Honeywell Ex-Or Mid-Bay MS1200DIMBW Installation and operation manual

Mid-Bay: MS1200DIMBW for DSI ballasts
MS1200DALIMBW for DALI ballasts
Hi-Bay: MS1200DIHBW for DSI ballasts
MS1200DALIHBW for DALI ballasts
Mid-Bay & Hi-Bay LightSpot Luminaire Controllers
Note: HP2000 (or HP10*/HP18*) required for commissioning
HC5, HC6 or HP18 required for user override
* Please note that the HP10 and HP18 offer different/limited programming options
Installation and Commissioning
Instructions

43.5mm sq
50mm sq
6.5 mm
32.5 mm
26 mm
Polarity-free
digital output.
Connection to
ballast only.
Do not connect
to other detectors.
Red - Live
Blue - Neutral
Yellow
Green
750mm
lead
Electrical Connections
Only suitably qualified personnel should install this equipment.
Mounting Details
C
L
Cable entry point
14.5mm
C
L
14.5mm
20.3mm
Mid-Bay & Hi-Bay LightSpot Luminaire Controllers
Installation
Snap-in to infill panel (max 0.7mm/ 22 SWG) or use any combination of fixing holes on rear. Use only No 4
type B ºinch self-tapping screws. Ensure that projection of screws into pilot holes does not exceed 4.5mm.
The recommended position for the detector is in the middle of the luminaire. Where this is not possible and the
detector is fitted near one end of the lamps, please ensure that the detector is at the ‘cold’ end of the lamps.
In order to achieve satisfactory light-level regulating operation, a detector must observe a substantially greater
proportion of artificial light from the luminaire(s) under its control than from neighbouring luminaires not under its
control. This is particularly important when planning the installed layout of linear luminaires that have an
integral detector positioned at one end.
To Test Luminaire Controller Operation
Once the Luminaire Controllers have been installed within the luminaires, the HC5, HC6 or HP18 may be used
to switch luminaires ON and OFF. Luminaires with regulating ballasts will also dim and brighten.

Commissioning with HP2000
(HP10 or HP18 can also be used but do not give access to the full range of features)
It is important that the HP2000 be held perpendicular and at a distance of between 0.5m and 2m from the detector.
1. Switch on HP2000 by pressing the red power button.
2. Point HP2000 at detector and press the DOWNLOAD button. The HP2000 will confirm the product’s identity,
and call up the correct menu of parameters and their current settings. It will also show the ballast type and the
duration (shown in hours) remaining on the 100-hour burn-in.
3. Use a combination of UP, DOWN, FORWARD and BACK buttons to navigate the parameter menu, selecting
options for each shown. (See Tips below.)
4. When options for all parameters have been selected, point the HP2000 at the detector and press the UPLOAD
button. The luminaire(s) will switch off briefly during the programming process and the HP2000 shows DATA
OK to confirm operation.
5. After a short period of inactivity (default 5 minutes), the HP2000 hibernates retaining the most recent settings.
Tips
i) Where there are only two options such as ON/OFF, a double click of the OK button toggles between them.
ii) Where there are multiple options, a double click of the OK button recalls a list of all options for that parameter.
Use the UP, DOWN and OK buttons to select.
iii) Use the OK button to go forward (through the menus) without displaying help pages.
iv) Press UPLOAD at any time to transfer all current settings from the handset to the product.
Please refer to HP2000 instructions for comprehensive commissioning details.
Factory Default Settings
These are the settings to which the units have been programmed before they leave the factory:
W5099B
Parameter Options Default
Power Up On / Off On
Response Auto / Semi-Auto Auto
1 min - 96 hrs, 10-sec (walk-test), Disabled (via HP2000)
5-35 mins (in 5 minute increments), walk-test (via HP10)
5, 10 or 20 mins, walk-test (via HP18)
On Sensitivity 0-100 100
Start Lamps Max / Min Max
Entry Scene 1-6 1
Bright Out Yes / No No
Dimming Reg 50%-Reg100% Reg 100%
Lamp Max 10%-100% 1
Fade to Off Yes / No No
When Vacant 10 Exit Scenes Off
Set-Point High 0-1023 1023
Set-Point Low 0-1023 1023
100 Hour Burn-In See Application Note: AN4028 0 hr
Additional feature accessible under Utilities:
Off Delay 20 mins

Technical Data
OPERATING VOLTAGE: 230V 50Hz (UK & Europe)
CAPACITY: Digital DSI - 4 ballasts max
DALI - 1 ballast max
COLOUR: White bezel
MATERIAL: Flame retardant PC/ABS
WEIGHT: 50g
IP RATING: 4X
o o
OPERATING TEMPERATURE: 0 C to 55 C
W5099B
At the end of their useful life
the packaging and product
should be disposed of via a
suitable recycling centre.
Do not dispose of with normal
household waste.
Do not burn.
Ex-Or
Novar ED&S LImited
Haydock Lane, Haydock, Merseyside WA11 9UJ
Tel: [phone]
Fax: [phone]
Email: [e-mail]
www.ex-or.com
Important Additional Notes
1. Ameans for disconnection must be incorporated in the fixed wiring in accordance with the current wiring regulations.
2. Although nominally 12V, the dimming output is not SELV and therefore should be treated with the same respect as mains
with regard to wiring practice. The 0V line of the dimming output is almost at Neutral potential.
3. The dimming control output should be connected only to the control input of the ballasts - never to other detectors.
4. This equipment should be used to control only those ballasts powered from the same phase as the detector.
5. Due to the fact that the photocell is on the ceiling looking down, it is not possible for measurements made with a lux meter on
the working plane to remain constant when daylight illuminates the ceiling and the working plane to a differing extent.
Therefore, products of this type should be regarded as capable of maintaining anAPPROXIMATE light level only.
6. In order to achieve satisfactory light level regulating operation, a detector must observe a substantially greater portion of
artificial light from the luminaire(s) under its control than from neighbouring luminaires not under its control. This is particularly
important when planning the installed layout of linear luminaires that have an integral detector positioned at one end.
7. The recommended position for the sensor is in the middle of the luminaire. Where this is not possible and the sensor is fitted
near one end of the lamps, please ensure that the sensor is at the “cold” end of the lamps.
8. This equipment switches lights no more frequently than would a responsible human occupant. However, manufacturers of
some particular lighting types (e.g. ‘2D’ luminaires) may specify a maximum number of switching cycles in order to achieve a
predicted lamp life. Please check with the manufacturer of the luminaires to ensure that they are compatible with automatic
controls in this respect.
h
d
Mid-Bay:
MOUNTING HEIGHT: 12.0m max
RANGE: Cone-shaped detection pattern,
diameter at floor level (d) = 1.75 x mounting height (h)
Hi-Bay:
MOUNTING HEIGHT: 16.0m max
RANGE: Cone-shaped detection pattern,
diameter at floor level (d) = 1 x mounting height (h)
h
d