Honeywell SEARCHZONE SONIK User manual

QUICK START
GUIDE
HAND HELD TEST TOOL
SEARCHZONE SONIK

3
Figure
1
Figure
2
Figure





 
Negative battery
terminal against
spring
4
Figure
5
Figure
6
Figure 7 Figure

3
Quick Start Guide  ENGLISH
Waste Electrical and Electronic Equipment (WEEE)
This product complies with the Waste Electrical and Electronic
Equipment (WEEE) Directive 2012/19/EU. Components or
assemblies bearing this or similar symbols shall not be treated
as household or municipal waste. Waste electrical products (end of life)
shall be recovered and disposed of at specialist WEEE disposal facilities.
Contact your local authority, your distributor, or the manufacturer if you
require more information about recycling WEEE.
Box Contents
1. Hand Held Test Tool
2. Set of 10 AAA batteries
3. Hexagon socket key size 6 mm
4. Hand Held Test Tool Quick Start Guide (this document)
5. Certificate
List of Markings
Warning
WEEE mark
UL certification mark
Explosive atmosphere class
WARNING
Read these user instructions carefully before using
this equipment. User instructions must always be
available to the user and are not to be removed
except by the user of this equipment. For proper
use, see supervisor, user instructions, or contact
the manufacturer.
WARNING
Do not mix battery types. Replace the batteries only with the types listed
in Specifications. Use of batteries other than those specified in Specifica-
tions will invalidate the certification.

4
European Economic Area certification mark
Environment Friendly Use Period
Intrinsically Safe - À Sécurité Intrinsèque
Cl. I, Div. 1, Grps. A,B,C,D, T4
Cl. I, Zn. 1, AEx ia IIC T4
Ex ia IIC T4
Ta -20°C to +50°C
IP66
Patent: www.hsmpats.com
WARNING/AVERTISSEMENT
Part NO.
Serial NO.
Mod State: 1 2 3 4 5 6 7 8 9 10
Honeywell Analytics Ltd., Poole, Dorset, BH17 0RZ Made in UK
465385
HAND HELD UNIT
TEST TOOL
2331B1000
XXXXXXXXX
Read and understand manual before installation, operation or servicing. Substitution of components may impair intrinsic safety. Do not open or replace battery when an explosive atmosphere is present.
Use only DURACELL MN2400 AAA batteries or equivalent (refer to Quick Start Guide for allowed battery types).
Lire et comprendre le manuel avant d’installer, d’utiliser ou de réparer l’équipement. La substitution des composants peut nuire à la sécurité intrinsèque. N’ouvrez pas l’équipement et ne remplace pas la betterie dans
des atmosphères contenant des explosifs.
Utilisez uniquement des piles AAA DURACELL MN2400 ou équivalentes (reportez-vous au Guide de démarrage rapide pour les types de piles autorisés).
II 2 G
HAND HELD UNIT - TEST TOOL
Ex ia IIC T4 Gb
Ta -20°C to +50°C
DEMKO20ATEX2247
IECEx UL20.0043
IP66
Patent: www.hsmpats.com
2813
Read and understand manual before installation, operation or servicing. Substitution of components may impair intrinsic safety.
Do not open or replace battery when an explosiveatmosphere is pre sent.
WARNING
Part NO.
Serial NO.
Mod State: 1 2 3 4 5 6 7 8 9 10
Honeywell Analytics Ltd., Poole, Dorset, BH17 0RZ Made in UK
Use only DURACELL MN2400 AAA batteries or equivalent (refer to Quick Start Guide for allowed battery types)
2331B1000
XXXXXXXXX
Example certification labels
Example warning label
Instructions
The Hand Held Test Tool is an ultrasound-generating device used for
functional verification of the Searchzone Sonik detector. It may be used in
combination with the Searchzone Sonik App running on a suitable mobile
device.
The Hand Held Test Tool generates two different test signals to check
detector’s functionality:
1) First test signal is recognized by the detector as a ‘bump test’ and is
used to perform the local test. It is reported through change in detector’s
LED ring status indicator, however the detector’s outputs will NOT be
activated. This local test is automatically logged.
2) Second test signal is used for END-toEND testing. It is reported as
Alarm through detector’s LED ring status indicator, relays and through
420mA loop.
WARNING
While operating the Hand Held Test Tool, do not under any circum-
stances aim the tool towards your head, or any other person.
NOTE: When using the Hand Held Test Tool, ensure that it is operated at
least 1m from the Searchzone Sonik detector.

5
Sound pressure levels and usable beam
1. Performing LOCAL Test
WARNING
Do not under any circumstances aim the detector at the head or
ears of you or anyone else.
1.1 Local test with Hand Held Test Tool alone
1. Ensure that Searchzone Sonik is powered and operational.
2. Aim the Hand Held Test Tool towards the face of Searchzone Sonik
detector. Keep the distance between the Searchzone Sonik detector and
the Hand Held Test Tool in the range of 1 to 10 m (3.3 to 33 ft.).

6
3. Press and hold the Test Button (Figure ). The Hand Held Test Tool
will produce audible beeps and show a red LED light to confirm that it is
emitting the test signal.
4. The detector will recognize the test signal and the LED status indicator
will flash red.
5. Release the Test Button. The LED status indicator will return to the
default state (green).
In this mode the outputs are NOT affected.
1.2 Local test with Searchzone Sonik App and Hand Held Test Tool
1. Login to the Searchzone Sonik App.
2. Connect the Searchzone Sonik App to the detector.
3. Navigate to the main menu and tap on Detector Overview. Then tap
on Proof Test.
4. Aim the Hand Held Test Tool to the face of the detector. Keep distance
between the Searchzone Sonik detector and the Test Tool in the range of
1 to 10 m (3.3 to 33 ft.).
5. Press the Test Button (Figure )on the Hand Held Test Tool.
6. The detector will recognize the test signal and LED status indicator will
flash red.
7. While the Test Button is pressed the Searchzone Sonik App will indicate
the test signal as recognized. The test is automatically logged by the
Searchzone Sonik App.
8. Release the Test Button.
9. The LED status indicator will return to default state (green).
1.3 END-toEND Test
NOTE: If you are NOT using the Searchzone Sonik App, begin with Step 4.
1. Login to the Searchzone Sonik App.
2. Connect the Searchzone Sonik App to the detector.
3. Navigate to main menu and tap on Detector Overview. Then tap on
Proof Test.
4. Aim the Hand Held Test Tool to the face of the detector. Keep distance
in the range of 1 to 10 m (3.3 to 33 ft.).
5. Turn and hold the Rotating Collar (Figure
) to select Test Mode
2. Holding the collar in this position, press and hold the Test Button
(Figure ).
6. The detector will recognize the test signal and the visible status
indicator will flash red. The alarm relays will change state and the 420mA
loop will rise to indicate an Alarm condition.

7
7. While the Rotating Collar is rotated and Test Button pressed the
Searchzone Sonik App will indicate the test signal as recognized. The LED
status indicator will flash red.
8. Release the Test Button and the Rotating Collar on the Hand Held Test
Tool.
9. Detector LED status indicator, relays and 420mA loop will return to
default state.
1.4 Battery replacement
WARNING
Do not mix battery types. Replace the batteries only with the types
listed in Specifications. Use of batteries other than those listed in
Specifications will invalidate the certification.
1. Use a hexagon socket key size 6 mm and rotate it counter-clockwise to
loosen the end cap (Figure ).
2. Slide the battery pack out of the Hand Held Test Tool (Figure ).
3. Replace batteries in the pack. Refer to the Specifications for acceptable
battery types. Position the negative battery terminals against the springs
(Figure ).
4. Slide the battery pack into the Hand Held Test Tool.
5. Gently rotate the battery pack clockwise/anticlockwise until it locates
in the guide grooves and slide it fully into position. Incorrect position of
the battery pack will not allow the end cap to be mounted back (Figure ).
6. Replace the end cap and rotate clockwise. Use a hexagon socket key
size 6 mm and tighten gently (Figure ).

8
1.5 Specifications
Environmental 20°C to +50°C (4°F to +122°F); 0 % to 100 % RH condensing
Output Signals Test Signal 1 - 40 kHz , min. 96 dB SPL at 1 m
Test Signal 2 - 40 kHz , min. 96 dB SPL at 1 m
Signal Range max. 10 m
Storage
Temperature Range
+5°C to +30°C (+41°F to +86°F)
Internal Battery Cell AAA type, primary cells, following types allowed only:
• Duracell ID2400 Industrial AAA cell
• Duracell PC2400 Procell AAA cell
• Duracell MN2400 Deluxe AAA cell
• Duracell QU2400 Quantum AAA cell
• Duracell MX2400 Ultrapower AAA cell
• Duracell MN2400 Pluspower AAA cell
Battery Life min. 100 tests per year for 5 years, starting with a new set of AAA primary
cells
Weight 668 g (1.47 lbs)
Dimensions 100 mm x 150 x 50 mm
Ingress Protection IP 66
Compliance to
Standards
EMC Directive
RoHS
China RoHS
Safety Approvals ATEX / IECEx – DEMKO20ATEX2247 / IECExUL20.0043
II 2 G
Ex ia IIC T4 Gb
Ta 20 °C to + 50 °C
cULus – E 465385
Cl I, Div 1 Grps A, B, C, D T4
Class I Zn. 1 AEx ia IIC T4
Ex ia IIC T4
Ta 20 °C to + 50 °C

07/20
2331M1305 Issue 1 ECO A05425
© 2020 Honeywell Analytics
Please Note:
While every effort has been made to ensure
accuracy in this publication, no responsibility
can be accepted for errors or omissions. Data
may change, as well as legislation and you are
strongly advised to obtain copies of the most
recently issued regulations, standards and
guidelines. This publication is not intended to
form the basis of a contract.
Find out more
www.honeywellanalytics.com
Contact Honeywell Analytics:
Europe, Middle East, Africa, India
Life Safety Distribution GmbH
Javastrasse 2
8604 Hegnau
Switzerland
Tel: [phone]
Fax: [phone]
India Tel: [phone]
[e-mail]
Americas
Honeywell Analytics Inc.
405 Barclay Blvd.
Lincolnshire, IL 60069
USA
Tel: [phone]
Toll free: [phone]
Fax: [phone]
[e-mail]
Asia Pacific
Honeywell Analytics Asia Pacific
7F SangAm IT Tower
434 Worldcup Buk-ro,
Mapo-gu, Seoul 03922
Korea
Tel: +82269090300
Fax: +82269090328
[e-mail]
Technical Services
EMEA: [e-mail]
US: [e-mail]