Horizon Fitness HORIZON GS1050T TREADMILL GS1050T User manual

GS1050T
TREADMILL OWNER’S MANUAL
Read the TREADMILL GUIDE before using this OWNER’S MANUAL.

2

3
ASSEMBLY
There are several areas during the assembly process that special attention must be paid. It is very important to follow the assembly
instructions correctly and to make sure all parts are firmly tightened. If the assembly instructions are not followed correctly, the
treadmill could have parts that are not tightened and will seem loose and may cause irritating noises. To prevent damage to the
treadmill, the assembly instructions must be reviewed and corrective actions should be taken.
Before proceeding, find your treadmill’s serial number located below the
on/off power switch and power cord and enter it in the space provided below.
ENTER YOUR SERIAL NUMBER IN THE BOX BELOW:
» Refer to the SERIAL NUMBER and MODEL NAME when calling for service.
» Be sure to enter both the SERIAL NUMBER and MODEL NAME on your warranty card.
SERIAL NUMBER:
MODEL NAME: HORIZON GS1050T TREADMILL
WARNING

4
SPEAKERS
WATER BOTTLE HOLDER
GRIP PULSE HANDRAILS
SUPPORT BAR
CONSOLE FAN
ON/OFF SWITCH
CIRCUIT BREAKER
TRANSPORT WHEEL
POWER CORD
READING RACK
CONSOLE
IPOD/MP3 PLAYER POCKET
TOUCH PAD PANEL AND DISPLAY WINDOWS
SAFETY KEY PLACEMENT
MOTOR COVER
RUNNING BELT / RUNNING DECK
SIDE RAIL
ROLLER END CAP
REAR ROLLER
ADJUSTMENT BOLTS
CONSOLE MAST
FOOT LOCK LATCH
HANDLEBARS

5
TOOLS INCLUDED:
F4 mm L-wrench
F6 mm L-wrench
F10 mm L-wrench
F6 mm T-wrench
F17mm Flat Wrench
FScrewdriver
PARTS INCLUDED:
F1 Console Assembly
F2 Console Masts
F2 Handlebars
F2 Handlebar Boots
F1 Support Bar
F5 Hardware Bags
F1 Safety Key
F1 Power Cable
F1 Audio Adapter Cable
F1 Bottle of Silicone Lubricant
(for 2 applications)
If you have questions or if there
are any missing parts, contact
Customer Tech Support. Contact
information is located on the back
panel of this manual.
DO NOT ATTEMPT TO LIFT THE TREADMILL! Do not move or lift treadmill
from packaging until specified to do so in the assembly instructions. You may
remove the plastic wrap from console masts.
WARNING
UNPACKING
Place the treadmill carton on a level flat surface. It is recommended that you place a
protective covering on your floor. Take CAUTION when handling and transporting this
unit. Never open box when it is on its side. Once the banding straps have been removed,
do not lift or transport this unit unless it is fully assembled and in the upright folded
position, with the lock latch secure. Unpack the unit where it will be used. The enclosed
treadmill is equipped with high-pressure shocks and may spring open if mishandled.
Never grab hold of any portion of the incline frame and attempt to lift or move the treadmill.
FAILURE TO FOLLOW THESE INSTRUCTIONS COULD RESULT IN INJURY!
WARNING
NEED HELP?
NOTE: During each assembly step, ensure that ALL nuts and bolts are in place and
partially threaded in before completely tightening any ONE bolt.
NOTE: A light application of grease may aid in the installation of hardware. Any grease,
such as lithium bike grease is recommended.
PRE ASSEMBLY

6
ASSEMBLY STEP 1
A Open HARDWARE BAG 1.
B Cut banding straps. Do not move or lift treadmill
from packaging.
C Move LEFT LINKAGE ARM into position.
Insert BOLT (A) and FLAT WASHER (B) into
LEFT LINKAGE ARM followed by a TEFLON
WASHER (C) and attach to elevation frame.
D Lift LEFT CONSOLE MAST into upright
position. Be sure to hold the console mast
firmly, as it will not stay in the upright position on
its own.
E Insert BOLT (D) and 1 FLAT WASHER (E)
through LEFT CONSOLE MAST followed by
a WAVY WASHER (F) and attach to MAIN
FRAME.
FLAT WASHER (B)
20 mm
Qty: 1
WAVY WASHER (F)
29 mm
Qty: 1
BOLT (D)
Qty: 1
BOLT (A)
15 mm
Qty: 1
TEFLON WASHER (C)
18 mm
Qty: 1
FLAT WASHER (E)
27 mm
Qty: 1
HARDWARE BAG 1 CONTENTS :
BOLT (D)
FLAT WASHER (E)
WAVY WASHER (F)
MAIN FRAME
LEFT CONSOLE MAST
BOLT (A)
FLAT WASHER (B)
LEFT LINKAGE ARM
TEFLON WASHER (C)

7
ASSEMBLY STEP 2
A Pull LEAD WIRE through RIGHT CONSOLE MAST.
After pulling the lead wire through the mast, the top of the
CONSOLE CABLES should be located at the top of the
mast. Detach and discard LEAD WIRE.
B Open HARDWARE BAG 2.
C Move RIGHT LINKAGE ARM into position and attach to
ELEVATION FRAME. While holding RIGHT CONSOLE
MAST in the upright position, tighten PRE-ATTACHED
BOLT using flat wrench to attach RIGHT LINKAGE ARM.
D Attach RIGHT CONSOLE MAST to MAIN FRAME
using 1 BOLT (D), 1 FLAT WASHER (E) and 1 WAVY
WASHER (F).
E Lift the RUNNING DECK until FOOT LOCK LATCH on
side of treadmill is fully engaged.
F Remove CONSOLE from box and place out of the way.
G Lower the treadmill RUNNING DECK from the folded position
by stepping on FOOT LOCK LATCH on lower right side.
WAVY WASHER (F)
29 mm
Qty: 1
BOLT (D)
Qty: 1
FLAT WASHER (E)
27 mm
Qty: 1
HARDWARE BAG 2 CONTENTS :
BOLT (D)
FLAT WASHER (E)
WAVY WASHER (F)
CONSOLE CABLE
RIGHT CONSOLE MAST
LEAD WIRE
MAIN FRAME
RIGHT LINKAGE ARM
ELEVATION FRAME
PRE-ATTACHED BOLT
FOOT LOCK LATCH
If you have attempted to move the treadmill from the box and
the machine has sprung open and cannot be assembled, refer
to the troubleshooting section in the TREADMILL GUIDE in
order to restore the treadmill to its proper position.
ATTENTION
NOTE: Be
careful not to
pinch any wires
while assembling
the right console
mast.

8
ASSEMBLY STEP 3
SPRING WASHER (B)
15 mm
Qty: 4
FLAT WASHER (H)
20 mm
Qty: 4
BOLT (G)
15 mm
Qty: 4
HARDWARE BAG 3 CONTENTS :
CONSOLE CABLES
CONSOLE MAST
CONSOLE
SPRING WASHERS (B)
BOLTS (G)
FLAT WASHERS (H)
DO NOT ATTACH
THIS SIDE
UNTIL STEP 3-D
A Disengage the deck lock latch with your
foot to lower the running deck.
B Open hardware bag 3.
C Gently place the console on top of the
console masts. Attach the left side first
using 2 bolts (g), 2 spring washers (b)
and 2 flat washers (h).
NOTE: Do not completely tighten bolts (g)
until step 4-D.
D Connect the console cables, carefully
tucking wires in masts to avoid damage.
E Attach the right side of the console
using 2 bolts (d), 2 spring washers
(b) and 2 flat washers (c).
NOTE: Be careful not to pinch any wires
while attaching the console.

9
ASSEMBLY STEP 4
BOLT (I)
15 mm
Qty: 4
HARDWARE BAG 4 CONTENTS :
CONSOLE
CONSOLE MAST
BOLTS (I)
SUPPORT BAR
A Open hardware bag 4.
B Align support bar with holes in console
masts.
C Insert bolts (i) into all 4 holes of the
support bar.
NOTE: Look into holes in the right mast before
inserting bolts to avoid pinching cables.
D Tighten all console bolts (step 3) and
support bar bolts (step 4) completely.

10
ASSEMBLY STEP 5
BOLT (G)
15 mm
Qty: 2
FLAT WASHER (J)
15 mm
Qty: 2
BOLT (K)
12 mm
Qty: 2
HARDWARE BAG 5 CONTENTS :
CONSOLE
CONSOLE MAST
BOLTS (G)
FLAT WASHERS (J)
BOLTS (K)
HANDLEBAR
HANDLERBAR BOOT
A Open HARDWARE BAG 5.
B Slide left HANDLEBAR to CONSOLE and
attach using 1 BOLT (K).
C Slide HANDLEBAR BOOT UP over bottom of
HANDLEBAR.
D Attach left HANDLEBAR to CONSOLE MAST
using 1 BOLT (G) and 1 FLAT WASHER J).
E Slide HANDLEBAR BOOT down to cover
HANDLEBAR-MAST conection.
F Repeat on other side.
G Connect power plug to the treadmill and
connect the cord to a power outlet. The on/
off switch is located next to the power cord.
Flip this switch to the ‘ON’ position, so that
the switch is lit. You will hear a beep and the
console will turn on.
H Before the first use, lubricate the treadmill deck by
following the instructions in the MAINTENANCE
section in the TREADMILL GUIDE.
ASSEMBLY COMPLETE!