Honeywell HumidiPRO H6062A1000/U User manual

HumidiPRO H6062
Digital Humidity Control
Installation
Instructions

2
When Installing this Product
Read these instructions carefully, failure to follow them could damage the product and
cause a hazardous situation.
Check the ratings given in the instructions and on the product to make sure the
product is suitable for your application
Installer must be a trained, experienced service technician.
After installation is complete, check out product operation as provided in these
instructions.
Cautions
Electrical shock or equipment damage may occur.
Disconnect power supply before beginning installation.

3
Duct Installation (recommended) OR
1. Choose a location on the RETURN
duct.
Remote Mount Installation
1. Choose a location in the living area.
NOTE: Select a location clear of drafts
or excessive humidity. Avoid mounting
near doors or windows, or in bathrooms
or kitchens.
ALTERNATE
LOCATION
RETURN
AIR RETURN
AIR
6 IN (152 MM)
MINIMUM
15 IN (381 MM)
MINIMUM
BEST
LOCATION
RETURN
AIR DUCT M34579
YES NO
NO
M34567
Warning: Product must be mounted
on the RETURN side of the duct for
proper RH% sensing.

4
Duct-Mount Installation
2. Separate wallplate from humidistat.
-
3ETTING
,IGHT
!UTO . EXT!UTO
3YSTEM

2EPLACE"ATT
)NSIDE 
(5-)$)49"//34
05,,(%2%
Caution: Electrical Hazard
Can cause electrical shock or equipment damage.
Disconnect power before beginning installation.
3. Mark the duct-tube hole.
Hold the wallplate up to the desired
location on the duct and make a mark
inside the duct tube hole.
M34580

5
4. Drill the duct-tube hole.
Find your mark and drill a 1/2 in. hole in
the duct. This is where the duct tube will
be inserted to capture air.
M34581
5. Insert the duct tube.
M34671
Insert the duct tube through
the wallplate before securing
to the duct.

6
6. Secure the wallplate.
M34582
M34610
RUN WIRES
THROUGH THE
TOP OR BOTTOM
CHANNEL
C
R
U
U
S
S
Secure the wallplate to the duct with
sheet metal screws (provided).
7. Run wires through the back plate.
Run wires through the top or bottom
channel on the back plate when duct-
mounted. If installing like a thermostat on
a wall, run the wires through the back.

7
Wiring the Humidistat
This humidity control is wired the same way a manual humidistat (H8908) is wired. The
only difference is that you also wire in power (24 VAC) and an outdoor sensor.
M34569
TERMINAL DESIGNATION
C 24 VAC POWER FROM EQUIPMENT
R 24 VAC POWER FROM EQUIPMENT
U HUMIDIFIER/DEHUMIDIFIER
U HUMIDIFIER/DEHUMIDIFIER
S OUTDOOR SENSOR
S OUTDOOR SENSOR
NOTES: C AND R MUST BE CONSTANT 24VAC! RECOMMENDED TO WIRE TO
FURNACE/AIR HANDLER CONTROL BOARD.
DO NOT WIRE C AND R TO HUMIDIFIER TRANSFORMER!
C
R
U
U
S
S
24 VAC (CONSTANT)
TO HUMIDIFIER
OR DEHUMIDIFIER
OUTDOOR
TEMPERATURE
SENSOR

8
Wiring HumidiPRO with Fan Interlock
M34570
1
TRANSFORMER
FURNACE
FAN
MOTOR
FAN CONTROL
L1
(HOT)
L2
POWER
SUPPLY
1
2
PROVIDE DISCONNECT MEANS AND
OVERLOAD PROTECTION AS REQUIRED.
24 VAC WIRING.
HUMIDIFIER
2
C
R
U
U
S
S
24 VAC (CONSTANT)
OUTDOOR SENSOR

9
Wiring HumidiPRO with Fan Interlock for 2 Speed Motor
M34571
1
TRANSFORMER
2-SPEED
FAN MOTOR
FAN CONTROL
L1
(HOT)
L2
POWER
SUPPLY
1
2
PROVIDE DISCONNECT MEANS AND OVERLOAD PROTECTION AS REQUIRED.
24 VAC WIRING.
HUMIDIFIER
2
C
R
U
U
S
S
24 VAC (CONSTANT)
OUTDOOR SENSOR
DPST
SWITCHING
RELAY
HL
C

10
Wiring HumidiPRO with Current Sensing Relay
M34572
1
L1
(HOT)
L2
1PROVIDE DISCONNECT MEANS AND OVERLOAD PROTECTION AS REQUIRED.
HUMIDIFIER
C
R
U
U
S
S
24 VAC (CONSTANT)
OUTDOOR SENSOR
CURRENT
SENSING
RELAY
CHI
LO