Honeywell IFP-2100ECS Technical specifications

Model IFP-2100ECS
Basic Operating Instructions
These instructions must be framed and displayed next to the IFP-2100ECS panel in
accordance with NFPA 72 fire code for Local Protected Fire Alarm Systems.
FS = Fire System ECS = Emergency Communication System
Operation Task to Perform
Silence Alarms
and Troubles
Press SILENCE then enter a code if prompted. Silence LED will light.
Reset Alarms
1.
Press
RESET
.
2. Press 1 to Reset Fire System.
3. Press 2 to Reset Emergency Communication. System.
Note: To reset ECS at an LOC, the user must gain ECS Control (See Figure 1).
View all active
alarms, troubles,
and supervisory
signals
The highest priority event will display first. Press the Down arrow to view location and type of alarm or trouble.
View a Point’s
Status
1. Press ENTER to access Main Menu.
2. Press 2 to select Point Functions.
3. Then press 2 to select Point Status.
4. Select the module the device is located on by using the Up or Down button. Then pressENTER.
5. Enter the point number.
Conduct a Fire
Drill
Hold the DRILL button and then enter a code if prompted. OR
1. Enter the installer code. The panel will automatically go to the main menu.
2. Press 1 to select System Tests.
3. Enter code if prompted, then press 1 to select Fire Drill.
4. Press ENTER to start the fire drill, and Press ENTER to end the fire drill.
NOT APPROVED BY VERMONT FOR FIRE DRILLS.

Set Time and
Date
1. Enter the installer code. The panel will automatically go to the main menu.
2. Press 4 to select Set Time & Date. Enter a code if prompted.
3. Make changes to the fields on the screen as necessary.
4. Press ENTER if you wish to keep thechanges.
5. Press ENTER to set the entered time anddate.
Enable / Disable
a Point
1. Enter the installer code. The panel will automatically go to the main menu.
2. Press 2 to select Point Functions.
3. Enter code if prompted, then press 1 to select Disable / Enable Point.
4. Press 7 to select Disable/Enable Point.
5. Select the module the point is located on by using the up or down arrow. Then press ENTER.
6. Enter the point number then press ENTER.
7. Press the right arrow to Disable/Enable Point.
To Gain /Request
ECS Control
1. Press the Button and follow the on-screen Instructions.
Note: When ECS Control LED is blinking, another LOC has ECS Control. ECS Control LED is on steady when the
LOC has ECS Control.
For Service call:
[phone]

Figure 1-1: ECS Front view
Table 1-1: LED Conditions
LED Color States Meaning
Select Keys
Red
On The corresponding area is active for the currently playing ECS message.
Off The corresponding area is not active.
Green
On The corresponding area is active for the microphone.
Off The corresponding area is not active for the microphone.
Blink One or more associated network page destination panels are unable to output
the page.
ECS Control LED Green
Blink
When
this
LED
is
blinking,
someone
has
requested
control
of
the
ECS
System.
On
LOC has ECS Control and the user is able to make changes to the ECS.
Off
LOC does not have ECS Control.
Off
The corresponding ECS event was not activated from this LOC.
Green
On
The corresponding ECS event is active and was generated from the LOC (or
was activated from another LOC, but this LOC now has ECS Control).

Table 1-2: ECS Control Request
Operation Task
Gain ECS Control at an LOC
Press the ECS Control Key and enter a code if prompted. If ECS
Control is available, the ECS Control LED will illuminate. If another
LOC has ECS Control, the display will be similar to the one shown.
Press 1 to request control. The LOC with ECS Control will then be able
to allow or deny the request.
Gain ECS Control as ECS Super User at an LOC
(only one ECS Super User is allowed ECS Control
in the system at a time).
From the idle screen, enter an ECS Super User access code and then
press the ECS Control Key. If ECS Control as Super User is available,
the ECS Control LED will illuminate. If another LOC has Super User
ECS Control, a request for Super User ECS Control will automatically
be made to the LOC with control. The LOC with Super User ECS
Control will then be able to allow or deny the request. (See Figure 1-2
for screen display example).
Select all output group for microphone override
Key the microphone, wait for the Ready
-
to
-
Talk LED to light, press the
All Call Key, and then deliver your verbal message.
Select all non
-
activated output groups for
microphone override
Key the microphone, wait for the Ready
-
to
-
Talk LED to light, press the
Non-Active Call Key, and then deliver your verbal message.
Figure 1-2: Gain ECS Control as ECS Super User Screen

How to Operate the Microphone:
1. Press the ECS Control button
2. Key the Microphone
3. Press the All Call button
How to Reset the ECS System
1. Press The Reset Button
Select 2 to Reset the Emergency system
ECS-LOC2100 Operating Instruction
For Live Message
Key the Microphone.
1. Press the All Call Key or select desired output area using select keys.
2. Deliver your verbal message.
For Pre-recorded Message
1. Select desired ECS Message Key 1-8.
• If ECS Control LED is on steady, the LOC has ECS Control.
• If ECS Control LED is Blinking, another LOC has ECS Control.