Horizon Fitness Adventure 4 Plus User manual

TREADMILL OWNER’S MANUAL
Read the TREADMILL GUIDE before using this OWNER’S MANUAL.
Adventure 4 Plus
Adventure 5 Plus

23
ASSEMBLY
There are several areas during the assembly process that special attention must be paid. It is very important to follow the assembly
instructions correctly and to make sure all parts are firmly tightened. If the assembly instructions are not followed correctly, the
treadmill could have frame parts that are not tightened and will seem loose and may cause irritating noises. To prevent damage
to the treadmill, the assembly instructions must be reviewed and corrective actions should be taken.
Before proceeding, find your treadmill’s serial number located on the front stabilizer tube and enter it in the space provided
below. Also locate the model name which is next to the serial number.
ENTER YOUR SERIAL NUMBER AND MODEL NAME IN THE BOXES BELOW:
WARNING
SERIAL NUMBER:
MODEL NAME: HoRIzoN TREADMILL

4 5
ALL
MoDELS
ALL
MoDELS
SPEAKERS
WATER BOTTLE HOLDER
GRIP PULSE HANDRAILS
SUPPORT BAR
CONSOLE FAN
ON/OFF SWITCH
CIRCUIT BREAKER
TRANSPORT WHEEL
POWER CORD
READING RACK
CONSOLE
IPOD/MP3 PLAYER POCKET
TOUCH PAD PANEL AND DISPLAY WINDOWS
SAFETY KEY PLACEMENT
MOTOR COVER
RUNNING BELT / RUNNING DECK
SIDE RAIL
ROLLER END CAP
REAR ROLLER
ADJUSTMENT BOLTS
CONSOLE MAST
FOOT LOCK LATCH (UNDERNEATH DECK)
TooLS INCLUDED:
F6 mm T-Wrench
F5 mm L-Wrench
F4 mm L-Wrench
F4 mm T-Wrench
PARTS INCLUDED:
F1 Console Assembly
F2 Console Masts
F2 Socket
F1 Support Bar
F5 Hardware Bags
F1 Safety Key
F1 Audio Adapter Cable
F1 Bottle of Silicone Lubricant
(for 2 applications)
F4 iPod® Dock Inserts (Adventure5 only)
F1 iPod® Dock Rubber Plug (Adventure5 only)
F1 Power Cord
DO NOT ATTEMPT TO LIFT THE TREADMILL! Do not move or lift treadmill
from packaging until specified to do so in the assembly instructions. You may
remove the plastic wrap from console masts.
WARNING
UNPACKING
Place the treadmill carton on a level flat surface. It is recommended that you place a
protective covering on your floor. Take CAUTION when handling and transporting this
unit. Never open box when it is on its side. Once the banding straps have been removed,
do not lift or transport this unit unless it is fully assembled and in the upright folded
position, with the lock latch secure. Unpack the unit where it will be used. The enclosed
treadmill is equipped with high-pressure shocks and may spring open if mishandled.
Never grab hold of any portion of the incline frame and attempt to lift or move the treadmill.
FAILURE TO FOLLOW THESE INSTRUCTIONS COULD RESULT IN INJURY!
WARNING
NOTE: During each assembly step, ensure that ALL nuts and bolts are in place and
partially threaded in before completely tightening any ONE bolt.
NOTE: A light application of grease may aid in the installation of hardware. Any grease,
such as lithium bike grease is recommended.
PRE ASSEMBLY

6 7
ALL
MoDELS
ALL
MoDELS
ASSEMBLY STEP 1
A Cut the yellow banding straps and lift the
running deck upward until the foot
latch locks. Remove all contents from
underneath the running deck.
B Open hardware bag 1.
C Attach the left Socket to the left
conSole maSt using 4 Socket boltS
(a).
D Attach the right Socket to the right
conSole maSt using 4 Socket boltS
(a).
SOCKET BOLT
10 mm
Qty: 8
HARDWARE BAG 1 CONTENTS :
SOCKET BOLT
CONSOLE MAST
SOCKET
ASSEMBLY STEP 2
A Open hardware bag 2.
B With the running deck in the raised
position, attach the left conSole maSt
to the baSe frame using 4 boltS (a),
4 Spring waSherS (b) and 4 flat
waSherS (c).
BOLT (A)
20 mm
Qty: 4
SPRING WASHER (B)
15 mm
Qty: 4
FLAT WASHER (C)
15 mm
Qty: 4
HARDWARE BAG 2 CONTENTS :
LEFT
CONSOLE
MAST
RUNNING DECK
RUNNING DECK
BASE FRAME
FOOT LATCH
BOLTS (A)
SPRING WASHERS (B)
FLAT WASHERS (C)

8 9
ALL
MoDELS
ASSEMBLY STEP 3
A Open hardware bag 3.
B Pull lead wire through right conSole
maSt. After pulling the lead wire through the
mast, the top of the conSole cable should
be located at the top of the mast. Detach and
discard the lead wire.
C With the running deck in the raised
position, attach the right conSole
maSt to the baSe frame using 4 boltS
(a), 4 Spring waSherS (b) and 4 flat
waSherS (c).
NOTE: Be careful not to pinch any wires
while assembling the right console mast.
BOLT (A)
20 mm
Qty: 4
SPRING WASHER (B)
15 mm
Qty: 4
FLAT WASHER (C)
15 mm
Qty: 4
HARDWARE BAG 3 CONTENTS :
BOLTS (A)
SPRING WASHERS (B)
FLAT WASHERS (C)
RIGHT CONSOLE MAST
CONSOLE CABLE
LEAD WIRE
BASE FRAME
RUNNING DECK
ASSEMBLY STEP 4
SPRING WASHER (B)
15 mm
Qty: 4
FLAT WASHER (C)
15 mm
Qty: 4
BOLT (D)
15 mm
Qty: 4
HARDWARE BAG 4 CONTENTS :
BOLTS (D)
CONSOLE MAST
CONSOLE CABLES
CONSOLE
ASSEMBLE
LEFT SIDE
FIRST
SPRING WASHERS (B)
FLAT WASHERS (C)
A Disengage the deck lock latch with your
foot to lower the running deck.
B Open hardware bag 4.
C Gently place the conSole on top of the
conSole maStS. Attach the left Side first
using 2 boltS (d), 2 Spring waSherS (b)
and 2 flat waSherS (c).
D Connect the conSole cableS, carefully
tucking wires in masts to avoid damage.
E Attach the right Side of the conSole
using 2 boltS (d), 2 Spring waSherS
(b) and 2 flat waSherS (c).
NOTE: Be careful not to pinch any wires
while assembling the masts.
ALL
MoDELS