Honeywell Temaline TS2 User manual

Installation Manual
Temaline
TS2 (TemaServer 2)

ii https://extranet.honeywell.com
Notice
This document contains Honeywell proprietary information. Information contained
herein is to be used solely for the purpose submitted, and no part of this document or
its contents shall be reproduced, published, or disclosed to a third party without the
express permission of Honeywell Europe.
This document and the data in it shall not be duplicated, used or disclosed to others
for procurement or manufacturing, except as authorized by and with the written
permission of Temaline, Inc. The information contained in this document or in the
product itself is the exclusive property and trade secrets of Temaline, Inc.
Copyright laws of the United States protect all information in this document or in the
software product itself.
While this information is presented in good faith and believed to be accurate,
Honeywell disclaims the implied warranties of merchantability and fitness for a
purpose and makes no express warranties except as may be stated in its written
agreement with and for its customer.
In no event is Honeywell liable to anyone for any direct, special, or consequential
damages.
The information and specifications in this document are subject to change without
notice.
Trademarks
Tema-VoyagerTM is a trademark of Honeywell International Inc.
MIFARE® is a registered trademark of Philips Electronics N.V.
HID is a trademark or registered trademark of HID Global Corporation.
LonWorks® is a registered trademark of Echelon Corporation.
Any other trademarks that appear in this document are used only to the benefit of the
trademark owner, with no intention of trademark infringement.
Compliance
To obtain applicable EU compliance Declaration of Conformities for this product,
please refer to our website, https://extranet.honeywell.com. For any additional
information regarding the compliance of this product to any EU-specific
requirements, please send email to [email protected]
Single contact point and Support
Manufacturer’s single point of contact:
Honeywell S.r.l.
Via Philips, 12
20052 Monza
ITALY
For technical assistance, call your nearest Honeywell office.
Document Release Issue Date
800-22710 2.2 H November 2017

iii
TABLE OF CONTENTS
INTRODUCTION................................................................................................................................................... 4
Purpose of this manual ..................................................................................................................................4
What TS2 is?.................................................................................................................................................. 4
System Architecture....................................................................................................................................... 4
Device components........................................................................................................................................5
Related documentation.................................................................................................................................. 6
PREPARING FOR INSTALLATION ..................................................................................................................... 7
Contents of the kit..........................................................................................................................................7
Optional Parts...........................................................................................................................................7
Spare Parts...............................................................................................................................................7
Mounting tools................................................................................................................................................ 7
Wires Characteristics..................................................................................................................................... 8
Power supply wire..................................................................................................................................... 8
LONWORKSData Cables...................................................................................................................... 8
MOUNTING THE DEVICE .................................................................................................................................. 10
Dimensional requirements............................................................................................................................ 10
Attaching the Device Support Plate.............................................................................................................. 10
Hooking Up the device................................................................................................................................. 11
CONNECTING THE CABLES ............................................................................................................................ 13
Connecting the DC Power Supply................................................................................................................ 14
Connecting the LONWORKS Cable............................................................................................................. 15
Connecting the network cable...................................................................................................................... 16
Connecting the battery................................................................................................................................. 18
FINAL OPERATIONS......................................................................................................................................... 19
Closing the Terminal.................................................................................................................................... 19
Commissioning tips...................................................................................................................................... 19
Configuring the TemaServers................................................................................................................. 19
Factory default IP Address...................................................................................................................... 19
Factory FW version................................................................................................................................. 20
TS2 DEVICE ANATOMY .................................................................................................................................... 21
TS2 Main board - Switches and LEDs ......................................................................................................... 23
Device Configuration Jumpers..................................................................................................................... 24
TS2 Lonwork Xboard - Jumpers and Switch................................................................................................ 26
TS2 LonWorks Xboard - diagnostic and MIP LEDs...................................................................................... 26
Device Tampers........................................................................................................................................... 28
Anti open tamper .................................................................................................................................... 28
External tampers connection .................................................................................................................. 28
OPERATING INSTRUCTIONS & MAINTENANCE ............................................................................................ 30
Reset the TS2 device................................................................................................................................... 30
Switch off the TS2 device............................................................................................................................. 30
TS2 application quick health check.............................................................................................................. 30
TS2 Cable Fuse replacement....................................................................................................................... 32
TS2 Battery replacement ............................................................................................................................. 32
CONDITIONS RESULTING IN IMPAIRED OPERATION................................................................................... 34
PROTECTIVE FEATURES (WARNING OF BYPASSING) ................................................................................ 35
TECHNICAL SPECIFICATIONS......................................................................................................................... 36
REGULATIONS.................................................................................................................................................. 37

iv https://extranet.honeywell.com
CE Compliance............................................................................................................................................ 37
“Access Control System for use in Security Applications” Compliance........................................................ 37
Canadian and United States UL Listed........................................................................................................ 38
FCC Notice................................................................................................................................................... 38
RoHS compliance ........................................................................................................................................ 39
WEEE compliance ....................................................................................................................................... 39
China RoHS declaration............................................................................................................................... 39
Appendix 1 – Meaning of graphical symbols used ........................................................................................ 41

1
Warnings and Cautions
Before installation
Warning: Before installation, TURN OFF the external circuit breaker which supplies
power to the device.
Before connecting the device to the power supply, verify that the output voltage is
within specifications of the power supply. (See “Technical specifications” on page
37.)
Do not apply power to the device until after the installation has been completed.
The equipment can be damaged if this precaution is not observed.
Fire Safety and Liability Notice
Warning: Never connect card readers to any critical entry, exit door, barrier, elevator or
gate without providing an alternative exit in accordance with all the fire and life
safety codes pertinent to the installation.
These fire and safety codes vary from city to city and you must get approval from
local fire officials whenever using an electronic product to control a door or other
barrier. Use of egress buttons, for example, may be illegal in some cities. In most
applications, single action exit without prior knowledge of what to do is a life safety
requirement. Always make certain that any required approvals are obtained in writing.
DO NOT ACCEPT VERBAL APPROVALS SINCE THEY ARE NOT VALID.
Damage during shipment
Caution: IF ANY DAMAGE TO THE SHIPMENT IS NOTICED, A CLAIM MUST
BE FILED WITH THE COMMERCIAL CARRIER RESPONSIBLE FOR THE
DAMAGE.
Electrostatic discharge
Caution: Electrostatic discharge (ESD) can damage integrated circuits and modules. To
prevent damage always follow these procedures:
Use static shield packaging and containers to transport all electronic components,
including completed reader assemblies.
Handle all ESD sensitive components at an approved static controlled workstation.
These workstations consist of a desk mat, floor mat and an ESD wrist strap.
Workstations are available from various vendors.
Note: This equipment generates, uses, and can radiate radio frequency energy and, if
not installed and used in accordance with the installation and user guides, may cause
harmful interference to radio communications. Operation of this equipment in a
residential area is likely to cause harmful interference in which case the user will be
required to correct the interference at his own expense.
Disclaimer – Product Liability; Mutual Indemnification
If a Customer receives a claim that a Product or any component thereof has caused
personal injury or damage to the property of others, Customer shall immediately
notify Honeywell S.r.l. Italy in writing of all such claims. Honeywell S.r.l. Italy shall

2https://extranet.honeywell.com
defend or settle such claims and shall indemnify and hold Customer harmless for any
costs or damages including reasonable attorneys’ fees which Customer may be
required to pay as a result of the defective Product or the negligence of Honeywell
S.r.l. Italy, its agents, or its employees.
Customer shall hold harmless and indemnify Honeywell S.r.l. Italy from and against
all claims, demands, losses and liability arising out of damage to property or injury to
persons occasioned by or in connection with the acts or omissions of Customer and its
agents and employees, and from and against all claims, demands, losses and liability
for costs of fees, including reasonable attorneys’ fees, in connection therewith.
Compliance
For any additional information regarding the compliance of this product to any EU-
specific requirements, please send an e-mail to [e-mail].
Unpacking
Caution: If any damage to the shipment is noticed before unpacking, a claim must be
filed with the commercial carrier.
All containers should be opened and unpacked carefully in order to prevent damage to
the contents.
Follow these steps to unpack equipment in preparation for installation:
Open the container and remove the unit(s) and all packing material. Retain the
container and all the packing materials. They may be used again for reshipment of the
equipment, if needed.
Inspect the contents to see if anything is missing. If you notice any missing items,
send an e-mail to [e-mail].
Visually check the contents. If you see any damage, do the following:
If shipping has caused damage to the unit, file a claim with the commercial carrier.
If any other defect is apparent, call for a return authorization.
Shipping instructions
To ship equipment back to Temaline, contact the customer service department at
[e-mail] before returning the equipment. When you call, please
have available:
A description of the problem or the reason you are returning the equipment.
Your original purchase order number, invoice number and if the unit is still under
warranty.
A new purchase order number if the unit is not under warranty.
From the customer service department, obtain the Return
MerchandiseAuthorization (RMA).
Show the RMA number on all packages shipped. Packages which are not marked with
an RMA number will be refused at the factory and returned to you COD.
Carefully pack the equipment for shipment. Use the original packing material
whenever possible
Limited warranty
All warranty work shall be handled through Customer who shall notify Temaline and
apply for a Return Merchandise Authorization (RMA) number prior to returning any

3
Product for service, repair, credit or exchange. Temaline warrants that its Products
shall be free from defects in materials and workmanship for a period of 18 months
from the date of shipment from the Temaline warehouse. Satisfaction of this warranty
shall be limited to repair or replacement of Products which are defective or defective
under normal use. Temaline’s warranty shall not extend to any Product which, upon
examination, is determined to be defective as a result of misuse, improper storage,
incorrect installation, operation or maintenance, alteration, modification, accident or
unusual deterioration of the Product due to physical environments in excess of the
limits set forth in Product manuals. THERE ARE NO WARRANTIES WHICH
EXTEND BEYOND THIS PROVISION. THIS WARRANTY IS IN LIEU OF ALL
OTHER WARRANTIES WHETHER EXPRESS, IMPLIED OR STATUTORY,
INCLUDING IMPLIED WARRANTIES OF MERCHANTABILITY OR FITNESS
FOR ANY PARTICULAR PURPOSE. NO REPRESENTATION OR WARRANTY
OF THE DISTRIBUTOR SHALL EXTEND THE LIABILITY OR
RESPONSIBILITY OF THE MANUFACTURER BEYOND THE TERMS OF THIS
PROVISION. IN NO EVENT SHALL TEMALINE BE LIABLE FOR ANY RE-
PROCUREMENT COSTS, LOSS OF PROFITS, LOSS OF USE, INCIDENTAL,
CONSEQUENTIAL OR SPECIAL DAMAGES TO ANY PERSON RESULTING
FROM THE USE OF TEMALINE’S PRODUCTS.
Confidentiality
All software, drawings, diagrams, specifications, catalogs, literature, manuals and
other materials furnished by Honeywell HSG –Temaline relating to the design, use
and service of the Products shall remain confidential and shall constitute the
proprietary rights of Honeywell HSG -Temaline and Customer agrees to treat such
information as confidential.
Customer shall acquire no rights in the design of the Products or the related materials
except to use such information solely for the purpose of and only during the time it
sells the Products. Customer shall not copy the design of any of the Products or use or
cause to be used any Product design or related materials for its own benefit or for the
benefit of any other party. The covenants contained in this section shall remain
effective throughout the term of this Agreement and thereafter unless specifically
waived by Honeywell HSG -Temaline in writing.

4https://extranet.honeywell.com
INTRODUCTION
Purpose of this manual
This manual details how to install and maintain a TS2 device.
Details on operating instruction, plant maintenance and
troubleshooting are also provided.
What TS2 is?
TS2 is a Temaline device acting as controller in the Temaline
architecture.
TS2 managed applications include: Access Control,
Time&Attendance, Canteen, light Intrusion detection and Lift.
It can manage up to 16 doors (with reader on a single side of the
door or with reader on both sides of the door.
It can also manage up to 64 supervised inputs and 64 Digital
Output.
It is connected to the Supervisor via Ethernet line. It manages all
the field devices via LonWorks bus.
System Architecture
Figure 1 shows a typical system architecture in which the TS2 is
inserted.
Other devices represented are:
•TemaPower: is the power supply used to supply the
devices. It can be one Temaline TPU-xx device or a third
party power supply.
•Temaline RTU devices: Fields devices used for the
management of the doors.
The connections shown are:
•The Ethernet connection: it connects EBI supervision
center with all the peripheral devices and peripheral device
in peer to peer.
•The Power supply connection: it connects the Power
Supply device with other Temaline devices.

5
•The Lonwork connection: to connect TS2 with Temaline
field devices (RTUs).
Figure 1 – TS2 typical system architecture
Device components
This chapter gives an overview of the components of TS2 device;
the intent is to provide the main terms used into the installation
phase.
For a more deep understanding of the device please refer to the
chapter TS2 DEVICE ANATOMY on page 21.

6https://extranet.honeywell.com
Figure 2 - TS2 components overview
Related documentation
Document Content
EBI -
Temaline Access
Control Configuration
Guide
Further information on the EBI
Tema system
, complete
commissioning steps and
system configuration are
included in the,
which is
provided with EBI
documentation package.
TS2 Web interface User manual of the TS2 Web
Interface used for
commissioning and
maintenance operations.
Temaline -
installation in
Harsh Environment: Ii is a whitepaper with Temaline system rules on the topic.

7
PREPARING FOR INSTALLATION
Contents of the kit
Before you begin, unpack the shipment and check the parts list
against the components in the shipment.
Your shipment should contain:
•TS2 device
•Metal Device Support Plate.
Into the device are housed:
•+12V connector
•LonWorks connector
•Battery 6V 1.2 Ah (not wired)
Optional Parts
It is possible to order following optional parts for this device:
Code Item
TSACC01 TORX T10 screwdriver
Spare Parts
It is possible to order following spare parts for this device
Code Item Details
1801026 Battery 6V 1.2 Ah
1520185 TS2 LonWors Xboard Plug-in for Lon connection
1700237 Fuse F1 3A 250V delayed (5X15 UL omega) wired
Mounting tools
The following screwdrivers are required for the installation:
•3mm slotted screwdriver
•3mm cross screwdriver
•5mm cross screwdriver
•T10 Torx screwdriver

8https://extranet.honeywell.com
Wires Characteristics
Use this chapter to understand the type of wire you need to use
for your plant.
Power supply wire
The TemaServer is powered at low voltage (12VDC±20% 600mA).
It can be powered at low voltage (12VDC 600mA) by Temaline
TPU03 battery-operated power supply module or by a vendor
power supply with same characteristics.
In order to determine the correct size for power cables, refer to the
below table
Make sure that the 12V cable corresponds in size to the norms
indicated in the table below (voltage cable drop max = 2V):
Cable length (m) = 2V / (0.6A x 2 x (res [Ohm/km] /1000))
Type of cable Length (m)
AWG mm2 Ohm/Km 600 [mA]
10 5.25 3.41 489
12 3.3 5.7 278
14 2 8.8 189
16 1.3 14 119
18 0.9 21 79
20 0.6 34 49
22 0.35 52 32
Table 1 - Length of Power Cables (m)
LONWORKS

Data Cables
Data cables used with LonWorks®must be twisted-pair.
In a free-topology configuration or star connection, where all
device are connected starting from one single point, the total sum
of the cable lengths must not exceed 500m.
In a bus configuration or daisy chain configuration, where a device
is connected to the previous one, the bus length must not exceed
2700m.
Refer to Table 2.for sizing data cables to be used for LonWorks®
connection.
Type of cable Length [m] in relation to cable capacity
AWG mm2 Ohm/Km 50nF/Km 100nF/Km 200nF/Km 500nF/Km 1uF/Km
12 3,3 5,7 2676 1892 1338 846 598

9
14 2 8,8 2153 1523 1077 681 482
16 1,3 14 1707 1207 854 540 382
18 0,9 21 1394 986 697 441 312
20 0,6 34 1096 775 548 346 245
22 0,35 52 886 626 443 280 198
24 0,2 85 693 490 346 219 155
Table 2 - Length/Capacity of LONWORKS

Data Cables (m)
The FTT10A Echelonv1.2 User Guide recommends the cables
indicated in Table 3
Producer and Model AWG Bus
Connection
Maximum total
length [m]
Free topology
Connection
Maximum node-
node length. [m]
Free topology
Connection
Maximum
total wire
length. [m]
Belden 85102 16 2700 500 500
Belden 8471 16 2700 400 500
Level IV (twisted-pair,
typically solid and
unshielded)
22 1400 400 500
JY (St) 2x2x0.8 (4-
wire helical twist, solid
shielded)
20 900 320 500
TIA Cat5 / 900 250 450
Table 3 - Recommended LONWORKS

Cables

10 https://extranet.honeywell.com
MOUNTING THE DEVICE
Dimensional requirements
Installation of TS2 is wall-mounted. It is recommended that you
attach the cables to an encased box. The position selected for
mounting the box must satisfy the requirements established for the
mounting area and must allow the necessary space for opening
the box (see Figure 3). In addition, there must be sufficient space
around the bottom of the unit and to the right to allow you to
access the box with a screwdriver.
Figure 3 Space Requirements for Mounting
Attaching the Device Support Plate
To attach the device support plate, drill two holes into the wall, into
which to introduce the M6 screws and plastic dowels that are to
hold up the support plate (see Figure 4). Make sure that the
support plate attached to the wall is aligned with the niche on
the lower part of the support plate (use a ∅5mm cross
screwdriver).

11
Figure 4 - Support Plate
Hooking Up the device
To hook up the device to the wall, follow these steps (see Figure
5): 1. Attach the upper part of the device to the upper hooks on
the support plate.
2. Insert the cables into the device through the specified
openings.
3. Tighten the two screws that secure the device to the
support plate (use a ∅5mm cross screwdriver).

12 https://extranet.honeywell.com
Figure 5 - Hooking Up the Terminal

13
CONNECTING THE CABLES
Cables to be connected are (see Figure 6):
•DC power supply
•LonWorks (RTUs connection)
•Ethernet (10/100BaseT)
•Battery
Figure 6 - Connecting the Cables
To connect the cables, follow these steps:
1. Connect all the cables to the board (see below details).
2. Line up the cables with the grooves at the back of the
terminal and screw in the cable fixing plate that is used as a
cable clamp (use a ∅5mm cross screwdriver).
Tip: Place the cables in the lower lateral grooves, so that they are
not forced to negotiate tight bends.

14 https://extranet.honeywell.com
Caution:
All the cables shall be separated at least 0.25
inches (10mm) from the battery wire
Connecting the DC Power Supply
From factory is plugged on J1 connector a polarized indirect screw
connector.
Attach the ends of the DC Power supply cable heads onto the
indirect screw connector provided together with the device (use a
∅3mm slotted screwdriver).
Figure 7 - DC Power Supply J1 connector
The J1 connector is provided of a polarized indirect screw
connector with the following connection characteristics:
•Conductor section AWG min = AWG24 max = AWG13
•Conductor section rigid or flexible min = 0.2 mm2max = 2.5
mm2
Check: Once the DC Power Supply is properly
connected and switched on the CR2 Green Led
(+12VDC main power) present on the TS2 main
board must be in ON status.

15
Figure 8 - CR2 Led position on main board
Connecting the LONWORKS Cable
From factory is plugged on J6 connector an indirect screw
connector.
Attach the ends of the LonWork cable heads onto the indirect
screw connector provided together with the device (use a ∅3mm
slotted screwdriver). The polarity of the LonWorks®cables is not
significant.
Figure 9 - J6 connector on LonWorks Xboard
The indirect screw connector has the following connection
characteristics:
•Conductor cross section AWG min = AWG30 max =
AWG14
•Conductor cross section flexible min = 0.05 mm2 max = 1.5
mm2
•Conductor cross section rigid min = 0.05 mm2max = 2.5
mm2

16 https://extranet.honeywell.com
If LonWorks is in free topology configuration, activate the 51
ohm terminator by closing the JP1 on the Lonwork Xboard.
if two TS2 are connected on the same channel (shared load
configuration) insert JP1 just in one device.
If LonWorks is in bus configuration, place two terminators (with
resistance values of 100ohm 1% ½W) at each end of the bus and
remove (if it is present) the terminator for free topology
configuration by opening the JP1 on the Lonwork Xboard.
if two TS2 are connected on the same channel (shared load
configuration) remove JP1 from both the devices.
Check1: Once the LonWorks bus is properly
connected and the TS2 switched on the DL4 yellow
Led (LonWorks service) must be OFF and the DL5
Green Led (LON/MIP Communication activity) must
blink regularly. The two led are located on
LonWorks Xboard.
Figure 10 - DL4 and DL5 Led positions on LonWorks XBoard
Check2: Once the LonWorks bus is properly
connected, the RTUs wired and the TS2 switched on
use the RTU Service button to verify if the LonWorks
is properly connected. See RTU installation guides
to know where the Service button is located.
Connecting the network cable
The network cable must be a 10/100 BaseT standard unshielded
CAT5 cable terminated with an RJ45 male connector.
It needs to be plugged on T1 connector.