Honeywell JTQJ-BF-01LM/BW User manual

Honeywell GAS DETECTOR
The autonomous gas sensor (hereinafter referred to as the sensor) is a home
device for detecting a leak of natural gas (the main component is methane),
which, in the case of determining a high concentration of combustible gas
(methane) in the room, produces a light-sound alarm or sends a warning message
to the connected device.
Overview
Accessories
Alarm x1
Mounting plate x1
Battery x1
Holes for sound
«Sound/Self control» button Holes for detecting a gas
The instruction x1
Plug dowel x2
Screw x2
Double-sided adhesive tape x2
Setup instructions
1. Connection terminal, output signal and device connection
* Even if the connection terminal is not connected to the device, the sensor will still
function.
* If you need to connect an electromagnetic solenoid valve or an output fan to the
wiring, please ask your dealer for assistance.
Сonnection terminal

Installation
1. Fastening with screws
a) Insert the battery into the battery compartment, press and hold the «Sound /
Self-check» button for 1 second. Make sure that the red-yellow indicator starts
ashing on the device, after which you will hear a corresponding beep.
b) Drill holes in the ceiling with a perforator;
c) Insert the dowels;
d) Using self-tapping screws, attach the mounting plate;
e) Attach the main alarm panel to the mounting panel in accordance with all the
index marks, go clockwise until you hear a characteristic click that indicates the
xation of the device.
Using self-tapping screws, install the mounting plate.
Attach the main alarm panel to the mounting panel in accordance with all the
indicia.
Turn clockwise until it clicks.
2. Mounting with adhesive tape
a) Insert the battery into the battery compartment, press and hold the «Sound /
Self-check» button for 1 second. Make sure that the red-yellow indicator starts
ashing on the device, after which you will hear a corresponding sound signal
b) Remove the protective lm from one side of the adhesive tape and attach it to
the back of the mounting panel;
c) Remove the protective lm from the other side of the adhesive tape and attach
Precautions for installation
a. Install the device in the premises where the gas (methane) is conducted;
b. Avoid places outside the premises;
c. Avoid rooms with a temperature below -10 ° C or above 55 ° C;
d. Avoid places near other devices, that produce hot air, water vapor or soot (for
example, directly above the gas stove);
e. There should be no barrier between the sensor and the gas equipment,
otherwise the sensor will not be able to measure the gas concentration level;
f. Avoid places at the hood, windows, entrance doors and other well-ventilated
places, otherwise the sensor will not have contact with the gas and will not be
able to measure its concentration level;
g. Make sure all sockets are plugged in;
h. It is recommended to perform the installation with screws, in the case of
installation with adhesive tape, unforeseen situations may occur, the user is
responsible for;
i. If installed with adhesive tape, make sure that the selected surface for attaching
the device is smooth, smooth, clean and dry;
j. If installed with adhesive tape, it is necessary to regularly check the reliability of
the fastening to prevent the sensor from falling.
the mounting plate to the ceiling;
d) Attach the main alarm panel to the mounting panel in accordance with all the
reference marks, go clockwise until you hear a characteristic click that indicates
the xation of the device.

Using
Functions
Indicator status
Selecting an installation location
Wall mounting: the distance between the gas sensor and the gas equipment or
valve should not be more than 4 meters, the distance from the sensor installation
to the ceiling should be less than 0.3 meters, but do not install the sensor directly
above the gas equipment. Below is a schematic drawing that will help you choose
the right location for the device.
Ceiling installation
The distance between the gas sensor and the gas equipment or valve should not
be more than 4 meters, do not install the sensor directly above the gas equipment.
Below is a schematic drawing that will help you choose the right location for the
device.
1. Power supply for preheating
Before switching on the power, make sure that the power source is operating
properly;
Connect the device to the power supply - the buzzer sounds three times, after
which the red, yellow, green indicator ashes in turn. After about ve minutes,
one long beep will sound, indicating the exit from the preheating mode, the green
indicator will light up.
* When using for the rst time, or if the device has not been used for a long time,
please connect the sensor to the power supply
for 72 hours for further optimal operation of the device.
2. Normal working status
In the absence of malfunctions or an alarm, the green indicator is constantly on;
when the «Sound / Self-diagnosis» button is pressed, the sensor switches to the
self-test mode (once in a row the red, yellow, green indicator ashes, and the
alarm sounds once). After completion of self-diagnosis, the sensor restores normal

Main parameters
operation.
3. Alarm
If the device has no faults, but as a result of exceeding the permissible level of gas
concentration in the room, the audible alarm turns on, the red indicator lights up,
and the signal sounds. To turn o󰀨 the signal, press the «Sound / Self-Diagnosis»
button, and after about 70 seconds the device will resume its operation.
If the gas concentration level is below the maximum permissible value of the
sensor, it automatically switches to normal operation. If other devices are
connected to the sensor, it is necessary to conrm the elimination of a hazardous
situation and restore the gas supply. Reconnect the devices according to the
recommendations in the operating instructions.
4. Fault status
In case of a malfunction, the yellow indicator lights up and a beep sounds, and
two beeps sound every 5 seconds. You can press the «Sound / Self-Diagnosis»
button, after 12 hours the audible alarm will turn on again.
5. Duplicate a signal on another device
If the sensor is operating in normal mode, press and hold the «Sound / Self-
Diagnosis» button for 3 seconds to enter the signal duplication mode. In this case,
the red indicator will light up, a continuous loud beep will turn on. If you press and
hold the «Sound / Self-Diagnosis» button for 11 seconds, an alarm is output to
the connected device. If you release the button, you immediately exit the signal
duplication mode.
Maintenance
To ensure normal operation of the sensor, perform maintenance on the device
following the following recommendations:
1. Install, use and maintain the sensor, following the recommendations in the
manual;
2. It is recommended to perform a self-diagnosis of the device once a month:
press the «Sound / Self-diagnosis» button, make sure that the sensor is
functioning normally;
3. It is recommended to wipe the external surface of the device every season,
clean the air intake openings from dust and grease, make sure that the sensor
holes have good entrance patency, and the alarm system works properly. To clean
the device use a dry towel, do not use alcohol, chemical, other abrasives or too
wet a towel.
4. It is recommended to calibrate once a year.
Calibration should be performed by qualied organizations. Do not perform a
calibration yourself.

Cautions
1. This sensor is used only for pipeline gas (methane), can not be used to
determine liqueed gas in cylinders;
2. It is forbidden to make changes of the internal structure of the device;
3. Do not directly expose the highly concentrated ammable gas to the sensor (eg
lighter gas, clean natural gas, etc.), this may result in a partial / total reduction in
the sensitivity of the sensor or its damage;
4. Avoid a large number of solid aerosols, insecticides, paints, glues, solvents
and other similar substances near the sensor. This can provoke a false alarm and
adversely a󰀨ect the life of the device;
5. The operating life of the internal sensor is 5 years. Please pay attention to
the service life of the device and perform timely maintenance or replacement of
necessary elements;
6. Regularly pay attention to the work of the sensor. In case of a malfunction, do
not disassemble the device yourself. It is necessary to contact the store or the
manufacturer in a timely manner and describe in detail the signs of the problem
so that the after-sales service representative can advise you. If the product needs
to be returned to the factory for maintenance, adhere to the safety practices when
using gas.
Rights and responsibilities of the company
1. This manual contains a detailed description of the rules for using the device, its
technical parameters and other information, but the company reserves the right to
make changes to the manual without further notice;
2. The shown sensor may be slightly di󰀨erent from the actual device, the actual
appearance of the product prevails;
3. This information is intended only for familiarization, it is not a form of obligation;
4. All rights reserved, the company reserves all rights. No part of this manual may
be reproduced in full or in part, copied by any organization or person without prior
written consent and should not be distributed in any form.
Faults and troubleshooting

Actions on gas leakage
1. When the alarm is on, do not turn on any electrical appliances;
2. It is forbidden to disconnect the sensor from the power source, it can
automatically close the solenoid valve and turn on the fan (if it is);
3. It is necessary to disconnect all sources of re, close the gas valve;
4. It is necessary to open windows and doors for ventilation of the room.
The presence of hazardous and noxious substances
adhesive
tape
hard plastic
screws
circuit board
These tables are provided in accordance with SJ / T 11364.
A: Toxic and harmful substances in all components of this device are contained in
an amount below the threshold value according to the standard
GB / T 26572.
X: the presence of toxic and noxious substances in at least one of the
components of this device in an amount exceeding the threshold value, according
to GB / T 26572.
Warranty
Warranty service is carried out in accordance with the law on «Consumer Rights»
and «Product Quality Law». Warranty service includes:
1. Within 7 days from the date of purchase, in case of a problem with the «Fault
list», the Xiaomi Service Center determines the cause of the problem, after which
you can choose a free replacement of the goods, return or repair.
2. Within 8-15 days from the date of purchase, in case of a problem with the
«Fault list», the Xiaomi Service Center identies the problem, after which you
choose a free replacement of the product or service.
3. Within 12 months from the date of purchase, in case of a problem with the
«Fault List», the Xiaomi Service Center determines the problem, after which you
are provided with free repair.
Conditions, that are not covered by warranty service
1. Maintenance of the device in unauthorized service centers, improper use, falls,
negligence, abuse, water a󰀨ects, accident, damage to the label and labeling of the
device;
2. The warranty has expired;
3. Damage caused by force majeure;
4. Breakdowns, that do not correspond to the «List of faults» of the Xiaomi service
center;
5. Breakdown of the device from the «Fault List», which arose in connection with
the human factor and prevent its normal operation.
XIAOMI-MI.COM