Honeywell GKP User manual

Installer Programming mode User Programming mode Master User Programming
mode
GKP advanced functionalities
Version V1.0
Author: Florent Busnoult, EMEA Residential Sales Support EMEA, HSF
Date: 15/11/2016

© 2015 by Honeywell International Inc. All rights reserved.
9
Recap’
1
Installer
Procedure Sucrebox Domonial
Step by step guide
Set
arming with
identification
  Here
Set quick
arming   Here
Associate a TAG to a
user
  Here
Change a user’s code
  Here
Disable a user’s code
  Here
Disable a user
  Here
Enable a user
  Here

© 2015 by Honeywell International Inc. All rights reserved.
9
Recap’
1
Master User
Adjust beep volume
  Here
Enable Chime
  Here
Disable Chime
  Here
Assign TAG
Here
Changing
Code
  Here
Disabling
Code
  Here
Enable user
  Here
Disable user
  Here
User
Procedure Sucrebox Domonial
Step by step guide

© 2015 by Honeywell International Inc. All rights reserved.
9
Set arming with identification
1
3 -Press “Total arming” button to select function
4 -Press to activate arming with identification (code and TAG)
Installer Programming mode
Enter the installer programming mode
1 -Press simultaneously the two buttons “1” and “3” more than 2
seconds and release them.
A double beep is played and all Status LEDs light up.
2 -Enter installer’s code. On sucrebox: 001234
All Status LEDs start flashing and a long beep is played
5 -Press (⑤to exit programming and save your changes
All LEDs stop flashing and a double beep is played

© 2015 by Honeywell International Inc. All rights reserved.
9
Set quick arming (no identification needed)
1
3 -Press “Total arming” button to select function
4 -Press to activate quick arming
Installer Programming mode
Enter the installer programming mode
1 -Press simultaneously the two buttons “1” and “3” more than 2
seconds and release them.
A double beep is played and all Status LEDs light up.
2 -Enter installer’s code. On sucrebox: 001234
All Status LEDs start flashing and a long beep is played
5 -Press (⑤to exit programming and save your changes
All LEDs stop flashing and a double beep is played

© 2015 by Honeywell International Inc. All rights reserved.
9
Associate a TAG to a user
1
3 -Press “0 to 9” button to select user’s number
4 -Present the TAG to the tag reader
Installer Programming mode
Enter the installer programming mode
1 -Press simultaneously the two buttons “1” and “3” more than 2
seconds and release them.
A double beep is played and all Status LEDs light up.
2 -Enter installer’s code. On sucrebox: 001234
All Status LEDs start flashing and a long beep is played
5 -Press (⑤to exit programming and save your changes
All LEDs stop flashing and a double beep is played

© 2015 by Honeywell International Inc. All rights reserved.
9
Change a user’s code
1
3 -Press “0 to 9” button to select user’s number
4 -Enter new user’s code (4 or 6 digits)
5 -Re-enter new user’s code
Installer Programming mode
Enter the installer programming mode
1 -Press simultaneously the two buttons “1” and “3” more than 2
seconds and release them.
A double beep is played and all Status LEDs light up.
2 -Enter installer’s code. On sucrebox: 001234
All Status LEDs start flashing and a long beep is played
6 -Press (⑤to exit programming and save your changes
All LEDs stop flashing and a double beep is played

© 2015 by Honeywell International Inc. All rights reserved.
9Disable a user’s code (disable the code for a user and keep the
TAG only)
1
3 -Press “0 to 9” button to select user’s number
4 -Enter 0000 (or 000000 if 6 digits)
5 -Press
Installer Programming mode
Enter the installer programming mode
1 -Press simultaneously the two buttons “1” and “3” more than 2
seconds and release them.
A double beep is played and all Status LEDs light up.
2 -Enter installer’s code. On sucrebox: 001234
All Status LEDs start flashing and a long beep is played
6 -Press (⑤to exit programming and save your changes
All LEDs stop flashing and a double beep is played

© 2015 by Honeywell International Inc. All rights reserved.
9
Disable a user
1
3 -Press “0 to 9” button to select user’s number
4 -Press to disable the user (code and TAG)
Installer Programming mode
Enter the installer programming mode
1 -Press simultaneously the two buttons “1” and “3” more than 2
seconds and release them.
A double beep is played and all Status LEDs light up.
2 -Enter installer’s code. On sucrebox: 001234
All Status LEDs start flashing and a long beep is played
5 -Press (⑤to exit programming and save your changes
All LEDs stop flashing and a double beep is played

© 2015 by Honeywell International Inc. All rights reserved.
9
Enable a user
1
3 -Press “0 to 9” button to select user’s number
4 -Press to enable the user (code and TAG)
Installer Programming mode
Enter the installer programming mode
1 -Press simultaneously the two buttons “1” and “3” more than 2
seconds and release them.
A double beep is played and all Status LEDs light up.
2 -Enter installer’s code. On sucrebox: 001234
All Status LEDs start flashing and a long beep is played
5 -Press (⑤to exit programming and save your changes
All LEDs stop flashing and a double beep is played