Horizon Fitness Elite T5 User manual

ASSEMBLY GUIDE
GUIDE D’ASSEMBLAGE
GUÍA DE ENSAMBLAJE
ELITE T5
T7
T9

2
3 ENGLISH
16 FRANÇAIS
30 ESPAÑOL

3
ASSEMBLY
There are several areas during the assembly process that special attention must be paid. It is very important to follow the assembly
instructions correctly and to make sure all parts are firmly tightened. If the assembly instructions are not followed correctly, the
treadmill could have parts that are not tightened and will seem loose and may cause irritating noises. To prevent damage to the
treadmill, the assembly instructions must be reviewed and corrective actions should be taken.
Before proceeding, find your treadmill’s serial number located on a white barcode sticker
near the on/off power switch and power cord and enter it in the space provided below.
ENTER YOUR SERIAL NUMBER AND MODEL NAME IN THE BOXES BELOW:
» Refer to the SERIAL NUMBER and MODEL NAME when calling for service.
SERIAL NUMBER:
TM
MODEL NAME: HORIZON TREADMILL
WARNING
SERIAL NUMBER LOCATION
ENGLISH

4
T5
T7
1
2
2
1
CONSOLE FAN
WATER BOTTLE HOLDER
CONSOLE
SPEAKERS
ON/OFF SWITCH
POWER CORD
TRANSPORT WHEEL
FOOT LOCK LATCH (UNDERNEATH DECK)
CONSOLE DISPLAY AND CONTROLS
SAFETY KEY PLACEMENT
HANDLEBARS
HEART RATE GRIP BARS
CONSOLE MAST
MOTOR COVER
RUNNING BELT / DECK
REAR ROLLER TENSION
& ADJUSTMENT BOLTS
SIDE RAIL
ENGLISH

5
1
2
2
1
CONSOLE DISPLAY AND CONTROLS
SAFETY KEY PLACEMENT
HANDLEBARS
HEART RATE GRIP BARS
CONSOLE MAST
MOTOR COVER
RUNNING BELT / DECK
REAR ROLLER TENSION
& ADJUSTMENT BOLTS
SIDE RAIL
T9
CONSOLE FAN
WATER BOTTLE HOLDER
CONSOLE
SPEAKERS
ON/OFF SWITCH
POWER CORD
TRANSPORT WHEEL
FOOT LOCK LATCH (UNDERNEATH DECK)
ENGLISH

6
TOOLS REQUIRED:
FT-Wrench
FL-Wrench
FPhillips Screwdriver (not included)
PARTS INCLUDED:
F1 Main Frame
F2 Console Masts
F1 Console
F2 Water Bottle Holders
F2 Handlebars
F2 Main Frame Covers
F2 Console Mast Covers
F1 Polar®Chest Strap (T7 only)
F1 Hardware Kit
F1 Safety Key
F1 Power Cord
F1 Audio Adapter Cable
If you have questions or if there
are any missing parts, contact
Customer Tech Support. Contact
information is located on the
back cover of this manual.
NEED HELP?
• DO NOT ATTEMPT TO LIFT THE TREADMILL! Do not move or lift treadmill from
packaging until specified to do so in the assembly instructions. You may remove the
plastic wrap from console masts.
• FAILURE TO FOLLOW THESE INSTRUCTIONS COULD RESULT IN INJURY!
WARNING
UNPACKING
Place the treadmill carton on a level flat surface. It is recommended that you place a
protective covering on your floor. Take CAUTION when handling and transporting this
unit. Never open box when it is on its side. Once the banding straps have been removed,
do not lift or transport this unit unless it is fully assembled and in the upright folded
position, with the lock latch secure. Unpack and assemble the unit where it will be used.
The enclosed treadmill is equipped with high-pressure shocks and may spring open if
mishandled. Never grab hold of any portion of the incline frame and attempt to lift or
move the treadmill.
PRE ASSEMBLY
• During each assembly step, ensure that ALL nuts and bolts are in place and partially
threaded. It is recommended you complete the full assembly of your unit before
completely tightening any ONE bolt.
• Several parts have been pre-lubricated to aid in assembly and usage. Please do
not wipe this off. If you have difficulty, a light application of lithium bike grease is
recommended.
IMPORTANT NOTES
ENGLISH

7
1
A
ASSEMBLY STEP 1
A Cut the yellow banding straps and lift the
running deck upward to remove all contents
from underneath the running deck.
B Open hardware for STEP 1.
C Insert 2 BOLTS (A) into MAIN FRAME (1).
HARDWARE FOR STEP 1
PART TYPE QTY
A HEX SOCKET BOLT 2
T7 SHOWN
ENGLISH

8
2
1
D
C
B
ASSEMBLY STEP 2
A Open HARDWARE FOR STEP 2.
B Attach LEFT CONSOLE MAST (2) to MAIN
FRAME (1) using 4 BOLTS (B), 4 SPRING
WASHERS (C) and 4 FLAT WASHERS (D).
HARDWARE FOR STEP 2
PART TYPE QTY
B BUTTON HEAD BOLT 4
CSPRING WASHER 4
DFLAT WASHER 4
NOTE: Do not fully tighten bolts until step 6.
T7 SHOWN
ENGLISH

9
A Pull the CONSOLE CABLE (3) away from the
treadmill base frame. Connect the CONSOLE
CABLE (3) from the MAIN FRAME (1) to the
CONSOLE CABLE (3) in the bottom of the
RIGHT CONSOLE MAST (4). The other end
of the CONSOLE CABLE should be located at
the top of the mast.
B Open HARDWARE FOR STEP 3.
C Attach RIGHT CONSOLE MAST (4) to MAIN
FRAME (1) using 4 BOLTS (B), 4 SPRING
WASHERS (C) and 4 FLAT WASHERS (D).
4
3
B
1
C
D
ASSEMBLY STEP 3
HARDWARE FOR STEP 3
PART TYPE QTY
B BUTTON HEAD BOLT 4
CSPRING WASHER 4
DFLAT WASHER 4
NOTE: Do not fully tighten bolts until step 6.
NOTE: Be careful not to pinch the console cable
while attaching the right console mast.
T7 SHOWN
ENGLISH

10
5
4
6
A T5 / T7 models only: Slide MAIN FRAME
COVERS (5) over CONSOLE MASTS (4).
B All models: Slide CONSOLE MAST COVERS (6)
over CONSOLE MASTS (4).
NO HARDWARE FOR STEP 4
ASSEMBLY STEP 4
T7 SHOWN
ENGLISH