Honeywell GSMVLP5-4G Assembly instructions

800-10344 12/11 Rev. A
GSMVLP5-4G/GSMVLP5CN4G
GSM and ILP5 Ethernet
Communications Modules
Installation and Setup Guide
Installing Communication Modules
Installing the GSMVLP5-4G/GSMVLP5CN4G in the LYNX Touch Series Control
Ensure that SIM card and the connector board are securely installed in the GSMVLP5-4G/GSMVLP5CN4G
before installing the module in the LYNX Touch.
1. Install the provided FCC/IC label (P/N 800-10341) on the control’s case back (refer to Figure 1).
5000-100-186-V1
800-10341 Label
800-10259 11/11 Rev A
FCC / IC STATEMENT
IC: 573F-LYNXTOUCH2
This device complies with Part 15 of the FCC Rules, and RSS 210 of IC. Operation is subject to the
following two conditions: (1) This Device may not cause harmful interference. (2) This device must
accept any interference received, including interference that may cause undesired operation.
IC MODEL: LYNXTOUCH2
FCC ID: CFS8DLLYNXTOUCH2
CONTAINS MODULE: FCC ID: QIPPH8 IC: 7830A-PH8 IC MODEL: PH8
Figure 1. FCC/IC Label Location
2. Release the LYNX Touch front case from the back case by depressing the two locking tabs at the top of the
unit with the blade of a medium size screwdriver (Refer to Figure 2).
3. Install the GSMVLP5-4G/GSMVLP5CN-4G into the LYNX Touch control front case. Ensure that the
connector board is properly seated into the receptacle on the control (Refer to Figure 2).
4. Secure the GSMVLP5-4G/GSMVLP5CN-4G with the three provided screws (Refer to Figure 2).
5. Enable the GSMVLP5-4G/GSMVLP5CN-4G device, configure alarm reporting and module supervision and
register the device. Refer to the “Program the Radio” and “Diagnostics” sections in the LYNX Touch Series
Installation and Setup Guide (P/N 800-10614 or higher).
For Documentation and Online Support: http://www.security.honeywell.com/hsc/resources/MyWebTech

SCREW
(3)
SIM
CARD
5000-100-151-V2
ROTATED
180
CONNECTOR
BOARD
CONNECTOR
BOARD
RECEPTACLE
GSMVLP5-4G/
GSMVLP5CN4G
LYNX TOUCH
LOCKING TABS
Figure 2. Installing the GSMVLP5-4G/GSMVLP5CN4G in the LYNX Touch
Installing the ILP5 in the LYNX Touch Series Control
Ensure that the connector board and cable are securely installed in the ILP5 before installing the module in
the LYNX Touch.
1. Release the LYNX Touch front case from the back case by depressing the two locking tabs at the top of the
unit with the blade of a medium size screwdriver (Refer to Figure 3).
2. Using a wire cutter or knife cut the plastic tabs that secure the ILP5 spacer to the back case of the LYNX
Touch (Refer to Figure 3).
3. Remove the ILP5 receptacle knockout from the left side of the LYNX Touch back case (Refer to Figure 3).
4. Install the ILP5 into the LYNX Touch control front case. Ensure that the connector board is properly seated
into the receptacle on the control (Refer to Figure 3).
5. Secure the ILP5 with the three provided screws (Refer to Figure 3).
6. Insert the ILP5 receptacle and spacer into the slot on the back case (Refer to Figure 3).
7. Secure the communications cable to the tie wrap point on the ILP5 with the provided tie wrap (Refer to
Figure 3).
8. Enable the ILP5 and configure alarm reporting and module supervision and register the device. Refer to the
“Program the Radio” and “Diagnostics” sections in the LYNX Touch Series Installation and Setup Guide
(P/N 800-10614 or higher).
For Documentation and Online Support: http://www.security.honeywell.com/hsc/resources/MyWebTech

5000-100-154-V2
SCREW
(3)
ROTATED
180
CONNECTOR
BOARD
RJ45
RECEPTACLE
CONNECTOR BOARD
RECEPTACLE
ILP5
LYNX TOUCH
TIE
WRAP
POINT
REMOVE ILP5
SPACER
ILP5 SPACER
REMOVE ILP5
KNOCKOUT
TIE
WRAP
(1)
RJ45 RECEPTACLE
LYNX TOUCH
ALTERNATE INSTALLATION
LOCKING TABS
ETHERNET CABLE
TO ILP5
Figure 3. Installing the ILP5 in the LYNX Touch
Electrical Specifications
GSMVLP5-4G/GSMVLP5CN-4G
Voltage Input 5V (provided by the control panel)
Current
Idle 15 mA, standby
Average 300mA, average transmit
Peak 1.6A peak transmit, 25% duty cycle
ILP5
Voltage Input 5V (provided by the control panel)
Current: 83 mA, 100 Base T with traffic
41 mA , 10 Base T with traffic

FEDERAL COMMUNICATIONS COMMISSION (FCC) STATEMENTS
The user shall not make any changes or modifications to the equipment unless authorized by the Installation Instructions or
User's Manual. Unauthorized changes or modifications could void the user's authority to operate the equipment.
FCC CLASS B STATEMENT
This equipment has been tested to FCC requirements and has been found acceptable for use. The FCC requires the
following statement for your information:
This equipment generates and uses radio frequency energy and if not installed and used properly, that is, in strict
accordance with the manufacturer's instructions, may cause interference to radio and television reception. It has been type
tested and found to comply with the limits for a Class B computing device in accordance with the specifications in Part 15 of
FCC Rules, which are designed to provide reasonable protection against such interference in a residential installation.
However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause
interference to radio or television reception, which can be determined by turning the equipment off and on, the user is
encouraged to try to correct the interference by one or more of the following measures:
• If using an indoor antenna, have a quality outdoor antenna installed.
• Reorient the receiving antenna until interference is reduced or eliminated.
• Move the radio or television receiver away from the receiver/control.
• Move the antenna leads away from any wire runs to the receiver/control.
• Plug the receiver/control into a different outlet so that it and the radio or television receiver are on different branch circuits.
• Consult the dealer or an experienced radio/TV technician for help.
INDUSTRY CANADA CLASS B STATEMENT
ICES-003 Class B Notice - Avis NMB-003, Classe B
This Class B digital apparatus complies with Canadian ICES-003.
Cet appareil numérique de la classe B est conforme à la norme NMB-003 du Canada.
FCC / IC STATEMENT
This device complies with Part 15 of the FCC Rules, and RSS 210 of IC. Operation is subject to the following two conditions:
(1) This device may not cause harmful interference (2) This device must accept any interference received, including
interference that may cause undesired operation.
Cet appareil est conforme à la partie 15 des règles de la FCC & de RSS 210 des Industries Canada. Son fonctionnement est
soumis aux conditions suivantes: (1) Cet appareil ne doit pas causer d' interferences nuisibles. (2) Cet appareil doit accepter
toute interference reçue y compris les interferences causant une reception indésirable.

RF Exposure
WARNING: The communications module must be installed to provide a separation distance of at least 20 cm
from all persons.
WARRANTY INFORMATION
For the latest warranty information, please visit:
www.honeywell.com/security/hsc/resources/wa
2 Corporate Center Drive, Suite 100
P.O. Box 9040, Melville, NY 11747
Copyright © 2011 Honeywell International Inc.
www.honeywell.com/security
Ê800-10344zŠ
800-10344 12/11 Rev. A