection of control place..................................................................................................56
7.3.3.2 Keypad reference.............................................................................................................57
7.3.3.3 Keypad direction...............................................................................................................57
7.3.4 Active faults menu (M4)...........................................................................................................58
7.3.4.1 Fault types........................................................................................................................58
7.3.4.2 Fault codes.......................................................................................................................60
7.3.4.3 Fault time data record.......................................................................................................62
7.3.5 Fault history menu (M5)...........................................................................................................63
7.3.6 System menu (M6)..................................................................................................................64
7.3.6.1 Application selection.........................................................................................................67
7.3.6.2 Language selection...........................................................................................................67
7.3.6.3 System settings................................................................................................................68
7.3.6.4 Keypad settings................................................................................................................71
7.3.6.5 Parameter copy................................................................................................................73
7.3.6.6 Parameter comparison .....................................................................................................75
7.3.6.7 Information submenu........................................................................................................76
7.3.6.8 Counters menu.................................................................................................................77
7.3.6.9 Trip counters submenu.....................................................................................................78
7.3.7 Expander board menu (M7).....................................................................................................79
7.4 FURTHER KEYPAD FUNCTIONS ........................................................................................................80
8. COMMISSIONING................................................................................................................ 81
8.1 SAFETY.........................................................................................................................................81
8.2 COMMISSIONING OF THE FREQUENCY CONVERTER...........................................................................81
9. FAULT TRACING.................................................................................................................84

Safety 7(86) 1
1. SAFETY
1.1 Warnings
1The components of the power unit of the frequency converter are live
when the NX is connected to mains potential. Contact with this voltage
is extremely dangerous and may cause death or severe injury. The
control unit is isolated from the potential.
2The motor terminals U, V, W and the DC-link/brake resistor terminals –/+
are live when the NX is connected to mains, even if the motor is not
running.
3The control I/O-terminals are isolated from the mains potential. However,
the relay outputs and other I/O-terminals may have a dangerous control
voltage present even when the NX is disconnected from mains.
4The frequency converter has a large capacitive leakage current.
5If the frequency converter is used as a part of a machine, the machine
manufacturer is responsible for providing the machine with a main switch
(EN 60204-1).
6Only spare parts delivered by Honeywell can be used.
1.2 Safety instructions
1The NX frequency converter is meant for fixed installations only.
2Do not perform any measurements when the frequency converter is
connected to the mains.
3After disconnecting the frequency converter from the mains, wait until the
fan stops and the indicators on the keypad extinguish. (if no keypad is
attached see the indicators on the cover). Wait 5 more minutes before
doing any work on the NX connections. Do not even open the cover
before this time has expired.
4Do not perform any voltage withstand tests on any part of the NX. There
is a defined procedure for making this test. Ignoring this procedure may
result in damage to the frequency converter.
5Prior to measurements on the motor or the motor cable, disconnect the
motor cable from the frequency converter.
6Do not touch the IC-circuits on the circuit boards. Static voltage discharge
may damage the components.
7Before connecting the frequency converter to mains, ensure that the
frequency converter front and cable covers are closed.
ONLY A COMPETENT ELECTRICIAN SHOULD CARRY OUT
THE ELECTRICAL INSTALLATION
WARNING

8(86) Safety
1
1.3 Earthing and earth fault protection
The NX frequency converter must always be earthed via a conductor connected to the earthing
terminal .
The earth fault protection inside the frequency converter protects only the converter itself against
earth faults in the motor or the motor cable.
If fault current protective switches (e.g. RCD or Earth Leakage devices) are to be used in
conjunction with the frequency converter, they must be tested with earth fault currents that are
possible to arise in fault situations.
1.4 Running the motor
Warning symbols
For your own safety please pay special attention to the instructions marked with the following
symbols:
=Dangerous voltage
WARNING =General warning
MOTOR RUN CHECK LIST
1Before starting the motor, check that the motor is mounted properly
and ensure that the machine connected to the motor allows the
motor to be started.
2Set the maximum motor speed (frequency) according to the motor
and the machine connected to it.
3Before reversing the motor shaft rotation direction make sure that
this can be done safely.
4Ensure that no power correction capacitors are connected to the
motor cable.
5Ensure that the motor terminals are not connected to mains
potential.
WARNING

Receipt of delivery 9(86)
2
2. EU DIRECTIVE
2.1 CE marking
The CE marking on the product guarantees the free movement of the product within the EEA
(European Economic Area). It also guarantees that the product meets the various requirements
defined by the directive.
The NX frequency converters carry the CE label as a proof of compliance with the Low Voltage
Directive (LVD) and the Electro Magnetic Compatibility (EMC). The company SGS FIMKO has
acted as the Competent Body.
2.2 EMC directive
2.2.1 General
The EMC Directive provides that the electrical apparatus must not excessively disturb the
environment it is used in, and also, it shall have an adequate level of immunity toward other
disturbances from the same environment.
The compliance of the NX frequency converters with the EMC directive is verified with Technical
Construction Files (TCF) checked and approved by SGS FIMKO, which is a Competent Body. The
Technical Construction Files are used to authenticate the comformity of the NX frequency
converters with the Directive due to the large product family & variety of installations possibilities.
2.2.2 Technical criteria
The NX frequency converters are marketed throughout the world, a fact which makes the EMC
requirements of customers different. As far as the immunity is concerned, all NX frequency
converters are designed to fulfil even the strictest requirements, while as regards the emission
level, the customer may want to upgrade the NX's already high ability to filter electro-magnetic
disturbances.
2.2.3 NX frequency converter EMC classification
The NX frequency converters are divided into three classes, according to the level of
electromagnetic disturbances emitted. There is no difference in the functions or the control
electronics between these classes but their EMC properties vary as follows:
Class H:
All Vacon NX frequency converters have been designed to fulfil the requirements of the
product standard EN61800-3 for the 1st environment restricted distribution and the 2nd
environment.
The emission levels correspond to the requirements of EN50081-2.
Class L:
The customer has the possibility to upgrade the EMC-disturbance filtering level of the product by
ordering the frequency converter with external EMC filters. In such case, the frequency converter
complies with the generic standards EN 50081-1, EN 50081-2 and EN 61800-3, 2nd
environment (restricted distribution).

10(86) Receipt of delivery
2
Class T:
The T-class converters have a small earth current and can be used with IT supplies only. If they
are used with other supplies no EMC requirements are complied with.
Class N:
The drives of this class do not provide EMC emission protection. This kind of drives are mounted
in enclosures.
All NX frequency converters fulfil all EMC immunity requirements (standards EN 50082-1,
50082-2 and EN 61800-3).
2.2.4 Manufacturer's declaration of conformity
The following pages present the photocopies of the Manufacturer's Declarations of Conformity
assuring the compliance of the NX frequency converters with the EMC-directives.
Warning: This is a product of the restricted sales distribution class according to IEC 61800-
3. In a domestic environment this product may cause radio interference in which case the
user may be required to take adequate measures.

Receipt of delivery 11(86)
2
EU DECLARATION OF CONFORMITY
We
Manufacturer's name: Vacon Oyj
Manufacturer's address: P.O.Box 25
Runsorintie 7
FIN-65381 Vaasa
Finland
hereby declare that the product
Product name: NXS Frequency converter
Model designation: NXS 0003…. to NXS 0205….
has been designed and manufactured in accordance with the following
standards:
Safety: EN50178 (1995), EN60204-1 (1996)
EMC: EN50082-2 (1995), EN61800-3 (1996)
and conforms to the relevant safety provisions of the Low Voltage Directive
(73/23/EEC) as amended by the Directive (93/68/EEC) and EMC
Directive 89/336/EEC.
It is ensured through internal measures and quality control that the product
conforms at all times to the requirements of the current Directive and the
relevant standards.
In Vaasa, 21st of May, 2001
Veijo Karppinen
Managing Director
The year the CE marking was affixed: 2001

12(86) Receipt of shipment
3
3. RECEIPT OF SHIPMENT
The NX frequency converters have undergone rigorous tests and quality checks at the factory
before delivery. However, after unpacking the product, check that no signs of transport damages
are to be found on the product and that the delivery is complete (compare the type designation of
the product to the code below, Figure 3-1.
Should the drive have been damaged during the shipping, contact the carrier and or distributor.
If the delivery does not correspond to your order, contact the supplier immediately.
3.1 Type designation code
Figure 3-1. NX type designation code
3.2 Storage
If the frequency converter is to be kept in store ensure that the ambient conditions are acceptable:
Storing temperature –40…+70°C
Relative humidity <95%, no condensation
NXS 0000 V 3 5
Motor current (low overload)
0007 = 7 A, 0022 = 22 A, 0205 = 205 A etc.
Voltage (3-phase):
2 = 208–240Vac, 5 = 380–500Vac, 6 = 525–690Vac (All 3-phase)
Control panel:
A = standard (alpha-numeric)
B = neutral (no local control panel)
C = special (special switches, potentiometer etc.)
D = dummy panel
EMC emission level:
H = fulfils standard IEC 61800-3 (Am 1 industrial level), 1st environment
restricted distribution, 2nd environment
T = fulfils standard IEC 61800-3 (Am 1 commercial level) for IT networks
C = fulfils standards EN50081-1, -2 and EN61800-3
Product series: NXS = standard, NXP = high-performance
Brake chopper
0 = no brake chopper
1 = internal brake chopper
2 = internal brake chopper and resistor
A 2 C 1
Enclosure class:
0 = IP00, 2 = IP21 (Nema 1), 5 = IP54 (Nema 12)
Phase:
1 = 1-phase, 3 = 3-phase
Voltage

Receipt of shipment 13(86) 3
3.3 Maintenance
In normal conditions, the NX frequency converters are maintenance-free. However, it is
recommended the heatsink be cleared periodically with compressed air.The cooling fan can easily
be changed if necessary.
3.4 Warranty
Only manufacturing defects are covered by the warranty. The manufacturer assumes no
responsibility for damages caused during or resulting from transport, receipt of the delivery,
installation, commissioning or use.
The manufacturer shall in no event and under no circumstances be held responsible for damages
and failures resulting from misuse, incorrect installation, unacceptable ambient temperature, dust,
corrosive substances or operation outside the rated specifications.
Neither can the manufacturer be held responsible for consequential damages.
The Manufacturer's period of warranty is 36 months from the delivery or 24 months from the
commissioning whichever expires first (General Conditions NL92/Orgalime S92).
The local distributor may grant a warranty time different from the above. This warranty period shall
be specified in the distributor's sales and warranty terms. The manufacturer assumes no
responsibility for warranties offered by others.With all warranty issues, please contact the
distributor first.

14(86) Technical data
4
4. TECHNICAL DATA
4.1 Introduction
Figure 4-1 presents the block diagram of the NX frequency converter. The frequency converter
consists of two units, the Power Unit and the Control Unit.
The three-phase AC-choke (1) at the mains end together with the DC-link capacitor (2) form an
LC-filter, which, again, together with the diode bridge produce the DC-voltage supply to the IGBT
Inverter Bridge (3) block. The AC-choke also functions as a filter against High Frequency
disturbances from the mains as well as against those caused by the frequency converter to the
mains. It, in addition, enhances the waveform of the input current to the frequency converter. The
entire power drawn by the frequency converter from the mains is active power.
The IGBT Inverter Bridge produces a symmetrical, 3-phase PWM-modulated AC-voltage to the
motor.
The Motor and Application Control Block is based on microprocessor software. The
microprocessor controls the motor basing on the information it receives through measurements,
parameter settings, control I/O and control keypad. The motor and application control block
controls the motor control ASIC which, in turn, calculates the IGBT positions. Gate drivers amplify
these signals for driving the IGBT inverter bridge.
Figure 4-1. NX block diagram
==
L1
L2
L3
U
V
W
3~
3~
NK4_1
Mains Motor
Brake
Chopper*
Measure-
ments
Gate
Drivers
Motor
Control
ASIC
Motor and
Application
Control
Control
Keypad
Fan
Current
Sensors
Rectifier IGBT Inverter
Brake resistor*
Output
EMC-
filter
Power
Supply
Control
I/O Control I/O Control
I/O Control I/O Control I/O
Voltage
Sensors
NXP
1)
2)
3)
Integrated input module
*Brake resistor is available as optional equipment forall classes (FR4 to FR8).
However,the brake resistor can be installed internally in classes FR4 to FR6 and is installed
externally in classes FR7 and greater.
Brake chopper belongs to the standard equipment in classes FR4 to FR6, while in greaterclasses
(FR7/FR8) itis optional.
Control
module
Power
module
Charg.res.

Technical data 15(86)
4
The control keypad provides a link between the user and the frequency converter. The control
keypad is used for parameter setting, reading status data and giving control commands. It is
detachable and can be operated externally and connected via a cable to the frequency converter.
Also a PC can be used instead of the control keypad, to control the frequency converter, if
connected through a similar cable.
Control I/O boards which are either isolated (NXOPTA8) or not isolated (NXOPTA1) from the
ground are available.
The basic control interface and the parameters (the Basic Application) are easy to use. If a more
versatile interface or parameters are required, a more suitable application can be chosen from the
Application Package. See the Application Manual for more information on the different
applications.
A brake resistor is available as external or internal option for sizes FR6 and smaller and as
external option for FR7 and bigger. Optional I/O expander boards that increase the number of
inputs and outputs to be used are also available. For details please contact your nearest
Honeywell office or your local distributor (see back cover).
The input and output EMC filters have no influence on the basic functions of the frequency
converter. They are, however, necessary for the fulfilment of the EMC directives.

16(86) Technical data
4
4.2 Power ratings
4.2.1 NX5 – Mains voltage 380—500 V
High overload = 200% starting torque, 2 sec/20 sec, 150% overloadability, 1 min/10 min
Low overload = 150% starting torque, 2 sec/20 sec, 110% overloadability, 1 min/10 min
All sizes up to and including FR8 available with IP21 enclosure and IP54 as option.
Table 4-1. Power ratings and dimensions of the NX, supply voltage 380—500V.
Mains voltage 380-500 V, 50/60 Hz, 3~
Frequency
converter
type 10%
overload 50% overload 10% overload 50% overload
40 deg C 50 deg C 40 deg C 50 deg C
P
(
kW
)
P
(
kW
)
P
(
kW
)
P
(
kW
)
NXS 0003 3,1 3,5 2,2 3,5 1,1 0,75 1,5 1,1 FR4/IP21, IP54 128x292x190 5
NXS 0004 4,0 4,4 3,1 4,4 1,5 1,1 2,2 1,5 FR4/IP21, IP54 128x292x190 5
NXS 0005 5,4 6 4 6 2,2 1,5 3 2,2 FR4/IP21, IP54 128x292x190 5
NXS 0007 7 7,7 5,4 7,7 3 2,2 4 3 FR4/IP21, IP54 128x292x190 5
NXS 0009 9 10 7 10 4 3 5,5 4 FR4/IP21, IP54 128x292x190 5
NXS 0012 12 13,2 9 13,2 5,5 4 7,5 5,5 FR4/IP21, IP54 128x292x190 5
NXS 0016 16 18 12 18 7,5 5,5 11 7,5 FR5/IP21, IP54 144x391x214 8,1
NXS 0022 22 24 16 24 11 7,5 15 11 FR5/IP21, IP54 144x391x214 8,1
NXS 0031 31 35 22 35 15 11 18,5 15 FR5/IP21, IP54 144x391x214 8,1
NXS 0038 38 47 31 47 18,5 15 22 18,5 FR6/IP21, IP54 195x519x237 18,5
NXS 0045 45 54 38 54 22 18,5 30 22 FR6/IP21, IP54 195x519x237 18,5
NXS 0061 61 68 45 68 30 22 37 30 FR6/IP21, IP54 195x519x237 18,5
NXS 0072 72 92 61 92 37 30 45 37 FR7/IP21, IP54 237x591x257 35
NXS 0087 87 108 72 108 45 37 55 45 FR7/IP21, IP54 237x591x257 35
NXS 0105 105 131 87 131 55 45 75 55 FR7/IP21, IP54 237x591x257 35
NXS 0140 140 158 105 158 75 55 90 75 FR8/IP21, IP54 285x721x288 58
NXS 0168 168 210 140 210 90 75 110 90 FR8/IP21, IP54 285x721x288 58
NXS 0205 205 252 168 252 110 90 132 110 FR8/IP21, IP54 285x721x288 58
Hi
g
hDimensions
WxHxD Weight
10%
overload
current
(A)
Rated
continuous
current IL
(A)
Motor shaft
p
ower Mechanical size
Enclosure and
protection class
Rated
Continuous
current IH
(
A
)
50%
overload
current
(A)
380V su
pp
l
y
500V su
pp
l
y
Loadabilit
y
Low

Technical data 17(86)
4
4.3 Technical data
Table 4-2. Technical data (continues on next page)
Input voltage Uin
Input frequency
Connection to mains
Output voltage
Starting torque
Output frequency
Frequency resolution
Control method
Switching frequency
(See parameter 2.6.9)
Frequency reference
Analogue input
Panel reference
Field weakening point
Acceleration time
Deceleration time
Braking torque
Ambient operating
temperature
Storage temperature
Air quality:
- chemical vapours
- mechanical particles
5...200 Hz
Displacement amplitude 3 mm at 5...10.7 Hz
Max acceleration amplitude 0.7 G at 10.7...200 Hz
Shock
EN50178, IEC 68-2-27 UPS Drop Test (for applicable UPS weights)
Storage and shipping: max 15 G, 11 ms (in package)
Ambient
conditions
IEC 721-3-3, unit in operation, class 3C2
IEC 721-3-3, unit in operation, class 3S2
Altitude 100% load capacity (no derating) up to 1000m
1-% derating for each 100m above 1000m; max. 3000m
IP21/NEMA1 standard in entire kW/HP range
IP54/NEMA12 option in entire kW/HP range
Note! Keypad installation required for IP54
Enclosure class
–40ºC...+70ºC
Relative humidity 0 to 95% RH, non-condensing, non-corrosive,
no dri
pp
in
g
water
Vibration
(IEC 721-3-3, EN50178/
EN60068-2-6, IEC68-2-6
(68-2-34, -35, -36)
208...240 V; 380...500 V; 525...690 V; -15%...+10%
45...66 Hz
Once per minute or less (normal case)
0—Uin
30...320 Hz
0...3000 sec
0...3000 sec
Motor
connection IH: Ambient temperature max. +50ºC,
overload 1.5 x IH(1min/10min)
IL: Ambient temperature max. +40ºC,
overload 1.1 x IL (1min/10min)
150% (Low overload); 200% (High overload)
0...320 Hz (NXS); 7200 Hz (Special)
0.01 Hz (NXS); Application dependent (NXP)
Starting current
Mains
connection
Continuous out
p
ut curren
t
DC-brake: 30%*TN(without brake option)
–10ºC (no frost)... +50ºC: IH
–10ºC (no frost)... +40ºC: IL
2.5 x IH2 secs every 20 secs, if output frequency <30Hz
and temperature of heatsink <+60ºC (up to 400 kW)
Frequency Control U/f
Open Loop Sensorless Vector Control
Closed Loop Frequency Control
Closed Loop Vector Control (NXP only)
Up to and including NX 0061:
1...16 kHz; Factory default 10 kHz
From NX 0072:
1...10 kHz; Factory default 3.6 kHz
Control
characteristrics
Resolution 0.1% (10bit), accuracy ±1%
Resolution 0.01 Hz

18(86) Technical data
4
Table 4-2. Technical data
Immunity
Safety
Analogue input voltage
Analogue input current
Digital inputs (6)
Auxiliary voltage
Output reference volta
ge
Analogue output
Digital outputs
Overcurrent protection
Overvoltage protection
Undervoltage protection
Mains supervision
Motor phase supervisio
n
Unit overtemperature
protection
Motor overload
protection
Motor stall protection
Motor underload
protection
Short-circuit protection
of +24V and +10V
reference voltages
NX_2: 437V; NX_5: 911V; NX_6: 1200V (all VDC)
NX_2: 183V; NX_5: 333V; NX_6: 461V (all VDC)
EMC Emissions
+24V, ±15%, max. 250mA
Relay outputs
Control
connections
Trip limit 4.0 * IH instantaneously
+10 V, +3 %, max. load 10 mA
0...+10V, Ri = 200kΩ, (–10V...+10V joystick control)
Resolution 0.1%, accuracy ±1%
EMC level H: EN50082-2, EN61800-3 (1st environment,
restricted use; 2nd environment)
Fulfil all EMC immunity requirements
EN50178, EN60204-1, CE, UL, cUL, FI,
GOST R , IEC 61800-5
(see unit nameplate for more detailed approvals)
0(4)…20mA; RLmax 500Ω, Resolution 10 bit, Accur. ±2%
Open collector output, 50mA/48V
2 programmable change over relay outputs
Max. switching voltage 125Vdc/250Vac
Max. switching current 6A/24Vdc, 0.4A/250 Vac
Max. continuous current 2 A rms
0
(
4
)
…20mA, Ri= 250Ωdifferential
Positive or negative logic; 18…24 Vdc
Yes
Yes
Protections
Trips if any of the output phases is missing
Yes
Yes
Yes
In case of earth fault in motor or motor cable, only
the frequency converter is protected
Earth-fault protection
Trips if any of the input phases is missing

Installation 19(86) 5
5. INSTALLATION
5.1 Mounting
The frequency converter can be mounted in either vertical or horizontal position on the wall or on
the back plane of a cubicle. Enough space shall be reserved around the frequency converter in
order to ensure a sufficient cooling, see Figure 5-6, Table 5-6 and Table 5-7. For safe
installation, ensure that the mounting surface is relatively even.
The frequency converter should be fixed with four screws (or bolts, depending on the unit size).
The dimensions of installation are presented in Figure 5-6 and Table 5-6.
Lift units bigger than FR7 out of the package using a jib crane. Ask the factory or your local
distributor for information on how to lift the unit safely.
Below are the dimensions of the NX frequency converters with IP21 enclosure in Figure 5-1 and
with IP21 for collar installation in Figure 5-2. The dimensions of the opening needed in collar
installation are given in Table 5-3 and Table 5-5.

20(86) Installation
5
Figure 5-1. NX dimensions, IP21
DimensionsType W1 W2 H1 H2 H3 D1 ∅E1∅E2∅*
0004—0015 NX2
0003—0012 NX5
0005—0019 NX6 128 100 327 313 292 190 7 3 x 28,3






0018—0032 NX2
0016—0031 NX5
0022—0035 NX6 144 100 419 406 391 214 7 2 x 37 1 x 28,3
0048—0092 NX2
0038—0061 NX5
0042—0085 NX6 195 148 558 541 519 237 9 3 x 37






0120—0150 NX2
0072—0105 NX5
0085—0122 NX6 237 190 630 614 591 257 9 3 x 47






0140—0205 NX5 285 255 755 732 721 288 9 3 x 59




Table 5-1. Dimensions for different frequency converter types, IP21
W1
W2
H1 H2
Ø
D1
H3
fr5ip21.fh8
Ø