Horizon Fitness 5.0IC User manual

INDOOR CYCLE OWNER’S MANUAL

23
3 ENGLISH ASSEMBLY
There are several areas during the assembly process that special attention must be paid. It is very important to follow the
assembly instructions correctly and to make sure all parts are firmly tightened. If the assembly instructions are not followed
correctly, the indoor cycle could have parts that are not tightened and will seem loose and may cause irritating noises. To
prevent damage to the indoor cycle, the assembly instructions must be reviewed and corrective actions should be taken.
Before proceeding, find your indoor cycle’s serial number located on
the front stabilizer of the cycle and enter it in the space provided below.
ENTER YOUR SERIAL NUMBER IN THE BOX BELOW:
» Refer to the SERIAL NUMBER and MODEL NAME when calling for service.
» Be sure to enter both the SERIAL NUMBER and MODEL NAME on your warranty card.
SERIAL NUMBER:
MODEL NAME: HORIZON INDOOR CYCLE
WARNING
36
ENGLISH

4 5
MAIN PARTS INCLUDED:
Main Frame (20)
Front Stabilizer (21F)
Rear Stabilizer (21R)
Handlebar Set (22)
Handlebar Post (23)
Console (29)
Pedal Set (34 L&R)
Seat Post Set (31, 32 & 33)
PARTS PACKING
INCLUDED:
1 Hardware Kit
HARDWARE KIT:
Tablet holder
Console (29)
Handlebar adjustment knob (24)
Emergency brake
Flywheel
Water bottle holder (30)
Transport wheels
Stabilizer (21F)
Pedals (34 L&R)
Stabilizer (21R)
Crank arms (35 L&R)
Seat slider (33)
Seat height knob
Seat adjustment lever (31)
Seat (32)
Handlebar set (22)
Handlebar post (23)
Main frame (20)
MODEL INFORMATION PRE ASSEMBLY
UNPACKING
Due to the weight of the indoor cycle, it is recommended that two people
perform the assembly. Unpack the product where you will be using it. It is
recommended that you place a protective covering on your floor. Place the carton
on a level flat surface and remove all packing materials; do not dispose of the
packing materials until assembly is completed.
NOTE: During each assembly step, ensure that ALL nuts and bolts are in place
and partially threaded in before completely tightening any ONE bolt.
NOTE: A light application of grease may aid in the installation of hardware. Any
grease, such as lithium bike grease is recommended.
NEED HELP?
ENGLISH
ENGLISH
Leveling Feet
1
Bolt
M8
Qty: 7
2
Spring Washer
Ø8.2
Qty: 7
If you have questions or if there are any missing
parts, contact Customer Tech Support.
4
Bolt
M4
Qty: 3
5
Flat Washer
Ø10
Qty: 1
3
Flat Washer
Ø8.2
Qty: 7
Tool Kit
5mm Wrench
13/15mm Wrench
Screwdriver

6 7
ASSEMBLY STEP 1 ASSEMBLY STEP 2
2.1 Open hardware for Step 2.
2.2 Insert Handlebars (22) into Handlebar Post (23)
and secure the front with 1 Bolt (1), 1 Spring
Washer (2) and 1 Flat Washer (3). Do not fully
tighten hardware until end of Step 2.
2.3 Secure the side with 2 Bolt (1), 2 Spring
Washer (2), 2 Flat Washer (3).
2.4 Fully tighten bolts from Steps 2.2 & 2.3.
1.1 Open hardware for Step 1.
1.2 Attach the Front Stabilizer (21F) and Rear
Stabilizer (21R) to the Main Frame (20) using
4 Bolts (1), 4 Spring Washers (2) and 4 Flat
Washers (3), and tighten firmly.
STEP 1 HARDWARE : STEP 2 HARDWARE :
ENGLISH
ENGLISH
1
Bolt
M8
Qty: 4
2
Spring Washer
Ø8.2
Qty: 4
3
Flat Washer
Ø8.2
Qty: 4
23
22
3
2
1
21R
21F
20
1
2
3
1
Bolt
M8
Qty: 3
2
Spring Washer
Ø8.2
Qty: 3
3
Flat Washer
Ø8.2
Qty: 3

8 9
ASSEMBLY STEP 3
3.1 Turn Adjustment Knob (24) counter-clockwise to
fully loosen.
3.2 Attach Lead Wire (26) to Console Cable (25)
and pull Console Cable (25) from Head Tube
(28) through Handlebar Post (23) and out hole
in front of Handlebar Post (23).
3.3 Pull Console Cable (25) through hole in Console
Bracket (27).
3.4 Insert Handlebar Post (23) into Head Tube (28)
and turn Adjustment Knob (24) to secure.
3.5 Detach and discard Lead Wire (26).
NOTE: Be careful not to pinch any wires while
assembling handlebars.
ASSEMBLY STEP 4
4.1 Open hardware for Step 4.
4.2 Attach Console Cable (25) to Console (29).
4.3 Carefully tuck Console Cable (25) into
Handlebar Post (23).
4.4 Route Console Cable (25) through channel on
back of Console (29) to avoid pinching cable.
Attach Console (29) to Console Bracket (27)
using 3 Bolts (4).
STEP 4 HARDWARE :
NOTE: Be careful not to pinch any wires while
assembling console.
ENGLISH
ENGLISH
4
Bolt
M4
Qty: 3
25
25
27
6
29
29
23
STEP 4.2
24
26
23
28
26
23 25
25
27
STEP 3.2 & 3.3

10 11
ASSEMBLY STEP 5
5.1 Open hardware for Step 5.
5.2 Unscrew Adjustment Lever (31) from Seat (31).
5.3 Place Seat (32) onto Seat Slider (33).
5.4 Secure Seat (32) with 1 Flat Washer (5) and
Adjustment Lever (31).
STEP 5 HARDWARE :
ASSEMBLY STEP 6
6.1 Identify Left Pedal (34L) which is labeled Lon
spindle and Right Pedal (34R) labeled R.
6.2 Insert Left Pedal (34L) into Left Crank Arm
(35L) and tighten Counter Clockwise.
6.3 Insert Right Pedal (34R) into Right Crank Arm
(35R) and tighten Clockwise.
6.4 Use Combination Wrench to fully tighten pedals.
CONGRATULATIONS!
You have successfully assembled your indoor cycle.
ENGLISH
ENGLISH
5
Flat Washer
Ø10
Qty: 1
32
31
5
33
34L
35R
34R
35L
STEP 6.1
Product Weight: 38 kg / 85 lbs.
User Weight Capacity: 113 kg / 250 lbs.
Dimensions (L×W×H): 120 x 53 x 115 cm /
47” x 21” x 45”

12 13
INDOOR CYCLE OPERATION
ENGLISH
RESISTANCE CONTROL AND EMERGENCY BRAKE
The preferred level of difficulty in pedaling (resistance) can be regulated in increments by use of the resistance buttons on the
console. To increase the resistance, push the up arrow. To decrease the resistance, push the down arrow.
FOR INDOOR CYCLE:
WARNING
• Make sure your shoes are fixed into the toe cage (if available).
• Apply full resistance load when the Indoor Cycle is not in use
to prevent injuries due to moving drive gear components.
• The Indoor Cycle does not have a free moving flywheel; the
pedals will continue to move together with the flywheel until
the flywheel stops. Reducing speed in a controlled manner is
required. To stop the flywheel immediately, push down hard
the emergency brake. Always pedal in a controlled manner
and adjust your desired cadence according to your own
abilities. Push the emergency brake down = emergency stop.
• The Indoor Cycle uses a fixed flywheel that builds momentum
and will keep the pedals turning even after the user stops
pedaling or if the user’s feet slip off. DO NOT ATTEMPT TO
REMOVE YOUR FEET FROM THE PEDALS OR DISMOUNT
THE MACHINE UNTIL BOTH THE PEDALS AND THE
FLYWHEEL HAVE COMPLETELY STOPPED. Failure to follow
these instructions may lead to loss of control and the potential
for serious injury.
INDOOR CYCLE SEAT & HANDELBAR ADJUSTMENT (IF AVAILABLE)
Rotate the adjustment lever or knob counterclockwise to slide the seat or handlebars forward or backward for horizontal
adjustment; raising or lowering the seat or handlebar with the other hand for height adjustment. Rotate the lever or knob
clockwise to lock the position. Do not adjust seat or handlebar height past MAX mark or adjustment points on post.
ENGLISH
Emergency brake

14 15
CONSOLE DISPLAY
LCD Display:
In the exercise mode, the upper LCD window will always display Cadence and Resistance.
The lower portion of the display can show: Time, Calories (Cal), Heart Rate (HR), Distance (Dist) and Speed. There is also a default
cycle function which will display each of the data types for 5 seconds before cycling to the next.
To lock the lower portion to one specific data display, press the Enter / Display button until the label for the data you
desire is shown. To return to cycling data, press the Enter / Display button until the two arrows are shown.
Up & Down ( / ) Keys:
Press the Up and Down ( / ) keys to increase and decrease the settings: Resistance or Time.
In the exercise mode, the Up and Down arrows will adjust the resistance by 1. If you hold down the arrow keys for more than
1/2 of a second, the resistance range will go up/down by 5 until released.
CONSOLE OPERATION
Manual Setting:
Press Start/Stop button to start a quick manual workout. In this mode, the resistance will start at 0 and the timer will count
up from 0 seconds.
Customize Your Workout:
Press Enter / Display button until Time flashes. Use the Up/Down / keys to adjust your desired workout time and
then press the Enter / Display button to confirm your desired time. Once confirmed, the starting resistance range will
begin flashing. Adjust the desired starting resistance with the Up/Down / keys and confirm with the Enter / Display
button. Press Start to begin the workout with your desired time and resistance.
Once your custom program has been started, the timer will count down from your desired time and the resistance will begin at
the resistance you selected. You may still adjust the resistance to different values during the workout.
Energy Saver:
To minimize energy consumption, your machine will enter energy saver mode (ERP) automatically when not in use and the
console will be woken up quickly with a touch of a button.
CADENCE
TIME
DIST SPEED
CAL
HR
RESISTANCE
HR
MODE
CONSOLE
Up/Down Keys
Bluetooth Button
LCD Display
ENGLISH
ENGLISH

16
HOW TO SWITCH BETWEEN APP MODE & BT HEART RATE MODE
Home- P1
Connecting to HR Strap (off by default)
In order to access to HR Strap mode, make sure the
console is not currently connected to any Bluetooth (BT)
devices by checking that no BT Symbol is displayed on
the console.
Wear the HR strap, make sure to read the strap instruction.
Note: Some chest contact HR straps need to be moist to
read the HR precisely.
Press and hold the Bluetooth button for a few seconds
until “HR MODE” symbol displays on the right LCD corner.
Once the console detects the BT HR strap, the BT symbol
will display on the LED screen.
To exit HR Strap mode, disconnect the BT HR device and
ensure the BT symbol disappears from the display. Then
press and hold Bluetooth button for a few seconds
until “HR MODE” disappears on LED screen. NOTE: it
should take a few seconds for the Bluetooth to disconnect
from the console.
Hit Start to begin a workout and console should show the
heart rate.
Connecting to an App (default mode)
If using a 3rd party App, please turn on your device’s
Bluetooth (BT) and follow the App pairing instructions.
Ensure the bike console is not connected to any other BT
devices by checking that the BT symbol is not lit on the
console.
If you wish to use the BT HR Strap with a 3rd party App
that is capable, then connect to the HR strap from within
the App interface (please follow the App instructions to
find and connect to the HR Strap).
Follow the 3rd party App instructions to start the program.
Some require you to start from inside the App, others
require you to press the console Start button first.
To stop the workout, End Ride in the App and press Stop
button on console for 3 seconds.
ENGLISH

©2022 Johnson Health Tech
Horizon 5.0IC |Rev. 1.0 E