Horizon Fitness ELITE T5000 User manual

TREADMILL OWNER’S MANUAL
Read the TREADMILL GUIDE before using this OWNER’S MANUAL.
Elite T5000

2

3
ASSEMBLY
There are several areas during the assembly process that special attention must be paid. It is very important to follow the assembly
instructions correctly and to make sure all parts are firmly tightened. If the assembly instructions are not followed correctly, the
treadmill could have frame parts that are not tightened and will seem loose and may cause irritating noises. To prevent damage
to the treadmill, the assembly instructions must be reviewed and corrective actions should be taken.
Before proceeding, find your treadmill’s serial number located on the front stabilizer tube and enter it in the space provided
below. Also locate the model name which is next to the serial number.
ENTER YOUR SERIAL NUMBER AND MODEL NAME IN THE BOXES BELOW:
WARNING
SERIAL NUMBER:
MODEL NAME: HoRIzoN TREADMILL

4
Elite
T5000 CONSOLE
ON/OFF SWITCH
CIRCUIT BREAKER
POWER CORD
CONSOLE CONTROLS AND DISPLAY WINDOWS
USB PORT AND AUDIO IN JACK
SAFETY KEY PLACEMENT
ROLLER END CAP
REAR ROLLER TENSION/ADJUSTMENT BOLTS
IN-REACH CONTROLS
SPEAKERS
WATER BOTTLE HOLDER
GRIP PULSE HANDRAILS
DROP-DOWN HANDLEBAR
TRANSPORT WHEEL
READING RACK / AUDIO CORD CHANNEL
HANDLEBARS
MOTOR COVER
SIDE RAIL
CONSOLE MAST
RUNNING BELT / RUNNING DECK

5
TooLS INCLUDED:
F8 mm T-Wrench
F5 mm T-Wrench
F5 mm L-Wrench
FScrewdriver
PARTS INCLUDED:
F1 Console Assembly
F2 Console Masts
F1 Hardware Kit
F1 Safety Key
F1 Power Cord
F1 Audio Adapter Cable
If you have questions or if
there are any missing parts,
contact your local dealer.
NEED HELP?
DO NOT ATTEMPT TO LIFT THE TREADMILL! Do not move or lift treadmill
from packaging until specified to do so in the assembly instructions. You may
remove the plastic wrap from console masts.
WARNING
UNPACKING
Place the treadmill carton on a level flat surface. It is recommended that you place a
protective covering on your floor. Take CAUTION when handling and transporting this
unit. Never open box when it is on its side. Once the banding straps have been removed,
do not lift or transport this unit unless it is fully assembled. Unpack and assemble the unit
where it will be used. Never grab hold of any portion of the incline frame and attempt to
lift or move the treadmill.
FAILURE TO FOLLOW THESE INSTRUCTIONS COULD RESULT IN INJURY!
WARNING
NOTE: During each assembly step, ensure that ALL nuts and bolts are in place and
partially threaded in before completely tightening any ONE bolt.
NOTE: A light application of grease may aid in the installation of hardware. Any grease,
such as lithium bike grease is recommended.
PRE ASSEMBLY
Elite
T5000

6
HARDWARE foR STEP 1 :
ASSEMBLY STEP 1
A Open HARDWARE FOR STEP 1.
B Attach CONSOLE MAST COVER to main frame
using 3 screws each side.
SCREW (1)
Φ 4 x 20
Qty: 2
SCREW (1-1)
M4 x 12
Qty: 4
Elite
T5000
SCREW (1)
LEFT CONSOLE MAST
SCREW (1-1)
RIGHT CONSOLE MAST

7
ASSEMBLY STEP 2
BOLT (A)
M8 x 20 mm
Qty: 6
SPRING WASHER (B)
8.2 mm
Qty: 6
ARC WASHER (C)
Φ8.2 x Φ17
Qty: 6
HARDWARE foR STEP 2 : A Open HARDWARE FOR STEP 2.
B Pull LEAD WIRE through RIGHT CONSOLE MAST.
After pulling the LEAD WIRE through the mast, the
top of the CONSOLE CABLE should be located at
the top of the mast. Detach and discard LEAD WIRE.
N
C Attach CONSOLE MAST to MAIN FRAME
BRACKET using 3 BOLTS (A), 3 SPRING
WASHERS (B) and 3 ARC WASHERS (C).
D Repeat step C on other side.
NOTE: Do not tighten bolts until step 3 is complete.
NOTE: Do not pinch console cable when placing
the mast onto the main frame bracket.
Elite
T5000
BOLTS (A)
SPRING WASHERS (B)
LEFT CONSOLE MAST
LEAD WIRE
CONSOLE CABLE
ARC WASHERS (C)
MAIN FRAME BRACKET
RIGHT CONSOLE MAST

8
A Open HARDWARE FOR STEP 3.
B CONNECT HANDLEBAR CABLES, and slide
HANDLEBARS into CENTER BAR.
C Attach HANDLEBARS to CENTER BAR using 4
BOLTS (E), 4 SPRING WASHERS (F) and 4 ARC
WASHERS (G).
NOTE: Do not pinch wires while attaching the
handlebars. Please do not tighten the screws of
handlebar, tighten them when assembly process
is completed.
BOLT (E)
M6 x 10 mm
Qty: 4
SPRING WASHER (F)
6.2 mm
Qty: 4
ARC WASHER (G)
Φ6.2 x Φ14
Qty: 4
ASSEMBLY STEP 3
HARDWARE foR STEP 3 :
Elite
T5000
CONSOLE CABLES
HANDLEBARS
CENTER BAR
BOLTS (E)
SPRING WASHERS (F)
ARC WASHERS (G)

9
ASSEMBLY STEP 4
A Open HARDWARE FOR STEP 4.
B With the CONSOLE upside down, attach the
CONSOLE MAST CAPS to the CONSOLE
using 6 BOLTS (J) , 6 SPRING WASHERS
(B) and 6 FLAT WASHERS (I).
BOLT (J)
M8 x 20 mm
Qty: 6
FLAT WASHER (I)
Φ8.2 x Φ16
Qty: 6
SPRING WASHER (B)
8.2 mm
Qty: 6
HARDWARE foR STEP 4 :
Elite
T5000
FLAT WASHERS (I)
CONSOLE MAST CAP
SPRING WASHERS (B)
BOLTS (J)
CONSOLE (upside down)

10
NOTE: Be careful not to pinch any wires while
assembling.
ASSEMBLY STEP 5
HARDWARE BAG 5:A Open HARDWARE FOR STEP 5.
B Gently place the CONSOLE on top of the
CONSOLE MASTS. Attach the LEFT SIDE first
using 3 BOLTS (J), 3 SPRING WASHERS (B)
and 3 ARC WASHERS (C).
C Connect the CONSOLE CABLES, carefully
tucking wires in masts to avoid damage.
D Attach the RIGHT SIDE of the CONSOLE
using 3 BOLTS (J), 3 SPRING WASHERS (B)
and 3 ARC WASHERS (C).
Elite
T5000
BOLTS (J)
SPRING WASHERS (B)
ARC WASHERS (C)
CONSOLE MAST
ASSEMBLE
THIS SIDE
FIRST
CONSOLE MAST CAP
CONSOLE
CONSOLE CABLES
BOLT (J)
M8 x 20mm
Qty: 6
SPRING WASHER (B)
8.2 mm
Qty: 6
ARC WASHER (C)
Φ8.2 x Φ17
Qty: 6