Horizon Fitness ANDES E User manual

ELLIPTICAL OWNER’S MANUAL
Read the ELLIPTICAL GUIDE before using this OWNER’S MANUAL.

32
ASSEMBLY
There are several areas during the assembly process that special attention must be paid. It is very important to follow the
assembly instructions correctly and to make sure all parts are firmly tightened. If the assembly instructions are not followed
correctly, the elliptical could have frame parts that are not tightened and will seem loose and may cause irritating noises.
To prevent damage to the elliptical, the assembly instructions must be reviewed and corrective actions should be taken.
Before proceeding, find your elliptical’s serial number located on a white barcode
sticker on the front stabilizer tube and enter it in the space provided below.
ENTER YOUR SERIAL NUMBER AND MODEL NAME IN THE BOXES BELOW:
» Refer to the SERIAL NUMBER and MODEL NAME when calling for service.
WARNING
3ENGLISH
SERIAL NUMBER:
EP
SERIAL NUMBER LOCATION
MODEL NAME: HORIZON ELLIPTICAL

54
TOOLS INCLUDED:
F5 mm L-Wrench
F8 mm L-Wrench
F10/13 mm Flat Wrench
FScrewdriver
PARTS INCLUDED:
F1 Main Frame
F1 Guide Rail Set
F2 Pedal Arms
F2 Lower Handlebars
F2 Upper Handlebars
F2 Lower Link Arms With Footpads
F1 Top Cap
F1 Console Mast
F1 Console Mast Boot
F1 Console
F2 Handlebar Caps
F1 Water Bottle Holder
F1 Audio Adapter Cable
F1 Power Cord
F1 Hardware Kit
UNPACKING
Unpack the product where you will be using it. Place the elliptical carton on a level
flat surface. It is recommended that you place a protective covering on your floor.
Never open box when it is on its side.
NOTE: During each assembly step, ensure that ALL nuts and bolts are in place and
partially threaded in before completely tightening any ONE bolt.
NOTE: A light application of grease may aid in the installation of hardware. Any
grease, such as lithium bike grease is recommended.
If you have questions or if there
are any missing parts, contact
Customer Tech Support.
NEED HELP?
PRE ASSEMBLY
SPEAKERS
UPPER HANDLE BAR
TOUCH PAD PANEL AND DISPLAY WINDOWS
PULSE GRIPS
WATER BOTTLE HOLDER
TOP CAP
MAIN FRAME
PIVOTING FOOT PADS
GUIDE RAIL SET
REAR COVER
READING RACK
CONSOLE MAST
LOWER HANDLEBAR
POWER CORD SOCKET
CRANK
LOWER LINK ARM
PEDAL ARM
CONSOLE

76
ASSEMBLY STEP 1 ASSEMBLY STEP 2
A
Bolt
M10
Qty: 4
B
Spring washer
Φ10.2
Qty: 4
C
Flat washer
Φ10.2
Qty: 4
HARDWARE BAG 1 CONTENTS:
A Open HARDWARE BAG 1.
B Align GUIDE RAIL SET with MAIN FRAME as
shown.
C Attach the GUIDE RAIL SET to the MAIN
FRAME using 4 BOLTS (A), 4 SPRING
WASHERS (B) and4 FLAT WASHERS (C).
A
B
C
GUIDE RAIL SET
MAIN FRAME
NOTE: Be careful
not to pinch
any wires while
attaching the
console mast.
A Open HARDWARE BAG 2.
B Carefully pull the CONSOLE CABLE through
the CONSOLE MAST using the twist tie
located inside the CONSOLE MAST.
C Attach CONSOLE MAST to MAIN FRAME
using PRE-INSTALLED BOLTS AND
WASHERS.
D Slide WAVE WASHER (G) over CRANK
followed by PEDAL ARM as shown. Rest
PEDAL ARM WHEEL on GUIDE RAIL.
E Attach the PEDAL ARM to the CRANK using
1FLAT WASHER (F), 1 SPRING WASHER
(E) and 1 BOLT (D).
F Repeat steps D–E on the opposite side of the
elliptical.
D
Bolt
M8
Qty: 2
E
Spring washer
Φ8.2
Qty: 2
F
Flat washer
Φ8.2
Qty: 2
G
Wave washer
Φ17.2
Qty: 2
HARDWARE BAG 2 CONTENTS:
D
E
G
F
CRANK
PRE-INSTALLED BOLTS
AND WASHERS
GUIDE RAIL
PEDAL ARM
PEDAL ARM
PEDAL ARM WHEEL
CONSOLE MAST
MAIN FRAME
CONSOLE CABLE

98
ASSEMBLY STEP 3 ASSEMBLY STEP 4
A Open HARDWARE BAG 3.
B Slide 1 FLAT WASHER (K), 1 WAVE
WASHER (L) and another FLAT WASHER (K)
onto the LOWER LINK ARM.
C Slide the LOWER LINK ARM into the PEDAL
ARM BRACKET.
D Attach the LOWER LINK ARM to the PEDAL
ARM BRACKET using 1 FLAT WASHER (J),
1 SPRING WASHER (I) and 1 BOLT (H).
E Repeat steps B–D on the opposite side ofthe
elliptical.
H
Bolt
M8
Qty:2
J
Flat washer
Φ8.2
Qty:2
K
Flat washer
Φ20.2
Qty:4
L
Wave washer
Φ20.7
Qty:2
I
Spring washer
Φ8.2
Qty:2
HARDWARE BAG 3 CONTENTS:
H
K
L
K
I
J
LOWER LINK ARM
PEDAL ARM BRACKET
PEDAL ARM BRACKET
LOWER LINK ARM
A Open HARDWARE BAG 4.
B Slide 1 RUBBER WASHER (Q), 1 FLAT
WASHER (P) onto the CONSOLE MAST.
C Slide LOWER HANDLEBAR onto CONSOLE
MAST and attach using 1 FLAT WASHER (P),
1 FLAT WASHER (O), 1 HANDLEBAR CAP,
1 FLAT WASHER (O), 1 SPRING WASHER
(N) and 1 BOLT (M).
D Repeat steps B–C on the opposite side of the
elliptical.
M
Bolt
M8
Qty:2
O
Flat washer
Φ8.5
Qty:4
P
Flat washer
Φ16.0
Qty:4
Q
Rubber washer
Φ16.2
Qty:2
N
Spring washer
Φ8.2
Qty:2
HARDWARE BAG 4 CONTENTS:
M
N
P
Q
O
O
P
CONSOLE MAST HANDLEBAR CAP
LOWER HANDLEBAR
LOWER HANDLEBAR