Hover-1 HY-H1 User manual

OPERATION MANUAL
HY-H1
ELECTRIC SCOOTER
All manuals and user guides at all-guides.com
all-guides.com

HELMETS
SAVE
LIVES!
Always wear a properly tted helmet that
complies with CPSC or CE safety standards
when you ride your bicycle.
Correct Fitting:
Make sure your helmet
covers your forehead.
Incorrect Fitting:
Forehead is exposed
and vulnerable to
serious injury.
1
All manuals and user guides at all-guides.com

PLEASE READ THE USER MANUAL THOROUGHLY.
Failure to follow the basic instructions and safety precautions listed in
the user manual can lead to damage to your device, other property
damage, serious bodily injury, and even death.
Thank you for purchasing the Hover-1 H1 Electric Scooter. Please read
all instructions carefully before using and retain this manual for future
use and reference.
This manual applies to the Hover-1 H1 Scooter.
• In order to avoid dangers that are caused by collisions, falls, and loss
of control, please learn how to ride the H1 safely.
• You can learn operating skills by reading the product manual and
watching videos.
• This manual includes all operating instructions and precautions, and
users must read it carefully and follow the instructions.
• All users are responsible for any consequences caused by
violating warning contents or prompt operations. Hover-1 can not
be held liable.
ATTENTION
1. Use only the supplied charger with this scooter.
Charger Manufacturer:
SHENZHEN FUYUANDIAN POWER CO LTD
Model: FY0634201500
2. The operating temperature range of the charger is 32° F-104° F
(0-40° C).
3. The operating temperature range of the Hover-1 is 32-104° F (0-40° C).
4. Do not ride on icy or slippery surfaces.
5. Read the user manual and warning labels before riding.
6. Store the H1 in a dry, ventilated environment.
7. When transporting the H1, avoid violent crashes or impact.
WARNING!
LOW TEMPERATURE WARNING
Low temperature will affect the lubrication of moving parts inside the
H1 scooter, increasing internal resistance. At the same time, in low
temperatures, the discharge capacity and the capacity itself of the
battery will be significantly decreased.
Use caution when riding the H1 in cold temperatures (below 40
degrees F).
Operating in low temperatures may increase the risk of mechanical
failures of the scooter, which may lead to damage to your device,
other property damage, serious bodily injury and even death.
SAFETY INSTRUCTIONS
• Keep the device away from heat sources, direct sunlight, humidity,
and prolonged exposure to water.
• Do not operate the device if it has been exposed to water, moisture
or any other liquids to prevent against electric shock, explosion
and/or injury to yourself and damage to the device.
• Do not use the device if it has been dropped or damaged in
any way.
• Repairs to electrical equipment should only be performed by a
qualified electrician. Improper repairs may place the user at
serious risk.
• Do not puncture or harm the exterior surface of the product in
any way.
• Keep the device free from dust, lint, etc.
• Do not use this device for anything other than its intended use or
purpose. Doing so may damage the device.
• This product is not a toy. Keep out of reach of children.
• Do not expose batteries, battery pack, or batteries installed to
excessive heat, such as direct sunlight, or open flame.
• Do not allow hands, feet, hair, body parts, clothing or similar
articles to come in contact with moving parts, wheels or drivetrain,
while the engine is running.
2
All manuals and user guides at all-guides.com

PLEASE READ THE USER MANUAL THOROUGHLY.
Failure to follow the basic instructions and safety precautions listed in
the user manual can lead to damage to your device, other property
damage, serious bodily injury, and even death.
Thank you for purchasing the Hover-1 H1 Electric Scooter. Please read
all instructions carefully before using and retain this manual for future
use and reference.
This manual applies to the Hover-1 H1 Scooter.
• In order to avoid dangers that are caused by collisions, falls, and loss
of control, please learn how to ride the H1 safely.
• You can learn operating skills by reading the product manual and
watching videos.
• This manual includes all operating instructions and precautions, and
users must read it carefully and follow the instructions.
• All users are responsible for any consequences caused by
violating warning contents or prompt operations. Hover-1 can not
be held liable.
ATTENTION
1. Use only the supplied charger with this scooter.
Charger Manufacturer:
SHENZHEN FUYUANDIAN POWER CO LTD
Model: FY0634201500
2. The operating temperature range of the charger is 32° F-104° F
(0-40° C).
3. The operating temperature range of the Hover-1 is 32-104° F (0-40° C).
4. Do not ride on icy or slippery surfaces.
5. Read the user manual and warning labels before riding.
6. Store the H1 in a dry, ventilated environment.
7. When transporting the H1, avoid violent crashes or impact.
LOW TEMPERATURE WARNING
Low temperature will affect the lubrication of moving parts inside the
H1 scooter, increasing internal resistance. At the same time, in low
temperatures, the discharge capacity and the capacity itself of the
battery will be significantly decreased.
Use caution when riding the H1 in cold temperatures (below 40
degrees F).
Operating in low temperatures may increase the risk of mechanical
failures of the scooter, which may lead to damage to your device,
other property damage, serious bodily injury and even death.
SAFETY INSTRUCTIONS
• Keep the device away from heat sources, direct sunlight, humidity,
and prolonged exposure to water.
• Do not operate the device if it has been exposed to water, moisture
or any other liquids to prevent against electric shock, explosion
and/or injury to yourself and damage to the device.
• Do not use the device if it has been dropped or damaged in
any way.
• Repairs to electrical equipment should only be performed by a
qualified electrician. Improper repairs may place the user at
serious risk.
• Do not puncture or harm the exterior surface of the product in
any way.
• Keep the device free from dust, lint, etc.
• Do not use this device for anything other than its intended use or
purpose. Doing so may damage the device.
• This product is not a toy. Keep out of reach of children.
• Do not expose batteries, battery pack, or batteries installed to
excessive heat, such as direct sunlight, or open flame.
• Do not allow hands, feet, hair, body parts, clothing or similar
articles to come in contact with moving parts, wheels or drivetrain,
while the engine is running.
3
All manuals and user guides at all-guides.com

• Do not operate, or allow others to operate, the Hover-1, until the
user understands all instructions, warnings and safety features
described in this manual.
• Check with your doctor if you have a medical condition that could
affect your ability to use the H1
• Persons with head, back or neck ailments or prior surgeries to
those areas of the body should not use the H1.
• Persons with any mental or physical conditions that may make
them susceptible to injury or impair their physical or mental
capabilities to recognize, understand and perform all of the
safety instructions and to be able to assume the hazards inherent
in unit use, should not use the H1.
In this manual, the above symbol with the word “NOTES” indicates
instructions or relevant facts the user should remember prior to using
the device.
In this manual, the above symbol with the word “CAUTION” indicates
a hazardous situation which, if not avoided, can cause minor or
moderate injury.
In this manual, the above symbol with the word “WARNING” indicates
a hazardous situation which, if not avoided, can cause death or
serious injury.
Please keep your serial number on file for warranty claims as well as
proof of purchase. Your serial number can be found at the base of
your H1 scooter above the holographic UL sticker.
WARNING!
SERIAL NUMBER
CAUTION!
NOTES:
4
All manuals and user guides at all-guides.com

OPERATING PRINCIPALS
The device uses digital electronic gyroscopes and acceleration
sensors to control balance and motion, depending on the user's
center of gravity. The device also uses a control system to drive the
motors that are located within the wheels. The device has a built-in
inertia dynamic stabilization system that can help assist with balance
when moving forward and backwards, but not while turning.
TIP – To increase your stability, you must shift your weight in order to
overcome the centrifugal force during turns, especially when
entering a turn at higher speeds.
Model: HY-H1
Net Weight: 22.04 lbs (10 kg)
Load: 44-265 lbs (20-120 kg)
Max Speed: Up to 9 mph (14.4 km/h)
Max Distance Range: Up to 9 miles (14.4 km)
Max Incline Angle: 15°
Minimum Turning Radius: 0°
Battery Type: Lithium-ion
Battery Voltage: 36 V
Battery Capacity: 4.0 Ah
Power Requirement: AC 100-240V, 50-60 Hz
Wheel Size: 6.5 Inches (16.51 cm)
Tire Type: Non-Pneumatic Solid Tires
IP Rating: IPX4
Bluetooth Range: Up to 33ft
Bluetooth Speaker: V2.0 with stereo sound quality
UL Certification: UL 2272 approved
FCC ID: 2AANZH1
BT ID: D037690
1 1
6 6
7 7
2345
10
8 9
The Hover-1 H1 is a personal transporter. Our technology and
production processes are developed with strict testing for each
Hover-1 scooter. Riding without following the contents of this manual
may lead to damage to your device, or may cause bodily injury.
This manual is designed to give you the information you need for the
safe operation and maintenance of your H1. Please read it thoroughly
before riding your H1.
PACKAGE CONTENTS
• Hover-1 H1 Electric Scooter
• 3-pin Charge Cable
• Operation Manual
(22.04 lb / 10 kg)
FEATURES/PARTS
1. Fender 6. Path Illuminating Lights
2. Left Foot Mat 7. LED Light
3. LED Status Indicator 8. Charge Port (Located in rear)
4. Power/Battery Indicator 9. Power Button (Located in rear)
5. Right Foot Mat 10. Protective Chassis Casing
INTRODUCTION
5
All manuals and user guides at all-guides.com
all-guides.com

OPERATING PRINCIPALS
The device uses digital electronic gyroscopes and acceleration
sensors to control balance and motion, depending on the user's
center of gravity. The device also uses a control system to drive the
motors that are located within the wheels. The device has a built-in
inertia dynamic stabilization system that can help assist with balance
when moving forward and backwards, but not while turning.
TIP – To increase your stability, you must shift your weight in order to
overcome the centrifugal force during turns, especially when
entering a turn at higher speeds.
Model: HY-H1
Net Weight: 22.04 lbs (10 kg)
Load: 44-265 lbs (20-120 kg)
Max Speed: Up to 9 mph (14.4 km/h)
Max Distance Range: Up to 9 miles (14.4 km)
Max Incline Angle: 15°
Minimum Turning Radius: 0°
Battery Type: Lithium-ion
Battery Voltage: 36 V
Battery Capacity: 4.0 Ah
Power Requirement: AC 100-240V, 50-60 Hz
Wheel Size: 6.5 Inches (16.51 cm)
Tire Type: Non-Pneumatic Solid Tires
IP Rating: IPX4
Bluetooth Range: Up to 33ft
Bluetooth Speaker: V2.0 with stereo sound quality
UL Certification: UL 2272 approved
FCC ID: 2AANZH1
BT ID: D037690
The Hover-1 H1 is a personal transporter. Our technology and
production processes are developed with strict testing for each
Hover-1 scooter. Riding without following the contents of this manual
may lead to damage to your device, or may cause bodily injury.
This manual is designed to give you the information you need for the
safe operation and maintenance of your H1. Please read it thoroughly
before riding your H1.
PACKAGE CONTENTS
• Hover-1 H1 Electric Scooter
• 3-pin Charge Cable
• Operation Manual
(22.04 lb / 10 kg)
FEATURES/PARTS
1. Fender 6. Path Illuminating Lights
2. Left Foot Mat 7. LED Light
3. LED Status Indicator 8. Charge Port (Located in rear)
4. Power/Battery Indicator 9. Power Button (Located in rear)
5. Right Foot Mat 10. Protective Chassis Casing
SPECIFICATIONS
WARNING
Any H1 scooter that does not work
properly can cause you to lose control
and fall. Inspect the entire device
thoroughly before every ride, and do
not ride it until any problems have
been corrected.
6
All manuals and user guides at all-guides.com

PLEASE READ THE FOLLOWING INSTRUCTIONS CAREFULLY
TURNING YOUR DEVICE ON/OFF
Power On: Take your device out of the box and place it flat on a level
surface. Press the power button (located on the rear of your device)
once. Check the battery LED indicator (located in the center of your
device). The battery indicator light should be lit, indicating the device
is powered on.
Power Off: Press the power button once.
MAT SENSOR
There are four sensors under the foot mats on your H1 scooter. When
the user steps off the scooter mats, it will automatically initiate
self-calibration.
When riding the scooter, you must ensure you are stepping on the foot
mats. Do not step or stand on any other area of your scooter.
Do not put items on the foot mats. Doing so will make the H1 turn on,
and increase the probability of collision and cause injury to people,
riders, or damage the device.
BATTERY INDICATOR
The display board is located in the middle of the H1 scooter.
• Green LED light indicates the device is charged above 20 percent.
• Yellow LED light indicates the power is under 20 percent.
• Red LED light indicates the power is down to 10 percent or lower.
When the LED light turns red, please recharge the device.
STATUS INDICATOR
When the operator triggers the foot mats, the LED Status Indicator will
light up, which indicates that the Hover-1 is now ready for use.
When the system has an error during operation, the status LED light will
turn red (for more details see SAFETY ALERTS).
CONTROLS AND DISPLAY
7
All manuals and user guides at all-guides.com

Your H1 is an App-enabled scooter that works with most mobile
devices. You must download the Hover-1 app in order to change
certain features of your H1 such as headlight colors and skill mode.
Please download the App from either the App Store or download
the App from the Google Play Store.
USING THE APP
Launch the app from your device, you will be directed to the intro
page. You may register your H1 by pressing the “Registration”. You
may continue to the dashboard by pressing “Skip”.
Please note, we encourage you to register your H1 scooter. For this
purpose, the intro page will continue to show every time the App is
launched if registration has not been completed. Once registration is
completed, the App will open directly to the dashboard.
1) REGISTRATION
Complete the form by entering your information to register your H1.
Fields marked with a “*” are required fields and the form cannot be
submitted without this information. Once you submit the registration
form, the safety, legal and privacy disclaimers will need to be
reviewed and accepted before moving on to the dashboard. Once
accepted, press “Next.”
SMART PHONE APP
2) DASHBOARD
Before allowing you to access the dashboard, a safety screen will
pop-up for 3 seconds. Please review the safety notes in this screen
while the dashboard loads. The dashboard will appear as shown
below.
1. Connect Your H1 - To connect to your H1 through Bluetooth on your
smart phone, press “Connect”. If your H1 is already paired, this part of
the screen will show “Connected” in blue.
2. Settings - Press the gear icon to adjust settings.
3. Speed - The digital speedometer displays your speed in miles per
hour.
4. Change Mode - Change safety/skill levels and H1 sensitivity.
5. Battery - The percentage displays the remaining battery life of your
H1.
6. Standby Mode - Put your H1 into a low-power mode when not in
use.
7. Customize Headlights - Change the colors and brightness of your
Path Illuminating Lights.
8. Vehicle - Displays the name assigned to your H1.
9. Vehicle Info - Swipe up from the bottom of your screen to display
more information about your H1 in real time.
10. GPS Tracking - View GPS & tracking to see where you have ridden
your H1 and display your real time location.
3) CONNECT
Press “Connect” to have the App begin scanning for any Hover-1
devices. Your H1 must be powered on and your smart phone’s
Bluetooth must be enabled. If your Bluetooth is not enabled on your
smart phone, the App will remind you to enable it.
Once scanning is complete, all detected Hover-1 scooters will display
in a list. Press the select button to pair with a scooter and use the PIN
“000000”. If multiple Hover-1 scooters appear, continue attempting to
pair until your H1 is paired.
Once paired, the dashboard will display “Connected” in blue. You
may now begin using the App with your H1.
4) SETTINGS
Press the gear icon to change settings for your H1.
• Change Vehicle’s Name - Customize the name for your H1 here. This
name change will reflect in the dashboard and connect pages.
• Set Auto Shutdown Time - This setting allows you to set a time for your
H1 to shutdown automatically.
• F.A.Q. - Frequently asked questions and answers are shown here
such as basic instructions and troubleshooting.
• Customer Service - View contact information for the Hover-1
customer service team.
• Terms & Conditions - Safety, legal and privacy disclaimers are here
for reference.
• App Version - Display the current App version and check for any
updates.
Next
Safety Disclaimer
Click to Accept
PLEASE READ THE MANUAL THOROUGHLY.
Failure to follow the basic instructions and safety
precautions listed in the user manual can lead to damage
to your device, other property damage, serious bodily
injury, and even death.
Thank you for purchasing the Hover-1 Electric Scooter.
Terms of Service
All sections of these Terms of Use that, by their nature,
should survive termination will survive termination,
including, without limitation, the sections entitled User
Content, Indemnity, Disclaimer of Warranty and Limitation
of Liability, and General.
Legal Disclaimer
Click to Accept
• Hardware/Software Version - Display the hardware and software
versions of your H1. These fields will only appear when connected to
your H1 scooter.
• Diagnostics - Run a diagnostic check on your H1 and stay informed
of any hardware, software and electrical issues that may need to be
addressed.
5) SKILL/SAFETY MODES
Cycle between 3 different skill modes. Each mode has a different top
speed and sensitivity. The mode will only change if you are not using
your H1 scooter.
• Beginner Mode - This mode is recommended for first time Hover-1
scooter users. In this mode, the sensitivity and top speed are very low.
• Intermediate Mode - This mode is recommended for users that are
comfortable using Hover-1 scooters but are not ready for full speed
and extra sensitive controls. In this mode, the sensitivity and top speed
are moderate.
• Expert Mode - This mode is recommended for everyday Hover-1
scooter users. In this mode, the sensitivity and top speed are set to the
maximum setting.
NOTE: Skill and safety mode must be selected. The Hover-1 will default
to “Beginner” mode if another mode is not selected.
6) STANDBY MODE
“Standby Mode” allows you to put your H1 into a low-power standby
state. Your H1 cannot be used while in standby. You must disable
standby mode before you can ride the H1. When in standby mode,
the button will say “Power On”. Press “Power On” to disable the
standby mode.
Please note, if you have your “Auto Shutdown Time” set, your H1 will
turn off completely at the specified time. You will be unable to power
it back on from the App. You will have to physically press the power
button on your H1 to turn it back on.
7) HEADLIGHTS
Press “Headlights” to set a custom color for your H1’s Path Illumination
Lights. Simply choose your desired color from the color wheel. For your
convenience, 4 basic colors have also been set as presets below the
brightness bar.
8) GPS
Press “GPS” to open a navigation screen that pin-points your exact
location. From the moment you press “Start”, it begins recording your
travel route. Once you press “Finish”, your route is saved in the App.
Press the bar icon, in the top right corner of your screen, to view all
saved travel routes.
By selecting one of the saved routes, you can view the details. Press
“...” to share or delete the route.
8
Submit
*Name
*Email Address
Age
*Serial Number (13 digit number)
Date of Purchase (mm/dd/yyyy)
Retailer
(*) Fields are required
h1
ELECTRIC SCOOTER
All manuals and user guides at all-guides.com

Your H1 is an App-enabled scooter that works with most mobile
devices. You must download the Hover-1 app in order to change
certain features of your H1 such as headlight colors and skill mode.
Please download the App from either the App Store or download
the App from the Google Play Store.
USING THE APP
Launch the app from your device, you will be directed to the intro
page. You may register your H1 by pressing the “Registration”. You
may continue to the dashboard by pressing “Skip”.
Please note, we encourage you to register your H1 scooter. For this
purpose, the intro page will continue to show every time the App is
launched if registration has not been completed. Once registration is
completed, the App will open directly to the dashboard.
1) REGISTRATION
Complete the form by entering your information to register your H1.
Fields marked with a “*” are required fields and the form cannot be
submitted without this information. Once you submit the registration
form, the safety, legal and privacy disclaimers will need to be
reviewed and accepted before moving on to the dashboard. Once
accepted, press “Next.”
2) DASHBOARD
Before allowing you to access the dashboard, a safety screen will
pop-up for 3 seconds. Please review the safety notes in this screen
while the dashboard loads. The dashboard will appear as shown
below.
1. Connect Your H1 - To connect to your H1 through Bluetooth on your
smart phone, press “Connect”. If your H1 is already paired, this part of
the screen will show “Connected” in blue.
2. Settings - Press the gear icon to adjust settings.
3. Speed - The digital speedometer displays your speed in miles per
hour.
4. Change Mode - Change safety/skill levels and H1 sensitivity.
5. Battery - The percentage displays the remaining battery life of your
H1.
6. Standby Mode - Put your H1 into a low-power mode when not in
use.
7. Customize Headlights - Change the colors and brightness of your
Path Illuminating Lights.
8. Vehicle - Displays the name assigned to your H1.
9. Vehicle Info - Swipe up from the bottom of your screen to display
more information about your H1 in real time.
10. GPS Tracking - View GPS & tracking to see where you have ridden
your H1 and display your real time location.
3) CONNECT
Press “Connect” to have the App begin scanning for any Hover-1
devices. Your H1 must be powered on and your smart phone’s
Bluetooth must be enabled. If your Bluetooth is not enabled on your
smart phone, the App will remind you to enable it.
Once scanning is complete, all detected Hover-1 scooters will display
in a list. Press the select button to pair with a scooter and use the PIN
“000000”. If multiple Hover-1 scooters appear, continue attempting to
pair until your H1 is paired.
Once paired, the dashboard will display “Connected” in blue. You
may now begin using the App with your H1.
4) SETTINGS
Press the gear icon to change settings for your H1.
• Change Vehicle’s Name - Customize the name for your H1 here. This
name change will reflect in the dashboard and connect pages.
• Set Auto Shutdown Time - This setting allows you to set a time for your
H1 to shutdown automatically.
• F.A.Q. - Frequently asked questions and answers are shown here
such as basic instructions and troubleshooting.
• Customer Service - View contact information for the Hover-1
customer service team.
• Terms & Conditions - Safety, legal and privacy disclaimers are here
for reference.
• App Version - Display the current App version and check for any
updates.
7.8
mph
Mode: Intermediate
Standby Mode
TRIP 12.4 milesODO 9.3 miles
Headlights Vehicle
Kevin’s Hover 1
Connected
GPS
Battery: 65%
h1
ELECTRIC SCOOTER
• Hardware/Software Version - Display the hardware and software
versions of your H1. These fields will only appear when connected to
your H1 scooter.
• Diagnostics - Run a diagnostic check on your H1 and stay informed
of any hardware, software and electrical issues that may need to be
addressed.
5) SKILL/SAFETY MODES
Cycle between 3 different skill modes. Each mode has a different top
speed and sensitivity. The mode will only change if you are not using
your H1 scooter.
• Beginner Mode - This mode is recommended for first time Hover-1
scooter users. In this mode, the sensitivity and top speed are very low.
• Intermediate Mode - This mode is recommended for users that are
comfortable using Hover-1 scooters but are not ready for full speed
and extra sensitive controls. In this mode, the sensitivity and top speed
are moderate.
• Expert Mode - This mode is recommended for everyday Hover-1
scooter users. In this mode, the sensitivity and top speed are set to the
maximum setting.
NOTE: Skill and safety mode must be selected. The Hover-1 will default
to “Beginner” mode if another mode is not selected.
6) STANDBY MODE
“Standby Mode” allows you to put your H1 into a low-power standby
state. Your H1 cannot be used while in standby. You must disable
standby mode before you can ride the H1. When in standby mode,
the button will say “Power On”. Press “Power On” to disable the
standby mode.
Please note, if you have your “Auto Shutdown Time” set, your H1 will
turn off completely at the specified time. You will be unable to power
it back on from the App. You will have to physically press the power
button on your H1 to turn it back on.
7) HEADLIGHTS
Press “Headlights” to set a custom color for your H1’s Path Illumination
Lights. Simply choose your desired color from the color wheel. For your
convenience, 4 basic colors have also been set as presets below the
brightness bar.
8) GPS
Press “GPS” to open a navigation screen that pin-points your exact
location. From the moment you press “Start”, it begins recording your
travel route. Once you press “Finish”, your route is saved in the App.
Press the bar icon, in the top right corner of your screen, to view all
saved travel routes.
By selecting one of the saved routes, you can view the details. Press
“...” to share or delete the route.
3
4
5
1
7
2
6
10
9
8
9
All manuals and user guides at all-guides.com

Your H1 is an App-enabled scooter that works with most mobile
devices. You must download the Hover-1 app in order to change
certain features of your H1 such as headlight colors and skill mode.
Please download the App from either the App Store or download
the App from the Google Play Store.
USING THE APP
Launch the app from your device, you will be directed to the intro
page. You may register your H1 by pressing the “Registration”. You
may continue to the dashboard by pressing “Skip”.
Please note, we encourage you to register your H1 scooter. For this
purpose, the intro page will continue to show every time the App is
launched if registration has not been completed. Once registration is
completed, the App will open directly to the dashboard.
1) REGISTRATION
Complete the form by entering your information to register your H1.
Fields marked with a “*” are required fields and the form cannot be
submitted without this information. Once you submit the registration
form, the safety, legal and privacy disclaimers will need to be
reviewed and accepted before moving on to the dashboard. Once
accepted, press “Next.”
2) DASHBOARD
Before allowing you to access the dashboard, a safety screen will
pop-up for 3 seconds. Please review the safety notes in this screen
while the dashboard loads. The dashboard will appear as shown
below.
1. Connect Your H1 - To connect to your H1 through Bluetooth on your
smart phone, press “Connect”. If your H1 is already paired, this part of
the screen will show “Connected” in blue.
2. Settings - Press the gear icon to adjust settings.
3. Speed - The digital speedometer displays your speed in miles per
hour.
4. Change Mode - Change safety/skill levels and H1 sensitivity.
5. Battery - The percentage displays the remaining battery life of your
H1.
6. Standby Mode - Put your H1 into a low-power mode when not in
use.
7. Customize Headlights - Change the colors and brightness of your
Path Illuminating Lights.
8. Vehicle - Displays the name assigned to your H1.
9. Vehicle Info - Swipe up from the bottom of your screen to display
more information about your H1 in real time.
10. GPS Tracking - View GPS & tracking to see where you have ridden
your H1 and display your real time location.
3) CONNECT
Press “Connect” to have the App begin scanning for any Hover-1
devices. Your H1 must be powered on and your smart phone’s
Bluetooth must be enabled. If your Bluetooth is not enabled on your
smart phone, the App will remind you to enable it.
Once scanning is complete, all detected Hover-1 scooters will display
in a list. Press the select button to pair with a scooter and use the PIN
“000000”. If multiple Hover-1 scooters appear, continue attempting to
pair until your H1 is paired.
Once paired, the dashboard will display “Connected” in blue. You
may now begin using the App with your H1.
4) SETTINGS
Press the gear icon to change settings for your H1.
• Change Vehicle’s Name - Customize the name for your H1 here. This
name change will reflect in the dashboard and connect pages.
• Set Auto Shutdown Time - This setting allows you to set a time for your
H1 to shutdown automatically.
• F.A.Q. - Frequently asked questions and answers are shown here
such as basic instructions and troubleshooting.
• Customer Service - View contact information for the Hover-1
customer service team.
• Terms & Conditions - Safety, legal and privacy disclaimers are here
for reference.
• App Version - Display the current App version and check for any
updates.
LOADING...
Remember to always wear
protective gear while riding your Hover-1
Remember to be alert at all times
and be aware of your surroundings
SAFETY SCREEN
• Hardware/Software Version - Display the hardware and software
versions of your H1. These fields will only appear when connected to
your H1 scooter.
• Diagnostics - Run a diagnostic check on your H1 and stay informed
of any hardware, software and electrical issues that may need to be
addressed.
5) SKILL/SAFETY MODES
Cycle between 3 different skill modes. Each mode has a different top
speed and sensitivity. The mode will only change if you are not using
your H1 scooter.
• Beginner Mode - This mode is recommended for first time Hover-1
scooter users. In this mode, the sensitivity and top speed are very low.
• Intermediate Mode - This mode is recommended for users that are
comfortable using Hover-1 scooters but are not ready for full speed
and extra sensitive controls. In this mode, the sensitivity and top speed
are moderate.
• Expert Mode - This mode is recommended for everyday Hover-1
scooter users. In this mode, the sensitivity and top speed are set to the
maximum setting.
NOTE: Skill and safety mode must be selected. The Hover-1 will default
to “Beginner” mode if another mode is not selected.
6) STANDBY MODE
“Standby Mode” allows you to put your H1 into a low-power standby
state. Your H1 cannot be used while in standby. You must disable
standby mode before you can ride the H1. When in standby mode,
the button will say “Power On”. Press “Power On” to disable the
standby mode.
Please note, if you have your “Auto Shutdown Time” set, your H1 will
turn off completely at the specified time. You will be unable to power
it back on from the App. You will have to physically press the power
button on your H1 to turn it back on.
7) HEADLIGHTS
Press “Headlights” to set a custom color for your H1’s Path Illumination
Lights. Simply choose your desired color from the color wheel. For your
convenience, 4 basic colors have also been set as presets below the
brightness bar.
8) GPS
Press “GPS” to open a navigation screen that pin-points your exact
location. From the moment you press “Start”, it begins recording your
travel route. Once you press “Finish”, your route is saved in the App.
Press the bar icon, in the top right corner of your screen, to view all
saved travel routes.
By selecting one of the saved routes, you can view the details. Press
“...” to share or delete the route.
VEHICLE INFO
10
All manuals and user guides at all-guides.com
all-guides.com

Your H1 is an App-enabled scooter that works with most mobile
devices. You must download the Hover-1 app in order to change
certain features of your H1 such as headlight colors and skill mode.
Please download the App from either the App Store or download
the App from the Google Play Store.
USING THE APP
Launch the app from your device, you will be directed to the intro
page. You may register your H1 by pressing the “Registration”. You
may continue to the dashboard by pressing “Skip”.
Please note, we encourage you to register your H1 scooter. For this
purpose, the intro page will continue to show every time the App is
launched if registration has not been completed. Once registration is
completed, the App will open directly to the dashboard.
1) REGISTRATION
Complete the form by entering your information to register your H1.
Fields marked with a “*” are required fields and the form cannot be
submitted without this information. Once you submit the registration
form, the safety, legal and privacy disclaimers will need to be
reviewed and accepted before moving on to the dashboard. Once
accepted, press “Next.”
2) DASHBOARD
Before allowing you to access the dashboard, a safety screen will
pop-up for 3 seconds. Please review the safety notes in this screen
while the dashboard loads. The dashboard will appear as shown
below.
1. Connect Your H1 - To connect to your H1 through Bluetooth on your
smart phone, press “Connect”. If your H1 is already paired, this part of
the screen will show “Connected” in blue.
2. Settings - Press the gear icon to adjust settings.
3. Speed - The digital speedometer displays your speed in miles per
hour.
4. Change Mode - Change safety/skill levels and H1 sensitivity.
5. Battery - The percentage displays the remaining battery life of your
H1.
6. Standby Mode - Put your H1 into a low-power mode when not in
use.
7. Customize Headlights - Change the colors and brightness of your
Path Illuminating Lights.
8. Vehicle - Displays the name assigned to your H1.
9. Vehicle Info - Swipe up from the bottom of your screen to display
more information about your H1 in real time.
10. GPS Tracking - View GPS & tracking to see where you have ridden
your H1 and display your real time location.
3) CONNECT
Press “Connect” to have the App begin scanning for any Hover-1
devices. Your H1 must be powered on and your smart phone’s
Bluetooth must be enabled. If your Bluetooth is not enabled on your
smart phone, the App will remind you to enable it.
Once scanning is complete, all detected Hover-1 scooters will display
in a list. Press the select button to pair with a scooter and use the PIN
“000000”. If multiple Hover-1 scooters appear, continue attempting to
pair until your H1 is paired.
Once paired, the dashboard will display “Connected” in blue. You
may now begin using the App with your H1.
4) SETTINGS
Press the gear icon to change settings for your H1.
• Change Vehicle’s Name - Customize the name for your H1 here. This
name change will reflect in the dashboard and connect pages.
• Set Auto Shutdown Time - This setting allows you to set a time for your
H1 to shutdown automatically.
• F.A.Q. - Frequently asked questions and answers are shown here
such as basic instructions and troubleshooting.
• Customer Service - View contact information for the Hover-1
customer service team.
• Terms & Conditions - Safety, legal and privacy disclaimers are here
for reference.
• App Version - Display the current App version and check for any
updates.
Hover-1
Scanning...
Hover-1
Select
Select
CONNECT
SETTINGS
• Hardware/Software Version - Display the hardware and software
versions of your H1. These fields will only appear when connected to
your H1 scooter.
• Diagnostics - Run a diagnostic check on your H1 and stay informed
of any hardware, software and electrical issues that may need to be
addressed.
5) SKILL/SAFETY MODES
Cycle between 3 different skill modes. Each mode has a different top
speed and sensitivity. The mode will only change if you are not using
your H1 scooter.
• Beginner Mode - This mode is recommended for first time Hover-1
scooter users. In this mode, the sensitivity and top speed are very low.
• Intermediate Mode - This mode is recommended for users that are
comfortable using Hover-1 scooters but are not ready for full speed
and extra sensitive controls. In this mode, the sensitivity and top speed
are moderate.
• Expert Mode - This mode is recommended for everyday Hover-1
scooter users. In this mode, the sensitivity and top speed are set to the
maximum setting.
NOTE: Skill and safety mode must be selected. The Hover-1 will default
to “Beginner” mode if another mode is not selected.
6) STANDBY MODE
“Standby Mode” allows you to put your H1 into a low-power standby
state. Your H1 cannot be used while in standby. You must disable
standby mode before you can ride the H1. When in standby mode,
the button will say “Power On”. Press “Power On” to disable the
standby mode.
Please note, if you have your “Auto Shutdown Time” set, your H1 will
turn off completely at the specified time. You will be unable to power
it back on from the App. You will have to physically press the power
button on your H1 to turn it back on.
7) HEADLIGHTS
Press “Headlights” to set a custom color for your H1’s Path Illumination
Lights. Simply choose your desired color from the color wheel. For your
convenience, 4 basic colors have also been set as presets below the
brightness bar.
8) GPS
Press “GPS” to open a navigation screen that pin-points your exact
location. From the moment you press “Start”, it begins recording your
travel route. Once you press “Finish”, your route is saved in the App.
Press the bar icon, in the top right corner of your screen, to view all
saved travel routes.
By selecting one of the saved routes, you can view the details. Press
“...” to share or delete the route.
11
All manuals and user guides at all-guides.com

Your H1 is an App-enabled scooter that works with most mobile
devices. You must download the Hover-1 app in order to change
certain features of your H1 such as headlight colors and skill mode.
Please download the App from either the App Store or download
the App from the Google Play Store.
USING THE APP
Launch the app from your device, you will be directed to the intro
page. You may register your H1 by pressing the “Registration”. You
may continue to the dashboard by pressing “Skip”.
Please note, we encourage you to register your H1 scooter. For this
purpose, the intro page will continue to show every time the App is
launched if registration has not been completed. Once registration is
completed, the App will open directly to the dashboard.
1) REGISTRATION
Complete the form by entering your information to register your H1.
Fields marked with a “*” are required fields and the form cannot be
submitted without this information. Once you submit the registration
form, the safety, legal and privacy disclaimers will need to be
reviewed and accepted before moving on to the dashboard. Once
accepted, press “Next.”
2) DASHBOARD
Before allowing you to access the dashboard, a safety screen will
pop-up for 3 seconds. Please review the safety notes in this screen
while the dashboard loads. The dashboard will appear as shown
below.
1. Connect Your H1 - To connect to your H1 through Bluetooth on your
smart phone, press “Connect”. If your H1 is already paired, this part of
the screen will show “Connected” in blue.
2. Settings - Press the gear icon to adjust settings.
3. Speed - The digital speedometer displays your speed in miles per
hour.
4. Change Mode - Change safety/skill levels and H1 sensitivity.
5. Battery - The percentage displays the remaining battery life of your
H1.
6. Standby Mode - Put your H1 into a low-power mode when not in
use.
7. Customize Headlights - Change the colors and brightness of your
Path Illuminating Lights.
8. Vehicle - Displays the name assigned to your H1.
9. Vehicle Info - Swipe up from the bottom of your screen to display
more information about your H1 in real time.
10. GPS Tracking - View GPS & tracking to see where you have ridden
your H1 and display your real time location.
3) CONNECT
Press “Connect” to have the App begin scanning for any Hover-1
devices. Your H1 must be powered on and your smart phone’s
Bluetooth must be enabled. If your Bluetooth is not enabled on your
smart phone, the App will remind you to enable it.
Once scanning is complete, all detected Hover-1 scooters will display
in a list. Press the select button to pair with a scooter and use the PIN
“000000”. If multiple Hover-1 scooters appear, continue attempting to
pair until your H1 is paired.
Once paired, the dashboard will display “Connected” in blue. You
may now begin using the App with your H1.
4) SETTINGS
Press the gear icon to change settings for your H1.
• Change Vehicle’s Name - Customize the name for your H1 here. This
name change will reflect in the dashboard and connect pages.
• Set Auto Shutdown Time - This setting allows you to set a time for your
H1 to shutdown automatically.
• F.A.Q. - Frequently asked questions and answers are shown here
such as basic instructions and troubleshooting.
• Customer Service - View contact information for the Hover-1
customer service team.
• Terms & Conditions - Safety, legal and privacy disclaimers are here
for reference.
• App Version - Display the current App version and check for any
updates.
• Hardware/Software Version - Display the hardware and software
versions of your H1. These fields will only appear when connected to
your H1 scooter.
• Diagnostics - Run a diagnostic check on your H1 and stay informed
of any hardware, software and electrical issues that may need to be
addressed.
5) SKILL/SAFETY MODES
Cycle between 3 different skill modes. Each mode has a different top
speed and sensitivity. The mode will only change if you are not using
your H1 scooter.
• Beginner Mode - This mode is recommended for first time Hover-1
scooter users. In this mode, the sensitivity and top speed are very low.
• Intermediate Mode - This mode is recommended for users that are
comfortable using Hover-1 scooters but are not ready for full speed
and extra sensitive controls. In this mode, the sensitivity and top speed
are moderate.
• Expert Mode - This mode is recommended for everyday Hover-1
scooter users. In this mode, the sensitivity and top speed are set to the
maximum setting.
NOTE: Skill and safety mode must be selected. The Hover-1 will default
to “Beginner” mode if another mode is not selected.
6) STANDBY MODE
“Standby Mode” allows you to put your H1 into a low-power standby
state. Your H1 cannot be used while in standby. You must disable
standby mode before you can ride the H1. When in standby mode,
the button will say “Power On”. Press “Power On” to disable the
standby mode.
Please note, if you have your “Auto Shutdown Time” set, your H1 will
turn off completely at the specified time. You will be unable to power
it back on from the App. You will have to physically press the power
button on your H1 to turn it back on.
7) HEADLIGHTS
Press “Headlights” to set a custom color for your H1’s Path Illumination
Lights. Simply choose your desired color from the color wheel. For your
convenience, 4 basic colors have also been set as presets below the
brightness bar.
8) GPS
Press “GPS” to open a navigation screen that pin-points your exact
location. From the moment you press “Start”, it begins recording your
travel route. Once you press “Finish”, your route is saved in the App.
Press the bar icon, in the top right corner of your screen, to view all
saved travel routes.
By selecting one of the saved routes, you can view the details. Press
“...” to share or delete the route.
Mode: Beginner
Mode: Intermediate Mode: Expert
Standby Mode Power On
12
All manuals and user guides at all-guides.com

Your H1 is an App-enabled scooter that works with most mobile
devices. You must download the Hover-1 app in order to change
certain features of your H1 such as headlight colors and skill mode.
Please download the App from either the App Store or download
the App from the Google Play Store.
USING THE APP
Launch the app from your device, you will be directed to the intro
page. You may register your H1 by pressing the “Registration”. You
may continue to the dashboard by pressing “Skip”.
Please note, we encourage you to register your H1 scooter. For this
purpose, the intro page will continue to show every time the App is
launched if registration has not been completed. Once registration is
completed, the App will open directly to the dashboard.
1) REGISTRATION
Complete the form by entering your information to register your H1.
Fields marked with a “*” are required fields and the form cannot be
submitted without this information. Once you submit the registration
form, the safety, legal and privacy disclaimers will need to be
reviewed and accepted before moving on to the dashboard. Once
accepted, press “Next.”
2) DASHBOARD
Before allowing you to access the dashboard, a safety screen will
pop-up for 3 seconds. Please review the safety notes in this screen
while the dashboard loads. The dashboard will appear as shown
below.
1. Connect Your H1 - To connect to your H1 through Bluetooth on your
smart phone, press “Connect”. If your H1 is already paired, this part of
the screen will show “Connected” in blue.
2. Settings - Press the gear icon to adjust settings.
3. Speed - The digital speedometer displays your speed in miles per
hour.
4. Change Mode - Change safety/skill levels and H1 sensitivity.
5. Battery - The percentage displays the remaining battery life of your
H1.
6. Standby Mode - Put your H1 into a low-power mode when not in
use.
7. Customize Headlights - Change the colors and brightness of your
Path Illuminating Lights.
8. Vehicle - Displays the name assigned to your H1.
9. Vehicle Info - Swipe up from the bottom of your screen to display
more information about your H1 in real time.
10. GPS Tracking - View GPS & tracking to see where you have ridden
your H1 and display your real time location.
3) CONNECT
Press “Connect” to have the App begin scanning for any Hover-1
devices. Your H1 must be powered on and your smart phone’s
Bluetooth must be enabled. If your Bluetooth is not enabled on your
smart phone, the App will remind you to enable it.
Once scanning is complete, all detected Hover-1 scooters will display
in a list. Press the select button to pair with a scooter and use the PIN
“000000”. If multiple Hover-1 scooters appear, continue attempting to
pair until your H1 is paired.
Once paired, the dashboard will display “Connected” in blue. You
may now begin using the App with your H1.
4) SETTINGS
Press the gear icon to change settings for your H1.
• Change Vehicle’s Name - Customize the name for your H1 here. This
name change will reflect in the dashboard and connect pages.
• Set Auto Shutdown Time - This setting allows you to set a time for your
H1 to shutdown automatically.
• F.A.Q. - Frequently asked questions and answers are shown here
such as basic instructions and troubleshooting.
• Customer Service - View contact information for the Hover-1
customer service team.
• Terms & Conditions - Safety, legal and privacy disclaimers are here
for reference.
• App Version - Display the current App version and check for any
updates.
GPS TRACKING
• Hardware/Software Version - Display the hardware and software
versions of your H1. These fields will only appear when connected to
your H1 scooter.
• Diagnostics - Run a diagnostic check on your H1 and stay informed
of any hardware, software and electrical issues that may need to be
addressed.
5) SKILL/SAFETY MODES
Cycle between 3 different skill modes. Each mode has a different top
speed and sensitivity. The mode will only change if you are not using
your H1 scooter.
• Beginner Mode - This mode is recommended for first time Hover-1
scooter users. In this mode, the sensitivity and top speed are very low.
• Intermediate Mode - This mode is recommended for users that are
comfortable using Hover-1 scooters but are not ready for full speed
and extra sensitive controls. In this mode, the sensitivity and top speed
are moderate.
• Expert Mode - This mode is recommended for everyday Hover-1
scooter users. In this mode, the sensitivity and top speed are set to the
maximum setting.
NOTE: Skill and safety mode must be selected. The Hover-1 will default
to “Beginner” mode if another mode is not selected.
6) STANDBY MODE
“Standby Mode” allows you to put your H1 into a low-power standby
state. Your H1 cannot be used while in standby. You must disable
standby mode before you can ride the H1. When in standby mode,
the button will say “Power On”. Press “Power On” to disable the
standby mode.
Please note, if you have your “Auto Shutdown Time” set, your H1 will
turn off completely at the specified time. You will be unable to power
it back on from the App. You will have to physically press the power
button on your H1 to turn it back on.
7) HEADLIGHTS
Press “Headlights” to set a custom color for your H1’s Path Illumination
Lights. Simply choose your desired color from the color wheel. For your
convenience, 4 basic colors have also been set as presets below the
brightness bar.
8) GPS
Press “GPS” to open a navigation screen that pin-points your exact
location. From the moment you press “Start”, it begins recording your
travel route. Once you press “Finish”, your route is saved in the App.
Press the bar icon, in the top right corner of your screen, to view all
saved travel routes.
By selecting one of the saved routes, you can view the details. Press
“...” to share or delete the route.
HEADLIGHTS
Presets
Headlights
Power
13
All manuals and user guides at all-guides.com

The H1 has a powerful built-in wireless speakers so you can play your
music while riding.
PAIRING THE SPEAKER
1. Ensure your H1 is turned off. If it is not, please turn off your Hover-1 first
before pairing.
2. Turn on your H1 and the speakers will announce that it’s waiting for
a Bluetooth®connection. This will indicate your H1 speaker is now in
pairing mode.
3. Place the H1 and the Bluetooth®device to which you would like to
pair it within the operating distance. We recommend keeping the two
devices no further than 3 feet apart during pairing.
4. Ensure Bluetooth®is enabled on your phone or music device. Refer
to manufacturer’s instructions for how to enable Bluetooth®on your
device.
5. Once you have activated Bluetooth®on your device, select the
option “HY-H1” from the list of available Bluetooth®devices.
6. If required, enter the PIN code "000000" and confirm the entry.
7. Please note, pairing mode on the Hover-1 will last for two minutes. If
no devices are paired after two minutes, the H1 speaker will
automatically return to standby mode.
8. If pairing is unsuccessful, turn off the H1 first and re-pair following the
aforementioned steps.
NOTE: Once you have paired the H1 speaker with a device, the
speaker will remember this device and will pair automatically when
the device’s Bluetooth®is activated and in range. You do not need to
re-pair any previously connected devices.
Your H1 can pair up to two multi-point devices. You can reconnect a
previously paired device without going through the pairing or PIN
process on up to two devices.
LISTENING TO MUSIC
Once the H1 Bluetooth speaker is paired to your device, you can
stream music wirelessly through it. Only one speaker will play music as
the other speaker is strictly for safety alerts from your Hover-1. Select
the track you wish to listen to on your device to listen via the speakers.
All volume and track controls will be made using your music device.
Should you encounter any problems while streaming, please refer to
your device’s user manual.
BLUETOOTH SPEAKER
14
All manuals and user guides at all-guides.com

Ideal for both indoor and outdoor use, the H1 scooter features a
water-resistant, weatherized case that protects its components from
splashing water. This ensures that the high-quality tech within the H1 is
protected while riding around outdoors & indoors and getting caught
in the rain.
NOTE: The H1 scooter should not be subject to prolonged exposure to
water or submerged. Doing so will damage your H1 scooter and
invalidate the manufacturer’s warranty.
It is important that you fully understand all elements of your H1
scooter. If these elements are not used correctly, you will not have full
control of your H1. Before you ride, or ride outside of a controlled
environment, learn the functions of the various mechanisms on your
scooter.
Practice using these elements of your H1 at slower speeds in a flat,
open area before taking the device out in public areas.
PRE-RIDE CHECKLIST
Ensure that your H1 scooter is in proper working order each and every
time you ride. If a part of the scooter does not function correctly,
please contact our Customer Support Center.
• Ensure the battery is fully charged before riding your scooter.
• If the H1 is not to be used for an extended period of time, please
recharge the battery every 2 months to maintain the battery life.
• Ensure that the screws on the front and back tires are locked firmly
before each ride.
The H1 has a powerful built-in wireless speakers so you can play your
music while riding.
PAIRING THE SPEAKER
1. Ensure your H1 is turned off. If it is not, please turn off your Hover-1 first
before pairing.
2. Turn on your H1 and the speakers will announce that it’s waiting for
a Bluetooth®connection. This will indicate your H1 speaker is now in
pairing mode.
3. Place the H1 and the Bluetooth®device to which you would like to
pair it within the operating distance. We recommend keeping the two
devices no further than 3 feet apart during pairing.
4. Ensure Bluetooth®is enabled on your phone or music device. Refer
to manufacturer’s instructions for how to enable Bluetooth®on your
device.
5. Once you have activated Bluetooth®on your device, select the
option “HY-H1” from the list of available Bluetooth®devices.
6. If required, enter the PIN code "000000" and confirm the entry.
7. Please note, pairing mode on the Hover-1 will last for two minutes. If
no devices are paired after two minutes, the H1 speaker will
automatically return to standby mode.
8. If pairing is unsuccessful, turn off the H1 first and re-pair following the
aforementioned steps.
NOTE: Once you have paired the H1 speaker with a device, the
speaker will remember this device and will pair automatically when
the device’s Bluetooth®is activated and in range. You do not need to
re-pair any previously connected devices.
Your H1 can pair up to two multi-point devices. You can reconnect a
previously paired device without going through the pairing or PIN
process on up to two devices.
LISTENING TO MUSIC
Once the H1 Bluetooth speaker is paired to your device, you can
stream music wirelessly through it. Only one speaker will play music as
the other speaker is strictly for safety alerts from your Hover-1. Select
the track you wish to listen to on your device to listen via the speakers.
All volume and track controls will be made using your music device.
Should you encounter any problems while streaming, please refer to
your device’s user manual.
IPX4 WATER RESISTANCE
BEFORE RIDING
WARNING
Any H1 that does not work properly can
cause you to lose control and fall. Do
not ride an H1 scooter with a part that
is damaged; replace the damaged
part before riding.
15
All manuals and user guides at all-guides.com
all-guides.com

The H1 has a powerful built-in wireless speakers so you can play your
music while riding.
PAIRING THE SPEAKER
1. Ensure your H1 is turned off. If it is not, please turn off your Hover-1 first
before pairing.
2. Turn on your H1 and the speakers will announce that it’s waiting for
a Bluetooth®connection. This will indicate your H1 speaker is now in
pairing mode.
3. Place the H1 and the Bluetooth®device to which you would like to
pair it within the operating distance. We recommend keeping the two
devices no further than 3 feet apart during pairing.
4. Ensure Bluetooth®is enabled on your phone or music device. Refer
to manufacturer’s instructions for how to enable Bluetooth®on your
device.
5. Once you have activated Bluetooth®on your device, select the
option “HY-H1” from the list of available Bluetooth®devices.
6. If required, enter the PIN code "000000" and confirm the entry.
7. Please note, pairing mode on the Hover-1 will last for two minutes. If
no devices are paired after two minutes, the H1 speaker will
automatically return to standby mode.
8. If pairing is unsuccessful, turn off the H1 first and re-pair following the
aforementioned steps.
NOTE: Once you have paired the H1 speaker with a device, the
speaker will remember this device and will pair automatically when
the device’s Bluetooth®is activated and in range. You do not need to
re-pair any previously connected devices.
Your H1 can pair up to two multi-point devices. You can reconnect a
previously paired device without going through the pairing or PIN
process on up to two devices.
LISTENING TO MUSIC
Once the H1 Bluetooth speaker is paired to your device, you can
stream music wirelessly through it. Only one speaker will play music as
the other speaker is strictly for safety alerts from your Hover-1. Select
the track you wish to listen to on your device to listen via the speakers.
All volume and track controls will be made using your music device.
Should you encounter any problems while streaming, please refer to
your device’s user manual.
• Please wear all appropriate safety and protective gear as
previously mentioned in the User Manual before operating your
device.
• Make sure to wear comfortable clothes and flat closed-toe shoes
when operating your device.
• Please carefully read the User Manual, which will assist in explaining
the basic working principles and provide tips on how to best enjoy
your experience.
The first rule in safe riding is to use common sense. A scooter is
vulnerable; it cannot protect you in a crash, against impact, or loss of
control the way driving a car can. It does not have bumpers or
airbags as a car does. This section is a guide of safe riding practices
for on and off-road operation. Make sure you are using your H1
scooter properly.
Different localities and countries have different laws governing riding
on public roads, and you should check with local officials to ensure
you are complying with these laws.
Hover-1 is not liable for tickets or violations given to riders who do not
follow these regulations.
• For your safety, always wear a helmet that meets CPSC or CE safety
standards. In the event of an accident, a helmet can protect you
from serious injury and in some cases, even death.
• Obey all local traffic laws. Obey red and green lights, one-way
streets, stop signs, pedestrian crosswalks, etc.
• Ride with the traffic, not against it.
• Ride defensively; expect the unexpected.
• Give pedestrians the right-of-way.
• Do not ride too close to pedestrians and alert them if you intend to
pass them from behind.
SAFETY PRECAUTIONS
16
All manuals and user guides at all-guides.com

The H1 has a powerful built-in wireless speakers so you can play your
music while riding.
PAIRING THE SPEAKER
1. Ensure your H1 is turned off. If it is not, please turn off your Hover-1 first
before pairing.
2. Turn on your H1 and the speakers will announce that it’s waiting for
a Bluetooth®connection. This will indicate your H1 speaker is now in
pairing mode.
3. Place the H1 and the Bluetooth®device to which you would like to
pair it within the operating distance. We recommend keeping the two
devices no further than 3 feet apart during pairing.
4. Ensure Bluetooth®is enabled on your phone or music device. Refer
to manufacturer’s instructions for how to enable Bluetooth®on your
device.
5. Once you have activated Bluetooth®on your device, select the
option “HY-H1” from the list of available Bluetooth®devices.
6. If required, enter the PIN code "000000" and confirm the entry.
7. Please note, pairing mode on the Hover-1 will last for two minutes. If
no devices are paired after two minutes, the H1 speaker will
automatically return to standby mode.
8. If pairing is unsuccessful, turn off the H1 first and re-pair following the
aforementioned steps.
NOTE: Once you have paired the H1 speaker with a device, the
speaker will remember this device and will pair automatically when
the device’s Bluetooth®is activated and in range. You do not need to
re-pair any previously connected devices.
Your H1 can pair up to two multi-point devices. You can reconnect a
previously paired device without going through the pairing or PIN
process on up to two devices.
LISTENING TO MUSIC
Once the H1 Bluetooth speaker is paired to your device, you can
stream music wirelessly through it. Only one speaker will play music as
the other speaker is strictly for safety alerts from your Hover-1. Select
the track you wish to listen to on your device to listen via the speakers.
All volume and track controls will be made using your music device.
Should you encounter any problems while streaming, please refer to
your device’s user manual.
WARNING
When you ride in low-visibility conditions
such as fog, dusk, or night, you might be
diicult to see, which could lead to a
collision. In addition to keeping your
headlight on, wear bright, reective
clothing when riding in poor lighting
conditions.
• Slow down at all street intersections and look to the left and right
before crossing.
Your Hover-1 is not equipped with reflectors. It is not recommended
that you ride your bike in conditions of low visibility.
If you are riding your scooter in low-visibility conditions, ensure your
LED lights are turned on, and that you are wearing bright, reflective
clothing.
Think about safety when you ride. You can prevent many accidents if
you think about safety. Below is a helpful checklist for Compact riders.
SAFETY CHECKLIST
• Do not ride “double” with more than one rider on the scooter.
• Avoid riding in large groups, as this can force you to ride too close
to other riders, making it difficult to see other vehicles and road
hazards.
• Do not ride above your skill level. Ensure you have had enough
practice with all functions and features of your Hover-1.
• Do not ride too fast -- with increased speed comes increased risk. If
you are moving at a higher speed, small bumps can turn into large
impacts, leading to a higher risk of injury if an accident occurs.
• Do not ride your scooter with any pets.
17
All manuals and user guides at all-guides.com

The H1 has a powerful built-in wireless speakers so you can play your
music while riding.
PAIRING THE SPEAKER
1. Ensure your H1 is turned off. If it is not, please turn off your Hover-1 first
before pairing.
2. Turn on your H1 and the speakers will announce that it’s waiting for
a Bluetooth®connection. This will indicate your H1 speaker is now in
pairing mode.
3. Place the H1 and the Bluetooth®device to which you would like to
pair it within the operating distance. We recommend keeping the two
devices no further than 3 feet apart during pairing.
4. Ensure Bluetooth®is enabled on your phone or music device. Refer
to manufacturer’s instructions for how to enable Bluetooth®on your
device.
5. Once you have activated Bluetooth®on your device, select the
option “HY-H1” from the list of available Bluetooth®devices.
6. If required, enter the PIN code "000000" and confirm the entry.
7. Please note, pairing mode on the Hover-1 will last for two minutes. If
no devices are paired after two minutes, the H1 speaker will
automatically return to standby mode.
8. If pairing is unsuccessful, turn off the H1 first and re-pair following the
aforementioned steps.
NOTE: Once you have paired the H1 speaker with a device, the
speaker will remember this device and will pair automatically when
the device’s Bluetooth®is activated and in range. You do not need to
re-pair any previously connected devices.
Your H1 can pair up to two multi-point devices. You can reconnect a
previously paired device without going through the pairing or PIN
process on up to two devices.
LISTENING TO MUSIC
Once the H1 Bluetooth speaker is paired to your device, you can
stream music wirelessly through it. Only one speaker will play music as
the other speaker is strictly for safety alerts from your Hover-1. Select
the track you wish to listen to on your device to listen via the speakers.
All volume and track controls will be made using your music device.
Should you encounter any problems while streaming, please refer to
your device’s user manual.
• Slow down at all street intersections and look to the left and right
before crossing.
Your Hover-1 is not equipped with reflectors. It is not recommended
that you ride your bike in conditions of low visibility.
If you are riding your scooter in low-visibility conditions, ensure your
LED lights are turned on, and that you are wearing bright, reflective
clothing.
Think about safety when you ride. You can prevent many accidents if
you think about safety. Below is a helpful checklist for Compact riders.
SAFETY CHECKLIST
• Do not ride “double” with more than one rider on the scooter.
• Avoid riding in large groups, as this can force you to ride too close
to other riders, making it difficult to see other vehicles and road
hazards.
• Do not ride above your skill level. Ensure you have had enough
practice with all functions and features of your Hover-1.
• Do not ride too fast -- with increased speed comes increased risk. If
you are moving at a higher speed, small bumps can turn into large
impacts, leading to a higher risk of injury if an accident occurs.
• Do not ride your scooter with any pets.
• Before stepping on your device, make sure it is placed flat on level
ground, the power is on, and the Running Indicator light is green. Do
not step on if the Running Indicator is red.
• Do not try to open or modify your device, as doing so, voids the
manufacturer warranty, and may cause failure to your device
leading to serious bodily injury or death.
• Do not use the device to place yourself or anyone else and their
property in danger.
• If you and your friend(s) are riding H1 scooters together, be sure to
keep a safe distance between each other to prevent collisions,
property damage, serious injuries or even death.
• Be sure to keep you feet on the pedals at all times. Moving your
feet off your device while driving is dangerous.
• Do not operate the device while under the influence of drugs
and/or alcohol.
• Do not operate the device when you are restless or sleepy.
• Use your best judgment to keep yourself out of dangerous situations
with your device.
• Do not ride your device off of curbs, ramps, or attempt to operate
in a skate park, empty pool, or in any way similar to a skateboard or
scooter. The H1 IS NOT A SKATEBOARD.
• Do not continuously spin in place, it will cause dizziness and
increases risk of injury.
• Do not abuse your device, doing so can damage your unit and
cause failure to the operating system leading to injury.
• Do not ride in or near puddles of water, mud, sand, stones, gravel,
debris or near rough and rugged terrain.
• The device can be used on paved roads that are flat and even. If
you encounter uneven pavement, please lift your Hover-1 over and
past the obstruction.
• Do not ride in inclement weather: snow, rain, hail, sleek, on icy roads
or in extreme heat.
18
All manuals and user guides at all-guides.com

The H1 has a powerful built-in wireless speakers so you can play your
music while riding.
PAIRING THE SPEAKER
1. Ensure your H1 is turned off. If it is not, please turn off your Hover-1 first
before pairing.
2. Turn on your H1 and the speakers will announce that it’s waiting for
a Bluetooth®connection. This will indicate your H1 speaker is now in
pairing mode.
3. Place the H1 and the Bluetooth®device to which you would like to
pair it within the operating distance. We recommend keeping the two
devices no further than 3 feet apart during pairing.
4. Ensure Bluetooth®is enabled on your phone or music device. Refer
to manufacturer’s instructions for how to enable Bluetooth®on your
device.
5. Once you have activated Bluetooth®on your device, select the
option “HY-H1” from the list of available Bluetooth®devices.
6. If required, enter the PIN code "000000" and confirm the entry.
7. Please note, pairing mode on the Hover-1 will last for two minutes. If
no devices are paired after two minutes, the H1 speaker will
automatically return to standby mode.
8. If pairing is unsuccessful, turn off the H1 first and re-pair following the
aforementioned steps.
NOTE: Once you have paired the H1 speaker with a device, the
speaker will remember this device and will pair automatically when
the device’s Bluetooth®is activated and in range. You do not need to
re-pair any previously connected devices.
Your H1 can pair up to two multi-point devices. You can reconnect a
previously paired device without going through the pairing or PIN
process on up to two devices.
LISTENING TO MUSIC
Once the H1 Bluetooth speaker is paired to your device, you can
stream music wirelessly through it. Only one speaker will play music as
the other speaker is strictly for safety alerts from your Hover-1. Select
the track you wish to listen to on your device to listen via the speakers.
All volume and track controls will be made using your music device.
Should you encounter any problems while streaming, please refer to
your device’s user manual.
• Do not ride in or near pools or other large bodies of water.
• Bend your knees when riding on bumpy or uneven pavement to
absorb the shock and vibration and help you keep your balance.
• If you are unsure if you can safely ride on a specific terrain, step off
and carry your device. ALWAYS BE ON THE SIDE OF CAUTION.
• Do not attempt to ride over bumps or objects greater then ½ inch
even when prepared and bending your knees.
• PAY ATTENTION - look at where you are riding and be conscious
of the road conditions, people, places, property and objects
around you.
• Do not operate the device in crowded areas.
• Operate your device with extreme caution when indoors,
especially around people, property, and narrow spaces.
• Do not operate the device while talking, texting, or looking at
your phone.
• Do not ride your device where it is not permitted.
• Do not ride your device near motor vehicles or on public roads.
• Do not climb or travel down steep hills or up steep hills with
your device.
• The device is intended for use by a single individual, DO NOT
attempt to operate the device with two or more people.
• Do not carry anything while riding the device.
• Individuals with lack of balance should not attempt to operate
the device.
• Pregnant women should not operate the device.
• Young children and the elderly should not operate the device
without proper instruction and supervision.
• At higher speeds, always take into consideration longer
stopping distances.
19
All manuals and user guides at all-guides.com