Horizon Fitness Comfort U User manual

COMFORT U
Read the BIKE GUIDE before using this OWNER’S MANUAL.
Lire le GUIDE D’UTILISATION DU VÉLO D’EXERCICE avant de se servir du présent MANUEL DU PROPRIÉTAIRE.
Lea la GUÍA DEL USUARIO DE LA BICICLETA ESTACIONARIA antes de utilizar este MANUAL DEL PROPIETARIO.
EXERCISE BIKE OWNER’S MANUAL
MANUEL DU PROPRIÉTAIRE DU VÉLO D’EXERCICE
MANUAL DEL PROPIETARIO DE LA BICICLETA ESTACIONARIA
COMFORT R

2
2 ENGLISH
40 FRANÇAIS
78 ESPAÑOL

3
IMPORTANT PRECAUTIONS
SAVE THESE INSTRUCTIONS
When using an exercise product, basic precautions should always be followed, including the following: Read all instructions
before using this exercise bike. It is the responsibility of the owner to ensure that all users of this exercise bike are adequately
informed of all warnings and precautions. If you have any questions after reading this owner’s manual, contact Customer
Tech Support at the number listed on the back panel.

4
READ AND SAVE ALL INSTRUCTIONS BEFORE ASSEMBLING OR USING THIS
EXERCISE BIKE. IT IS STRONGLY RECOMMENDED TO TAKE THE FOLLOWING SAFETY
INSTRUCTIONS.
•CAUTION: If you experience chest pains, nausea, dizziness or shortness of breath, stop exercising immediately and consult
your physician before continuing.
•Use this exercise bike for its intended purpose as described in this manual. Do not use attachments that have not been
recommended by the manufacturer.
•Never operate the exercise bike if it is not working properly, or if it has been damaged. Contact Customer Tech Support or
the authorized dealers for examination and repair.
•Do not use the exercise bike without proper footwear. NEVER operate the exercise bike with bare feet.
•Do not wear any clothing that might catch on any moving parts of this exercise bike.
•Keep hands and feet clear at all times from moving parts to avoid injury. Never turn the pedal cranks by hand.
•Do not dismount the exercise bike until the pedals are at a complete STOP.
•Do not attempt to ride the exercise bike in a standing position at high RPMs until you have practiced at slower speeds.
•Do not insert any object, hands or feet into any openings, or expose hands, arms or feet to the drive mechanism or other
potentially moving part of the exercise bike.
•Do not use any equipment that is damaged or has worn or broken parts. Use only replacement parts supplied by Customer
Tech Support or the authorized dealers.
•Do not operate where aerosol (spray) products are being used or when oxygen is being administered.
•Close supervision is necessary when used near children, invalids or disabled people.
•When the exercise bike is in use, young children and pets should be kept at least 3 meters / 10 feet away.
•Ensure that adjustment levers (seat and handlebar fore-and-aft) are properly secured and do not interfere with range of
motion during exercise.
•This product contains chemicals known to the State of California to cause cancer and birth defects or other reproductive
harm.
WARNING

5
ASSEMBLY
There are several areas during the assembly process that special attention must be paid. It is very important to follow the
assembly instructions correctly and to make sure all parts are firmly tightened. If the assembly instructions are not followed
correctly, the exercise bike could have parts that are not tightened and will seem loose and may cause irritating noises. To
prevent damage to the exercise bike, the assembly instructions must be reviewed and corrective actions should be taken.
Before proceeding, find your exercise bike’s serial number and enter it in the space
provided below. The serial number will be located on a white sticker with a bar code.
ENTER YOUR SERIAL NUMBER AND MODEL NAME IN THE BOX BELOW:
» Refer to the SERIAL NUMBER and MODEL NAME when calling for service.
» Be sure to enter both the SERIAL NUMBER and MODEL NAME on your warranty card.
MODEL NAME: HORIZON EXERCISE BIKE
WARNING
SERIAL NUMBER:
SERIAL NUMBER LOCATION

6
COMFORT
U
HANDLEBARS
SEAT BACK
SEAT BASE
CRANK
REAR STABILIZER
FRONT STABILIZER TUBE
CONSOLE
CONSOLE MAST
PULSE GRIP HANDLEBARS
WATER BOTTLE HOLDER
SEAT POSITION
ADJUSTMENT LEVER
CONSOLE MAST GROMMET
MAIN FRAME
POWER CORD SOCKET
TRANSPORT WHEELS
PEDALS

7
COMFORT
R
TOOLS INCLUDED:
F13/15mm Flat Wrench
FPhillips Screwdriver/Allen Wrench
PARTS INCLUDED:
F1 Main Frame
F1 Console
F1 Console Mast
F1 Console Mast Grommet
F1 Water Bottle Holder
F1 Front Stabilizer
F1 Rear Stabilizer
F1 Seat Base
F1 Seat Back
F1 Seat Frame
F1 Seat Frame Cover
F1 Pulse Grip Handlebars
F2 Pedals with Straps
F1 Audio Adapter Cable
F1 Power Cord
F1 Hardware Kit
UNPACKING
Unpack the product where you will be using it. Place the bike carton
on a level flat surface. It is recommended that you place a protective
covering on your floor. Never open box when it is on its side.
If you have questions or if there are any missing parts, contact
Customer Tech Support. Contact information is located on the
back panel of this manual.
NEED HELP?
COMFORT R PRE ASSEMBLY
• During each assembly step, ensure that ALL nuts and bolts
are in place and partially threaded. It is recommended you
complete the full assembly of your unit before completely
tightening any ONE bolt.
• Several parts have been pre-lubricated to aid in assembly and
usage. Please do not wipe this off. If you have difficulty, a light
application of lithium bike grease is recommended.
IMPORTANT NOTES

8
COMFORT
R
COMFORT R ASSEMBLY STEP 1
A Open HARDWARE FOR STEP 1.
B Attach the REAR STABILIZER (1) to
the MAIN FRAME (2) using 2 BOLTS
(A), 2 FLAT WASHERS (B), 2 SPRING
WASHERS (C) and 2 NUTS (D).
C Attach the FRONT STABILIZER (3) to
the MAIN FRAME (2) using 2 BOLTS
(A), 2 FLAT WASHERS (B), 2 SPRING
WASHERS (C) and 2 NUTS (D).
1
2
3
D
C
B
A
HARDWARE FOR STEP 1
PART TYPE DESCRIPTION QTY
ABOLT M8X56 4
BFLAT WASHER Φ18X2.0T 4
CSPRING WASHER M8X2.0T 4
DNUT M8 4

9
COMFORT
R
HARDWARE FOR STEP 2
PART TYPE DESCRIPTION QTY
ESCREW M4X12 2
COMFORT R ASSEMBLY STEP 2
4
5
E
A Open HARDWARE FOR STEP 2.
B Slide WATER BOTTLE HOLDER (4) up
CONSOLE MAST (5) and align screw
holes in WATER BOTTLE HOLDER (4)
with holes in CONSOLE MAST (5).
C Attach the WATER BOTTLE HOLDER (4)
using 2 SCREWS (E).

10
COMFORT
R
COMFORT R ASSEMBLY STEP 3
A Open HARDWARE FOR STEP 3.
B Slide CONSOLE MAST GROMMET (6)
from the bottom up the CONSOLE MAST
(5).
C Attach CONSOLE CABLES (7) and
carefully tuck all cables into MAIN FRAME
(2). Slide CONSOLE MAST (5) into MAIN
FRAME (2).
D Attach the CONSOLE MAST (5) using 4
BOLTS (F) and 4 FLAT WASHERS (B)
from the front and 2 BOLTS (G) and from
the sides.
E Slide CONSOLE MAST GROMMET (6)
down over MAIN FRAME (2).
5
6
7
B
G
2
F
HARDWARE FOR STEP 3
PART TYPE DESCRIPTION QTY
FBOLT M8X60 4
BFLAT WASHER Φ18X2.0T 4
GBOLT M8X18 2