Honeywell ADEMCO 4190SN Assembly instructions

N6450-1V1 2/09 Rev. A
ADEMCO 4190SN
V-Plex®Two-Zone (SIM)
Serialized Interface Module
INSTALLATION AND SETUP GUIDE
General Information
The ADEMCO 4190SN V-Plex®is a 2-
zone expander, which allows use of the
available expansion zones provided by
controls that support V-Plex loop
devices. The 4190SN consists of two
protection loops, known as the left
(primary) and right (secondary) loops.
The left loop can be used for:
•closed-circuit devices, with or with
out EOLR supervision
•open-circuit devices with EOLR
supervision
•fast-response (10 millisecond)
devices.
Follow the chart to the right for
cutting the correct jumpers and
choosing the correct resistor when
using the left loop.
The right loop can be used for:
•closed-circuit devices only
•has no EOLR supervision
•400 millisecond response time.
The jumpers do not affect the
operation of the right loop. The right
loop cannot be used alone.
Supervision
The tamper/supervision response of
the 4190SN is determined by the zone
response type assigned to the left loop
zone. While the system is armed,
tamper/supervisory faults will report
as alarms if the left loop zone is
assigned a burglary response type and
will report as troubles if the left loop
zone is assigned a non-burglary
response type (i.e., fire, panic, aux).
While the system is disarmed, tamper/
supervisory will always report as
troubles.
Programming Notes
Program the unit like any other zone,
according to the alarm control’s
installation instructions. Enter the
following information when prompted
for in programming:
“INPUT TYPE” = “6” (SL—Serial
Number Device)
Left Zone = Loop 1
Right Zone = Loop 2
JUMPERS
USAGE (APPLIES TO
LEFT ZONE – LOOP 1
ONLY)
RED Cut for fast response
(10msec)
BLUE Cut for use with no
EOLR (closed-circuit
only). Doing this
automatically puts an
internal 10K ohm resistor
in series with the zone.
NONE CUT Use the 10K ohm
resistor provided, with
switches in either an
open-circuit or closed
circuit configuration. The
4190SN draws 2mA from
the V-Plex loop in this
mode.

4190SN
TAMPER PINS
(SHORTENED WHEN
COVER IS IN PLACE)
MOUNTING
HOLES (3)
BLUE
JUMPER
TERMINAL ASSIGNMENT
1 (+) POLLING LOOP (+)
2 (-) POLLING LOOP (-)
3 (+) LEFT LOOP 1 (+)
4 (-) COMMON (-)
5 (+) RIGHT LOOP 2 (+)
RPM
+ +
RPM
+
-
ALWAYS OBSERVE POLARITY.
ALWAYS CONNECT IN PARALLEL.
SEE TEXT FOR WIRE GUAGE AND WIRE LENGTH LIMITS.
-
-
RIGHT LOOP (LOOP 2): FOR N.C. SERIES CIRCUITS
ONLY. USE SEALED (REED) CONTACTS. SEE NOTE 1.
RIGHT LOOP NOT SUPERVISED. SEE UL NOTE 2 BELOW.
LEFT LOOP (LOOP 1): FOR N.C. CIRCUIT (INTERNAL EOLR)
OR N.C. AND/OR N.O. CIRCUIT (EXTERNAL EOLR). SEE
NOTES 2 AND 3. LEFT LOOP SUPERVISED. CLASS B, STYLE B.
SERIAL # ID
4190SN-001-V1
POLLING LOOP - SUPERVISED CLASS B, STYLE 4
CIRCUIT, 25 OHM MAX LINE IMPEDANCE
POLLING LOOP
TERMINALS ON
CONTROL
RED
JUMPER
UL Notes
1. The 4190SN is designed to meet
the following UL standards:
UL609 Commercial Burglary,
UL864 Commercial Fire, UL985
Household Fire, and UL1023
Household Burglary
2. The right loop may not be used
for Commercial Fire or UL
Commercial Burglary
installations.
3. For Commercial Fire usage: Use
N.O. contacts on the left loop.
Supervise (style B) this loop
using Model #EOL100 Fire Listed
10K ohm EOLR.
4. For UL Commercial Burglary
Usage: Use N.O. or N. C. contacts
on the left loop. Supervise using
the 10K ohm EOLR supplied.
5. All circuits are power-limited.
6. For dry indoor use only.
7. Do not install in air-handling spaces.
Note: See control panel instructions for
minimum earth ground impedance.
Specifications
Physical:
Width: 2-1/8” (53mm)
Height: 3-1/4” (81mm)
Depth: 1” (25mm)
Electrical:
Voltage Input: 8 – 12VDC
Current Drain: 2mA
Max. Loop Wire Run: 100’
Wire Gauge: 18-22 AWG
Max. Loop Line Impedance: 300 ohm
max.
REFER TO THE INSTALLATION
INSTRUCTIONS FOR THE CONTROL
PANEL WITH WHICH THE DEVICE IS
USED, FOR DETAILS ON LIMITATIONS
OF THE ENTIRE ALARM SYSTEM.
NFPA-72 Compliant
For the latest warranty information,
please go to:
http://www.security.honeywell.com/hsc/r
esources/wa/index.html
ÊN6450-1V1cŠ
N6450-1V1 2/09 Rev. A
2 Corporate Center Drive, Suite 100
P.O. Box 9040, Melville, NY 11747
Copyright2009
Honeywell International Inc.
www.honeywell.com/security