Honeywell 5005 User manual

Model 5005/5005B/5005P/5005W
STEEL SECURITY SAFE
Read this manual carefully and never store it inside the safe!
http://www.monomachines.com/
http://www.monomachines.com/
For More Info
Click Here --->

Model 5005/5005B/5005P/5005W
Steel Security Safe with Digital Lock
PACKAGE CONTENTS
1 – Steel Security Safe
1 – Operation Manual
2 – Override Access Keys
4 – “AA” Batteries
1 – Mounting Kit w/ Bolts
ATTENTION
DO NOT RETURN SAFE TO STORE!
For missing parts or difficulty operating your safe, please contact our Consumer
Assistance Department by telephone.
Store will not accept returned products without prior authorization. You must first
contact our consumer assistance department.
PRODUCT OVERVIEW
A - Entry Knob
B - Override Key Cover
C - Electronic Digital Keypad
D - Cabinet Body
E - Door Assembly
F - Serial Number Label
1
http://www.monomachines.com/
http://www.monomachines.com/
For More Info
Click Here --->

SETUP
STEP 1. OPEN SAFE WITH OVERRIDE KEY
1. Remove override key cover with small screwdriver.
2. Insert override key and turn left to unlock safe.
3. Turn knob to right and open safe door.
STEP 2. INSTALL BATTERIES
1. Remove battery compartment (A) cover on inside
door. Insert 4 “AA” batteries (included). Ensure the
batteries are installed in the correct direction, with
regard to polarity (+ and -) See diagram.
2. Replace the battery cover.
3. Do not close door before testing digital lock.
STEP 3. TEST DIGITAL LOCK
1. With door open, turn knob left to put locking door bolts in lock position.
2. Remove override key and store in a secure place.
NEVER STORE KEYS INSIDE SAFE!
3. Enter the preset pass code: “1”-“5”–“9”-“E”.
4. Turn knob to right within 5 seconds.
5. Lock bolts should recede into the unlocked position.
STEP 4. PROGRAM A NEW PASSCODE
1. With door open, press reset button (C) inside
door.
2. Yellow light is on, enter new pass code in 30
seconds.
3. Enter new code (3 to 8 digits) followed by “E”.
Press “C” to clear entry if wrong digit is entered.
4. Safe will beep and yellow light will turn off.
NOTE: The factory pre-set code will not work after a new pass code is programmed.
OPERATION
TO OPEN THE SAFE
1. To unlock and open safe, enter the pass code followed by “E”.
2. Green light will turn on.
3. You will have 5 seconds to turn door entry knob to the right and
open door.
TO CLOSE THE SAFE
1. Close the door and hold it in the closed position.
2. Turn door entry knob to left to engage the lock bolts and lock safe.
2
http://www.monomachines.com/
http://www.monomachines.com/
For More Info
Click Here --->

SECURE LOCKOUT PERIODS
If a wrong code is entered three times in a row, the digital keypad will begin a five-
minute secure lockout period. During this secure lockout period the keypad will
become disabled. Once the lockout period has expired, the safe can be unlocked
using the correct passcode. You may use the override key to open safe, but keypad
will complete the full lockout period.
OVERRIDE ACCESS KEY
If the pass code is unavailable or your keypad fails due to dead batteries or other
malfunction, you can open the safe using the override access key (see STEP 1. in the
SETUP section).
REPLACING BATTERIES
Note: The pass code will not be erased if the batteries become weak or are removed.
Weak or dead batteries should be replaced immediately and all 4 batteries should be
changed. To replace the batteries please follow the instructions in STEP 2. in the
“SETUP” section. Remember to always remove batteries from safe if not using for an
extended period of time. If your batteries are completely dead and you cannot open
the safe by using the digital keypad, use the override access key to open safe and
access the battery compartment.
NOTE: It is NOT RECOMMENDED to use Non-alkaline or rechargeable batteries.
IF YOU FORGET THE PASSCODE
1. Use the override access key to open safe.
2. With door open, press red reset button (C) inside
door.
3. Yellow light is on; enter new pass code in 30
seconds.
4. Enter pass code (3 to 8 digits) followed by “C”
5. Safe will beep and yellow light will turn off.
3
http://www.monomachines.com/
http://www.monomachines.com/
For More Info
Click Here --->

ORDERING NEW / REPLACEMENT KEYS
The following information is required to order keys:
1. PROOF OF OWNERSHIP (1 of 2 Options Below)
SALES RECEIPT & IDENTIFICATION – INTERNATIONAL ORDERS
ONLY!
•Copy of sales receipt showing Store, Date & Product
Description.
•Copy of your picture I.D. (Drivers license, passport, regular I.D.).
PRODUCT OWNERSHIP VERIFICATION FORM
If sales receipt is not available, contact us by email or telephone to
request a “Product Ownership Verification Form”.
2. ORDER INFORMATION
CONTACT INFORMATION
•Name & Shipping Address
•E-mail address (If Available)
•Telephone Number
•Best Time to Contact You
PRODUCT INFORMATION
•Safe Model #
•Safe Serial #
•Lock Key #
•Quantity of Keys Ordered
3. METHOD OF PAYMENT
•Telephone:
Visa or MasterCard
•Mail:
Check or Money Order
NOTE: For pricing please contact Consumer Assistance.
Contact information is located on the back cover of this manual
Terms subject to change without prior notification.
LOCATING SAFE IDENTIFICATION NUMBERS
SERIAL NUMBER
Located on lower right corner on front of
safe. Do Not Remove Safe I.D. Tags!
4
http://www.monomachines.com/
http://www.monomachines.com/
For More Info
Click Here --->

MOUNTING KIT
You may bolt your safe to the wall or floor to added theft protection and
resistance to tipping. Your safe has pre-drilled bolt-down holes in the back
panel and in the floor.
To secure your safe to the wall and/or floor:
1. Select a suitable and convenient location for your safe.
2. Empty the safe and remove the carpet.
3. Locate the predrilled holes on the inside of safe.
4. Place your safe in the desired location.
5. Line up the predrilled holes and mark the floor or wall through the holes.
NOTE: It is not recommended to attempt to bolt to both floor and wall.
6. Move the safe aside to clear marked spots for drilling.
7. Drill holes appropriate for hardware being used and the mounting surface.
INCLUDED: (2 each – bolts, washers and masonry anchors).
8. Place the safe back over the holes and install the fasteners as required.
9. Once completed, replace the carpet.
NOTE: Bolting/unbolting of the unit is at the consumer’s expense and
discretion. LH Licensed Products is not responsible for any costs incurred if
the unit is to be replaced.
If you have any questions about mounting the safe, please check with your
local home center/hardware retailer or independent contractor.
5
http://www.monomachines.com/
http://www.monomachines.com/
For More Info
Click Here --->

LIMITED WARRANTY
LH Licensed Products, Inc., (“LHLP, Inc.”) warrants that for a period of seven (7) years
from the date of purchase, this product will be free from structural or mechanical
defects resulting from materials or workmanship. LHLP, Inc., at its sole option and as
the purchaser’s sole remedy under this warranty, will repair or replace this product or
any component of the product found to be defective during the warranty period.
Replacement or repair will be made with a new or remanufactured product or
component. If the product is no longer available, replacement may be made with a
similar product of equal or greater value.
THIS IS YOUR EXCLUSIVE WARRANTY.
Our goods come with guarantees that cannot be excluded under the Australian
Consumer Law. You are entitled to a replacement or refund for a major failure and for
compensation for any other reasonably foreseeable loss or damage. You are also
entitled to have the goods repaired or replaced if the goods fail to be of acceptable
quality and the failure does not amount to a major failure.
This warranty is only valid for the original retail purchaser from the date of initial retail
purchase and is not transferable. You must keep the original sales receipt. Proof of
purchase is required to obtain warranty service.
LHLP, Inc. dealers, service centers, or retail stores selling this product do not have the
right to alter, modify or in any way change the terms and conditions of this warranty.
This warranty does not apply to the finish on the product. This warranty does not cover
normal wear and tear of parts or damage resulting from any of the following: negligent
use or misuse of the product, use contrary to the operating instructions, disassembly,
repair or alteration by anyone other than LHLP, Inc. or an authorized service center,
improper installation, or exposure to extremes of heat or humidity. Further, the
warranty does not cover Acts of God, such as fire, flood, hurricanes and tornadoes.
LHLP, Inc. shall not be liable for any incidental or consequential damages caused by
the breach of any express or implied warranty or otherwise relating to the sale of this
product. LHLP, Inc. is also not responsible for: costs associated with removing or
installing the product; damage or loss of the contents of the product; nor for the
unauthorized removal of the contents; or damages incurred during shipment.
THE ABOVE WARRANTY IS IN LIEU OF ALL OTHER WARRANTIES, EXPRESS OR
IMPLIED, INCLUDING ANY WARRANTIES OF MERCHANTABILITY OR FITNESS FOR
A PARTICULAR PURPOSE, AND LHLP, INC. DISCLAIMS ANY AND ALL OTHER
COVENANTS AND WARRANTIES.
Except to the extent prohibited by applicable law, any implied warranty of
merchantability or fitness for a particular purpose is limited in duration to the duration
of the above warranty period. Some states, provinces or jurisdictions do not allow the
exclusion or limitation of incidental or consequential damages or limitations on how
long an implied warranty lasts, so the above limitations or exclusion may not apply to
you. This warranty gives you specific legal rights, and you may also have other rights
that vary from state to state, or province to province, or jurisdiction to jurisdiction.
6
http://www.monomachines.com/
http://www.monomachines.com/
For More Info
Click Here --->

The Honeywell Trademark is used under license from
Honeywell International Inc. Honeywell International Inc.
makes no representations or warranties with respect to
this product.
7
http://www.monomachines.com/
http://www.monomachines.com/
For More Info
Click Here --->