Honeywell Silent Knight RA-2000 User manual

RA-2000 Remote Annunciator
Installation
The optional Model RA-2000 Remote Annunciator, shown in
Figure 1, performs the same functions as the on-board
annunciator. Operation is identical. The RA-2000 can be surface
or flush monted.
Up to 8 RA-2000s can be added to the IFP-2000 system.
Figure 1: Model RA-2000 Remote Annunciator
RA-2000 installation involves the following steps:
1. Make sure power is off at the panel.
2. Mount the RA-2000 in the desired location (see Section
“Mounting the RA-2000” ).
3. Connect the RA-2000 to the panel (see Figure 2).
4. Use the dipswitches on the back of the RA-2000 to assign
an ID# to the RA-2000 (see Section 4.10.1 of Manual P/N
151430).
5. The RA-2000 module must be added to the system through
programming. JumpStart AutoProgramming will add the
module automatically (refer to Manual P/N 151430).
Wiring Connections
Wire the RA-2000 to the FACP as Shown in Figure 2.
Figure 2: SBUS Connections
Specifications
Mounting the RA-2000
This section of the manual describes mounting the remote
annunciator. The annunciator can be flush- or surface-mounted.
Flush Mounting
This section of the manual describes flush mounting.
Follow these steps to flush mount the RA-2000
1. The back box dimensions are 9-3/8" w x 8-3/8" h. The
minimum depth 2". The back box can be mounted prior to
the complete installation of the RA-2000 using any of the
mounting holes shown in Figure 3.
Figure 3: Back Box Mounting Holes
2. Remove knockout holes as needed for wires. See Figure 4
Parameter Value
Operating Voltage: 24 VDC
Current Standby: 25 mA
Alarm: 50 mA
Operating Temperature: 0° to 49° C (32° to 120° F)
Dimensions:
Flush
Mount:
Overall: 12-1/4” W x 11.5” H x 7/8” D
31.1 cm W x 29.2 cm H x 2.2 cm D
See “Flush Mounting” for back box
dimensions.
Surface
Mount:
Including trim ring:
12-1/4” W x 11.5” H x 3” D
31.1 cm W x 29.2 cm H x 7.6 cm D
Mounting Holes
Mounting Holes

Model RA-2000 Installation Instructions
2P/N 151443 Rev A
7550 Meridian Circle, Suite 100
Maple Grove, MN 55369-4927
763-493-6455 or 800-328-0103
Fax: [phone]
www.silentknight.com
© 2008 Honeywell International Inc.
for backbox knockout locations
Figure 4: Back Box Knockout Locations
3. Wire the Annunciator board to the main control panel. See
Figure 2.
4. Attach the annunciator and door assembly to back box as
shown in Figure 5 using the supplied screws.
Figure 5: Attaching Annunciator/Door Assembly to
Backbox
Surface Mounting
The Model RA-2000TG/TR trim ring kit is available for use
when surface mounting.
1. Remove the desired knock out. See Figure 4.
2. To properly mount the back box, insert a single screw into
the key shaped mounting hole. Do not tighten all the way.
See Figure 6.
Place a level on top of the back box, with the back
box level insert the rest of the mounting screws.
Figure 6: Back Box Surface Mount Holes
3. Run wires to the control panel.
4. Place the trim ring over the back box as shown in Figure 7.
Figure 7: Installing Trim Ring
5. Attach the Door assembly to the back box using screws
provided.
6. After the annunciator wiring to the panel has been
completed, replace the electronic assembly in the back box.
Place the bezel over the back box and tighten the set screws
on the bezel.
Wire Knockouts
Wire Knockouts
Wire Knockouts
Key Shaped
Mounting Hole
Back Box
Mounting Holes