Horizon Fitness EX-59-02 User manual

Read the ELLIPTICAL GUIDE before using this OWNER’S MANUAL.
Lire le GUIDE D’UTILISATION DE L’EXERCISEUR ELLIPTIQUE avant de se servir du présent MANUEL DU PROPRIÉTAIRE.
Lea la GUÍA DE LA MÁQUINA ELÍPTICA antes de usar este MANUAL DEL PROPIETARIO.
ELLIPTICAL OWNER’S MANUAL
MANUEL DU PROPRIÉTAIRE DE L’EXERCISEUR ELLIPTIQUE
MANUAL DEL PROPIETARIO DE LA MÁQUINA ELÍPTICA
EX-59-02
CE4.4

2
2 ENGLISH
30 FRANÇAIS
58 ESPAÑOL

3
IMPORTANT PRECAUTIONS
SAVE THESE INSTRUCTIONS
Read the ELLIPTICAL GUIDE before using this OWNER’S MANUAL. When using an electrical product, basic precautions
should always be followed, including the following: Read all instructions before using this elliptical. It is the responsibility of
the owner to ensure that all users of this elliptical are adequately informed of all warnings and precautions. If you have any
questions after reading this guide, contact Customer Tech Support at the number listed on the back panel.
This elliptical is intended for in-home use only. Do not use this elliptical in any commercial, rental, school or institutional
setting. Failure to comply will void the warranty.

4
TO REDUCE THE RISK OF ELECTRICAL SHOCK:
Always unplug the elliptical from the electrical outlet immediately after using, before cleaning, performing maintenance and putting on or
taking off parts.
DANGER
• To reduce the risk of burns, fire, electrical shock or injury to persons:
• If you experience any kind of pain, including but not limited to chest pains, nausea, dizziness, or shortness of breath, stop
exercising immediately and consult your physician before continuing.
• When exercising, always maintain a comfortable pace. Do not sprint above 80 RPMs on this machine.
• To maintain balance, it is recommended to keep a grip on the handlebars while exercising, mounting or dismounting
the machine.
• Do not turn pedal arms by hand.
• Make sure handlebars are secure before each use.
• Keep the topside of the foot support clean and dry.
• Care should be taken when mounting or dismounting the equipment. Before mounting or dismounting, move the pedal on
the mounting or dismounting side to its lowest position and bring the machine to a complete stop.
• Do not wear clothes that might catch on any part of the elliptical.
• Always wear athletic shoes while using this equipment.
• Do not jump on the elliptical.
• At no time should more than one person be on the elliptical while in operation.
• This elliptical should not be used by persons weighing more than the specified user capacity in the OWNER’S MANUAL
WARRANTY SECTION. Failure to comply will void the warranty.
• This elliptical is intended for in-home use only. Do not use this elliptical in any commercial, rental, school or institutional
setting. Failure to comply will void the warranty.
• Do not use elliptical in any location that is not temperature controlled, such as but not limited to garages, porches, pool
rooms, bathrooms, car ports or outdoors. Failure to comply will void the warranty.
• To prevent electrical shock, never drop or insert any object into any opening.
• Connect this exercise product to a properly grounded outlet only.
WARNING

5
TO REDUCE THE RISK OF BURNS, FIRE, ELECTRICAL SHOCK OR INJURY TO PERSONS:
• Keep power cord away from heated surfaces. Do not carry this unit by its supply cord or use the cord as a handle.
• Do not use other attachments that are not recommended by the manufacturer. Attachments may cause injury.
• Do not operate where aerosol (spray) products are being used or when oxygen is being administered.
• Use the elliptical only as described in the elliptical guide and owner’s manual.
• Disconnect all power before servicing or moving the equipment. To clean, wipe surfaces down with soap and slightly damp
cloth only; never use solvents. (See MAINTENANCE)
• The elliptical should never be left unattended when plugged in. Unplug from outlet when not in use, and before putting on or
taking off parts.
• Do not operate under blanket or pillow. Excessive heating can occur and cause fire, electric shock, or injury to persons.
• At NO time should children under the age of 13 or pets be within 10 feet of the machine.
• At NO time should children under the age of 13 use the elliptical.
• Children over the age of 13 or disabled persons should not use the elliptical without adult supervision.
• Never operate the elliptical if it has a damaged cord or plug, if it is not working properly, if it has been dropped or damaged,
or immersed in water. Contact tech support at the number on the back panel to schedule service.
• To disconnect, turn all controls to the off position, then remove plug from outlet.
• Do not remove the console covers unless instructed by Customer Tech Support. Service should only be done by an
authorized service technician
It is essential that your elliptical is used only indoors, in a climate controlled room. If your elliptical has been exposed
to colder temperatures or high moisture climates, it is strongly recommended that the elliptical is warmed up to room
temperature before first time use. Failure to do so may cause premature electronic failure.
WARNING
WARNING
This product contains chemicals known to the State of California to cause cancer and birth defects or other reproductive harm.

6

7
ASSEMBLY
There are several areas during the assembly process that special attention must be paid. It is very important to follow the
assembly instructions correctly and to make sure all parts are firmly tightened. If the assembly instructions are not followed
correctly, the elliptical could have frame parts that are not tightened and will seem loose and may cause irritating noises. To
prevent damage to the elliptical, the assembly instructions must be reviewed and corrective actions should be taken.
Before proceeding, find your elliptical’s serial number located on a white barcode
sticker on the front stabilizer tube and enter it in the space provided below.
ENTER YOUR SERIAL NUMBER AND MODEL NAME IN THE BOXES BELOW:
» Refer to the SERIAL NUMBER and MODEL NAME when calling for service.
WARNING
SERIAL NUMBER:
EP
MODEL NAME: HORIZON   ELLIPTICAL
SERIAL NUMBER LOCATION

8
UPPER HANDLEBAR
SPEAKERS
PULSE GRIPS
WATER BOTTLE HOLDER
PEDAL ARM
LOWER HANDLEBAR
LOWER LINK ARM
PIVOTING FOOT PADS
REAR STABILIZER
READING RACK
CONSOLE
CONSOLE MAST
TOP CAP
MAIN FRAME
CRANK
POWER CORD SOCKET
STABILIZER TUBE
GUIDE RAIL SET

9
TOOLS REQUIRED:
F8 mm L-Wrench
F13/17 mm Flat Wrench
F5 mm L-Wrench/Screwdriver
FScrewdriver (not included)
PARTS INCLUDED:
F1 Main Frame
F1 Stabilizer Tube
F1 Guide Rail Set
F1 Console Mast
F2 Pedal Arms
F2 Lower Handlebars
F2 Upper Handlebars
F2 Handlebar Cover Sets
F2 Lower Link Arms With Footpads
F1 Front Top Cap Piece
F1 Rear Top Cap Piece
F1 Console
F1 Audio Adapter Cable
F1 Power Cord
F1 Hardware Kit
UNPACKING
Unpack the product where you will be using it. Place the elliptical carton on a
level flat surface. It is recommended that you place a protective covering on
your floor. Never open box when it is on its side.
If you have questions or if there are any missing parts, contact Customer
Tech Support. Contact information is located on the back panel of this
manual.
NEED HELP?
PRE ASSEMBLY
• It is recommended that two people work together for ease and efficiency
while assembling an elliptical.
• During each assembly step, ensure that ALL nuts and bolts are in
place and partially threaded. It is recommended you complete the full
assembly of your unit before completely tightening any ONE bolt.
• Several parts have been pre-lubricated to aid in assembly and usage.
Please do not wipe this off. If you have difficulty, a light application of
lithium bike grease is recommended.
IMPORTANT NOTES

10
ASSEMBLY STEP 1
A Open HARDWARE FOR STEP 1.
B Attach the STABILIZER TUBE (1) to the
MAIN FRAME (2) using 2 BOLTS (A),
2 SPRING WASHERS (B) and 2 ARC
WASHERS (C) on each side.
A
B
C
2
1
HARDWARE FOR STEP 1
PART TYPE DESCRIPTION QTY
A BUTTON HEAD BOLT M8X1.25PX30L 4
BSPRING WASHER 8.2X15.4X2.0T 4
CARC WASHER 8.4X17.0X1.0T 4

11
HARDWARE FOR STEP 2
PART TYPE DESCRIPTION QTY
D SOCKET CAP BOLT M10X1.5PX20L 4
ESPRING WASHER 10.2X18.4X2.5T 4
FFLAT WASHER 10.2X20.0X1.5T 4
ASSEMBLY STEP 2
3
2
E
F
D
A Open HARDWARE FOR STEP 2.
B Align GUIDE RAIL SET (3) with MAIN
FRAME (2) as shown.
C Attach the GUIDE RAIL SET (3) to the
MAIN FRAME (2) using 4 BOLTS (D),
4 SPRING WASHERS (E) and 4 FLAT
WASHERS (F).

12
2
6
4
8
I
J
B
7
5
H
G
NOTE: Be
careful not
to pinch any
wires while
attaching the
console mast.
ASSEMBLY STEP 3
A Open HARDWARE FOR STEP 3.
B Remove PRE-INSTALLED BOLTS AND
WASHERS (6) from MAIN FRAME (2).
C Carefully pull the CONSOLE CABLE (4) through
the CONSOLE MAST (5) using the twist tie
located inside the CONSOLE MAST (5).
D Attach CONSOLE MAST (5) to MAIN FRAME (2)
using PRE-INSTALLED BOLTS AND WASHERS
(6).
E Slide WAVY WASHER (G) and FLAT WASHER
(H) over CRANK (7) followed by PEDAL ARM (8)
as shown. Rest pedal arm wheel on guide rail.
F Attach the PEDAL ARM (8) to the CRANK (7)
using 1 FLAT WASHER (I), 1 SPRING WASHER
(B) and 1 BOLT (J).
G Repeat steps E–F on the opposite side of the
elliptical.
HARDWARE FOR STEP 3
PART TYPE DESCRIPTION QTY
GWAVY WASHER 17.2X22.5X0.5T 2
HFLAT WASHER 16.0X25.0X1.0T 2
IFLAT WASHER 8.2X30.0X1.5T 2
BSPRING WASHER 8.2X15.4X2.0T 2
J BUTTON HEAD BOLT M8X1.25PX15L 2

13
HARDWARE FOR STEP 4
PART TYPE DESCRIPTION QTY
KFLAT WASHER 20.2X27.2X1.5T 4
LWAVY WASHER 20.7X29.1X0.5T 2
IFLAT WASHER 8.2X20.0X1.5T 2
BSPRING WASHER 8.2X15.4X2.0T 2
J BUTTON HEAD BOLT M8X1.25PX20L 2
ASSEMBLY STEP 4
9
10
K
L
K
I
B
J
A Open HARDWARE FOR STEP 4.
B Slide 1 FLAT WASHER (K), 1 WAVY
WASHER (L) and another FLAT
WASHER (K) onto the LOWER LINK ARM
(9).
C Slide the LOWER LINK ARM (9) into the
PEDAL ARM BRACKET (10).
D Attach the LOWER LINK ARM (9)
to the PEDAL ARM BRACKET (10)
using 1 FLAT WASHER (I), 1 SPRING
WASHER (B) and 1 BOLT (J).
E Repeat steps B–D on the opposite side of
the elliptical.

14
H
G
H
I
B
5
12
J
ASSEMBLY STEP 5
A Open HARDWARE FOR STEP 6.
B Slide 1 FLAT WASHER (H), 1 WAVY WASHER
(G) and 1 FLAT WASHER (H) onto the
CONSOLE MAST (5).
C Slide LOWER HANDLEBAR (12) onto
CONSOLE MAST (5) and attach using 1 FLAT
WASHER (I), 1 SPRING WASHER (B) and 1
BOLT (J).
D Repeat steps B–C on the other side.
HARDWARE FOR STEP 5
PART TYPE DESCRIPTION QTY
GWAVY WASHER 17.2X22.5X0.5T 2
HFLAT WASHER 16.0X25.0X1.0T 4
IFLAT WASHER 8.2X30.0X1.5T 2
BSPRING WASHER 8.2X15.4X2.0T 2
J BUTTON HEAD BOLT M8X1.25PX20L 2

15
HARDWARE FOR STEP 6
PART TYPE DESCRIPTION QTY
KBOLT M8X1.25PX70L-12L 2
BSPRING WASHER 8.2X15.4X2.0T 2
IFLAT WASHER 8.2X20.0X1.5T 2
LNUT M8X1.25P 2
ASSEMBLY STEP 6
12
I
B
9
K
L
A Open HARDWARE BAG 6.
B Slide LOWER LINK ARM (9) into bottom end of
LOWER HANDLEBAR (12).
C Secure the joint with 1 BOLT (K), 1 SPRING
WASHER (B),1 FLAT WASHER (I) and 1
NUT (L).
D Repeat steps B–C on the opposite side of
the elliptical.

16
ASSEMBLY STEP 7
13
14
15
12
M
15
A Open HARDWARE BAG 7.
B Slide the right (R) UPPER HANDLEBAR
(13) onto the right LOWER HANDLEBAR
(12) making sure handlebars are joined
together completely. Secure the UPPER
HANDLEBAR (13) to the LOWER
HANDLEBAR (12) using PRE-ATTACHED
SET SCREWS (14).
C Slide right (R) HANDLEBAR COVERS (15)
over UPPER HANDLEBARS (13) and attach
using 1 SCREW (M).
D Repeat STEPS B–C on left side.
HARDWARE FOR STEP 7
PART TYPE DESCRIPTION QTY
MSCREW M4X0.7PX8L 4
NOTE: Make sure upper handlebars are as far
down as possible. Handlebars can be damaged
If not secured correctly.

17
4
16
19
5
17
18
ASSEMBLY STEP 8
ASSEMBLY COMPLETE!
NOTE: All hardware for this step is pre-installed.
A Remove 4 PRE-INSTALLED BOLTS (16) from
the CONSOLE (17).
B Attach the CONSOLE CABLES (4) to the
CONSOLE (17).
C Carefully tuck the CONSOLE CABLES (4)
into the CONSOLE MAST (5) before attaching
the CONSOLE. Attach CONSOLE (17) to
CONSOLE MAST (5) using 4 PRE-INSTALLED
BOLTS (16).
D Slide FRONT TOP CAP PIECE (18) and REAR
TOP CAP PIECE (19) over CONSOLE MAST
(5) and snap into place.
NOTE:
Do not to pinch any wires while attaching the console.

18

19
ELLIPTICAL OPERATION
This section explains how to use your elliptical’s console and programming.
The BASIC OPERATION section in the ELLIPTICAL GUIDE has instructions for the following:
• LOCATION OF THE ELLIPTICAL
• POWER/GROUNDING INSTRUCTIONS
• FOOT POSITIONING
• MOVING THE ELLIPTICAL
• LEVELING THE ELLIPTICAL
• POWER/MANUAL INCLINE OPERATION
• USING THE HEART RATE FUNCTION

20
3412 5678910
resistance resistance
speedheart rate
calorieswattsdistancetime RPM
start
pause
stop
hold to reset
change
display
C
A
L
M
I I
E
J K
D
FG
B
H