Horizon Fitness Endurance 4 User manual

ELLIPTICAL OWNER’S MANUAL
Read the ELLIPTICAL GUIDE before using this OWNER’S MANUAL.
ENDURANCE 4 ENDURANCE 5

2

3
ASSEMBLY
There are several areas during the assembly process that special attention must be paid. It is very important to follow the assembly
instructions correctly and to make sure all parts are firmly tightened. If the assembly instructions are not followed correctly, the
elliptical could have frame parts that are not tightened and will seem loose and may cause irritating noises. To prevent damage to
the elliptical, the assembly instructions must be reviewed and corrective actions should be taken.
Before proceeding, find your elliptical’s serial number located on a white barcode sticker
on the front stabilizer tube and enter it in the space provided below.
ENTER YOUR SERIAL NUMBER AND MODEL NAME IN THE BOXES BELOW:
» Refer to the SERIAL NUMBER and MODEL NAME when calling for service.
WARNING
SERIAL NUMBER:
EP
MODEL NAME: HORIZON ELLIPTICAL
SERIAL NUMBER LOCATION

4
ENDURANCE 4
SHOWN
PIVOTING FOOT PADS
CRANK
TOP CAP
GUIDE RAIL SET
SPEAKERS
WATER BOTTLE HOLDER
UPPER HANDLEBAR
PULSE GRIPS
CONSOLE FAN
STABILIZER TUBE
POWER CORD SOCKET
MAIN FRAME
PEDAL ARM
REAR COVER
IPOD/MP3 PLAYER POCKET
CONSOLE
CONSOLE MAST
TOUCH PAD PANEL
AND DISPLAY WINDOWS
LOWER HANDLEBAR
MANUAL INCLINE LIFT LEVER
LOWER LINK ARM

5
ENDURANCE 5
SHOWN
PIVOTING FOOT PADS
CRANK
TOP CAP
GUIDE RAIL SET
SPEAKERS
WATER BOTTLE HOLDER
UPPER HANDLEBAR
PULSE GRIPS
CONSOLE FAN
STABILIZER TUBE
POWER CORD SOCKET
MAIN FRAME
PEDAL ARM
REAR COVER
IPOD/MP3 PLAYER POCKET
CONSOLE
CONSOLE MAST
TOUCH PAD PANEL
AND DISPLAY WINDOWS
LOWER HANDLEBAR
LOWER LINK ARM

6
TOOLS INCLUDED:
F8 mm L-Wrench
F5 mm L-Wrench / Screwdriver
F13/15 mm Flat Wrench
PARTS INCLUDED:
F1 Stabilizer Tube
F1 Guide Rail Set
F2 Pedal Arms
F1 Manual Incline Set (Endurance 4 only)
F2 Lower Handlebars
F2 Upper Handlebars
F2 Handlebar Caps
F2 Lower Link Arms With Footpads
F1 Top Cap (2 pieces)
F1 Console Mast
F1 Console Mast Boot
F1 Console
F2 Handlebar Caps
F1 Water Bottle Holder
F1 Rear Cover
F1 Audio Adapter Cable
F1 Power Cord
F1 Hardware Kit
UNPACKING
Unpack the product where you will be using it. Place the elliptical carton on a level
flat surface. It is recommended that you place a protective covering on your floor.
Never open box when it is on its side.
NOTE: During each assembly step, ensure that ALL nuts and bolts are in place
and partially threaded in before completely tightening any ONE bolt.
NOTE: A light application of grease may aid in the installation of hardware. Any
grease, such as lithium bike grease is recommended.
NOTE: It is recommended that two people work together for ease and efficiency
while assembling an elliptical.
If you have questions or if
there are any missing parts,
contact Customer Tech
Support. Contact information
is located on the back panel
of this manual.
NEED HELP?
PRE ASSEMBLY
ALL
MODELS

7
BOLTS (A)
SPRING WASHERS (B)
ARC WASHERS (C)
STABILIZER TUBE
MAIN FRAME
BOLTS (A)
SPRING WASHERS (B)
ARC WASHERS (C)
STABILIZER TUBE
MAIN FRAME
ALL
MODELS
ASSEMBLY STEP 1
A Open hardware for step 1.
B Attach the stabilizer tube to the main
frame using 2 bolts (a), 2 spring
washers (b) and 2 arc washers (c) on
each side.
BOLT (A)
30 mm
Qty: 4
SPRING WASHER (B)
15 mm
Qty: 4
ARC WASHER (C)
17 mm
Qty: 4
HARDWARE FOR STEP 1:
ENDURANCE 4 SHOWN
ENDURANCE 5 SHOWN

8
GUIDE RAIL SET
FLAT WASHERS (E)
SPRING WASHERS (F)
NUTS (G)
BOLTS (D)
MANUAL INCLINE
LIFT LEVER SPRING WASHER (F)
15 mm
Qty: 4
FLAT WASHER (E)
16 mm
Qty: 4
BOLT (D)
35 mm
Qty: 4
NUT (G)
Qty: 4
SPRING WASHER (I)
18 mm
Qty: 4
FLAT WASHER (H)
20 mm
Qty: 4
BOLT (J)
25 mm
Qty: 4
ENDURANCE 4 ASSEMBLY STEP 2
* This step is for ENDURANCE 4 only.
A Open hardware for step 2.
B Attach manual incline lift lever to guide
rail set using 4 bolts (d), 4 flat washers
(e), 4 spring washers (f) and 4 nuts (g).
C Align guide rail set with main frame as
shown.
D Lift up on the manual incline lift lever
and place it in one of the holes inside the main
frame.
E Attach the guide rail set to the main frame
using 4 bolts (J), 4 flat washers (h) and 4
spring washers (i).
HARDWARE FOR STEP 2
FLAT WASHERS (H)
SPRING WASHERS (I)
BOLTS (J)
MAIN FRAME
GUIDE RAIL SET
MANUAL INCLINE
LIFT LEVER
ENDURANCE 4
ONLY
ENDURANCE 4 SHOWN

9
ENDURANCE 5 ASSEMBLY STEP 2
* This step is for ENDURANCE 5 models only.
A Open hardware for step 2.
B Attach the guide rail set to the
main frame using 4 bolts (f), 4
spring washers (e) and 4 flat
washers (d).
C Attach the guide rail set to the
incline bracKet using 4 bolts (g),
4 flat washers (h) and 4 spring
washers (i) and 4 nuts (J).
NOTE: You may need to pull the incline
bracket out of the main frame in order to
connect it to the guide rail set.
SPRING WASHER (E)
15 mm
Qty: 4
FLAT WASHER (D)
16 mm
Qty: 4
BOLT (F)
20 mm
Qty: 4
SPRING WASHER (I)
18 mm
Qty: 4
FLAT WASHER (H)
20 mm
Qty: 4
BOLT (G)
35 mm
Qty: 4
NUT (J)
Qty: 4
HARDWARE FOR STEP 2:
FLAT WASHERS (D)
SPRING WASHERS (E)
BOLTS (F)
FLAT WASHERS (H)
SPRING WASHERS (I)
NUTS (J)
GUIDE RAIL SET
INCLINE BRACKET
MAIN FRAME
BOLTS (G)
ENDURANCE 5 SHOWN
ENDURANCE 5
ONLY

10
BOLT (M)
SPRING WASHER (N)
FLAT WASHER (K)
WAVY WASHER (L)
PEDAL ARM
CRANK
PEDAL ARM WHEEL
GUIDE RAIL
CONSOLE MAST
PRE-INSTALLED BOLTS
AND WASHERS
CONSOLE CABLES
MAIN FRAME
ASSEMBLY STEP 3
A Open hardware for step 3.
B Carefully pull the console cable through
the console mast using the twist tie located
inside the console mast.
C Attach console mast to main frame
using pre-installed bolts and
washers.
D Slide wavy washer (l) over cranK
followed by pedal arm as shown. Rest
pedal arm wheel on guide rail.
E Attach the pedal arm to the cranK using 1
flat washer (K), 1 spring washer (n)
and 1 bolt (m).
F Repeat steps D–E on the opposite side of the
elliptical.
BOLT (M)
20 mm
Qty: 2
SPRING WASHER (N)
15 mm
Qty: 2
WAVY WASHER (L)
22.5 mm
Qty: 2
FLAT WASHER (K)
20 mm
Qty: 2
HARDWARE FOR STEP 3:
NOTE: Be
careful not
to pinch any
wires while
attaching the
console mast.
ALL
MODELS
ENDURANCE 5 SHOWN

11
ALL
MODELS
ASSEMBLY STEP 4
A Open hardware for step 4.
B Slide the lower linK arm into
the pedal arm bracKet.
C Attach the lower linK arm to
the pedal arm bracKet using
1 flat washer (s), 1 spring
washer (r) and 1 bolt (Q).
D Repeat steps B–D on the opposite
side of the elliptical.
SPRING WASHER (P)
15.4 mm
Qty: 2
FLAT WASHER (Q)
20 mm
Qty: 2
BOLT (O)
20 mm
Qty: 2
HARDWARE FOR STEP 4:
ENDURANCE 5 SHOWN
SPRING WASHER (R)
BOLT (Q)
FLAT WASHER (S)
LOWER LINK ARM
PEDAL ARM BRACKET

12
BOLT (V)
SPRING
WASHER (U)
HANDLEBAR
CAP
LOWER HANDLEBAR
FLAT WASHERS (S)
FLAT WASHERS (T)
RUBBER WASHER (T)
CONSOLE MAST
A Open hardware for step 5.
B Slide 1 rubber washer (r) and 1 flat
washer (s) onto the console mast.
C Slide lower handlebar onto console
mast and attach using 1 flat washer (s),
1 FLAT WASHER (T), 1 handlebar cap, 1
flat washer (t), 1 spring washer (u)
and 1 bolt (v).
D Repeat steps B–C on the other side.
BOLT (V)
20 mm
Qty: 2
SPRING
WASHER (U)
15 mm
Qty: 2
FLAT
WASHER (S)
25 mm
Qty: 4
FLAT
WASHER (T)
26 mm
Qty: 4
RUBBER
WASHER (R)
26 mm
Qty: 2
ALL
MODELS
ASSEMBLY STEP 5
ENDURANCE 5 SHOWN HARDWARE BAG 5 CONTENTS :

13
BOLT (Z)
FLAT WASHER (X)
NUT (AA)
LOWER HANDLEBAR
SPRING WASHER (Y)
TEFLON WASHERS (W)
LOWER LINK ARM
ALL
MODELS
ENDURANCE 5 SHOWN
A Open hardware bag 6.
B Align end of lower linK arm with bracket on
bottom of lower handlebar.
C Place teflon washers (w) on both sides
of the lower linK arm. While holding
teflon washers (w) slide lower linK
arm into bottom end of lower handlebar.
D Secure the joint with 1 flat washer (X), 1
spring washer (y),1 bolt (z) and secure
with 1 nut (aa).
E Repeat steps B–D on the opposite side of the
elliptical.
SPRING WASHER (Y)
15 mm
Qty: 2
TEFLON
WASHER (W)
28.4 mm
Qty: 4
FLAT WASHER (X)
17 mm
Qty: 2
NUT (AA)
Qty: 2
BOLT (Z)
70 mm
Qty: 2
HARDWARE BAG 6 CONTENTS :
ASSEMBLY STEP 6

14
WATER
BOTTLE
HOLDER
CONSOLE MAST
CONSOLE MAST BOOT
TOP CAP
SCREW (BB)
SCREWS (CC) REAR CAP
SCREWS (BB)
TOP CAP
REAR
COVER
ALL
MODELS
ASSEMBLY STEP 7
A Open hardware bag 7.
B Slide top cap and top cap rear cover
over console mast and snap into place.
C Insert console mast boot over top cap
and snap into place.
D Slide water bottle holder over
console mast and attach using 3
screws (bb).
E Slide rear cap over rear stabilizer and
attach using 2 screws (cc).
HARDWARE BAG 7 CONTENTS :
SCREW (BB)
12 mm
Qty: 3
SCREW (CC)
15 mm
Qty: 2
ENDURANCE 5 SHOWN
NOTE: Be careful not to pinch any
wires while tightening screws.

15
CONSOLE
PRE-INSTALLED BOLTS
UPPER HANDLEBAR
HANDLEBAR CAP
CONSOLE CABLES
LOWER HANDLEBAR
PRE-INSTALLED
SET SCREWS
CONSOLE MAST
ENDURANCE 5 SHOWN
NOTE: Be careful not to pinch
any wires while attaching the
console or handlebars.
A Attach the console cables to the console.
B Carefully tuck the Console cables into the
console mast before attaching the console.
Attach console to console mast using 4
pre-installed bolts.
C The handlebar to the upper handlebar.
D Slide upper handlebar onto lower
handlebar making sure handlebars are joined
together completely. Secure upper handlebar
to lower handlebar using pre-attached
set screws.
E Repeat step E on other side.
NOTE: There is no hardware bag for this step.
Make sure upper handlebars are as far down as possible.
Handlebars can be damaged If not secured correctly.
ALL
MODELS
ASSEMBLY STEP 8

16
ASSEMBLY COMPLETE!
ENDURANCE 4
SHOWN
endurance 4
Max. User Weight: 136 kg / 300 lbs
Product Weight: 84 kg / 185 lbs
Overall Dimension: 190 x 62 x 168 cm / 75” x 24” x 66”

17
endurance 5
Max. User Weight: 148 kg / 325 lbs
Product Weight: 87 kg / 192 lbs
Overall Dimension: 190 x 62 x 168 cm / 75” x 24” x 66”
ENDURANCE 5
SHOWN

18

19
ELLIPTICAL OPERATION
This section explains how to use your elliptical’s console and programming.
The BASIC OPERATION section in the ELLIPTICAL GUIDE has instructions for the following:
• LOCATION OF THE ELLIPTICAL
• POWER/GROUNDING INSTRUCTIONS
• FOOT POSITIONING
• MOVING THE ELLIPTICAL
• LEVELING THE ELLIPTICAL
• POWER/MANUAL INCLINE OPERATION
• USING THE HEART RATE FUNCTION

20
ENDURANCE 4
SHOWN
LEVEL
STOP
START
PAUSE HOLD TO RESET
FÜR NULLSTELLUNG
GEDRÜCKT HALTEN
LEVEL
FAN
VENTILATOR
WIDERSTAND
WIDERSTAND
ENDURANCE 4
SPEED
INTERVALS
GESCHWINDIGKEITS-
INTERVALL
CARDIO
BURN
AUSDAUER
MUSCLE
TONER STRENGTH
BUILDER
KRÄFTIGUNG
PEAK
DESCENT
GIPFELABSTIEG
NATURE
TRAIL
WANDERN
MOUNTAIN
CLIMB
BERGBESTEIGEN
HR
INTERVALS
HR INTERVALL SPITZENINTERVALL
PEAK
INTERVALS
CHANGE
DISPLAY
ANZEIGENWECHSEL
ENTER
GOAL
CENTER
EINGABE
EnergySaver
INTERVAL WORKOUTS
INTERVALLPROGRAMME WEIGHT LOSS WORKOUTS GEWICHTSREDUZIERUNGSPROGRAMME PERFORMANCE WORKOUTS LEISTUNGSPROGRAMME
CONSTANT
WATTS
WATTGESTEUERT
HRC
HERZFREQUENZ-
GESTEUERT
ENERGIESPARMODUS Q
I I
C
J
D
E
G
P
J
H
F
B
N
L
O O
K
A
M