HP Pavilion 8800 - Desktop PC User manual

HP 8800 Routers
FIPS Enclosure Installation Guide
P
art number: 5998-3449
Document version: 6P101-20120928
5998-3449

Legal and notice information
© Copyright 2012 Hewlett-Packard Development Company, L.P.
No part of this documentation may be reproduced or transmitted in
any form or by any means without prior written consent of
Hewlett-Packard Development Company, L.P.
The information contained herein is subject to change without notice.
HEWLETT-PACKARD COMPANY MAKES NO WARRANTY OF ANY
KIND WITH REGARD TO THIS MATERIAL, INCLUDING, BUT NOT
LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND
FITNESS FOR A PARTICULAR PURPOSE. Hewlett-Packard shall not be
liable for errors contained herein or for incidental or consequential
damages in connection with the furnishing, performance, or use of this
material.
The only warranties for HP products and services are set forth in the
express warranty statements accompanying such products and services.
Nothing herein should be construed as constituting an additional
warranty. HP shall not be liable for technical or editorial errors or
omissions contained herein.

Manual Version: 6P101-20120928
BOM: 3104A0C3
Part number: 5998-3449
Contents
HP A8800 routers FIPS kit installation guide ··················································1
Installing the FIPS enclosure ············································································ 1
Introduction to the FIPS enclosure·························································· 1
Installation tools and accessories ·························································· 3
Preparing for installation ········································································ 3
Installing the FIPS enclosure to the A8805/A8812···························· 4
Installing the FIPS enclosure to the A8808-V ······································· 8
Applying tamper evidence labels·································································11
i

Manual Version: 6P101-20120928
BOM: 3104A0C3
Part number: 5998-3449
HP A8800 routers FIPS kit installation
guide
WARNING
!
T
o avoid bodily injury and damage to the router components, turn off the
power supply of the router before you install the FIPS kit.
HP A8800 routers meet the requirements of the FIPS security level 2.
NOTE:
•
The installation procedure must be performed by qualified personnel.
•
Before installation, read Compliance and Safety Manual for the
compatible router of the FIPS enclosure.
Installing the FIPS enclosure
The installation procedures vary with the installation environment.
Introduction to the FIPS enclosure
IMPORTANT:
Only use the screws and hex bolts that are supplied in the FIPS
enclosure
to secure the opacity shields.
The FIPS enclosure for an HP A8805 or A8812 router has the
following components:
1

Manual Version: 6P101-20120928
BOM: 3104A0C3
Part number: 5998-3449
Product
Code Description Component
Installation
/adhesive
position
Quantity
•JG570A
(for an HP
A8805
router)
•JG572A
(for an HP
A8812
router)
Left-side
opacity
shield
assembly
•1 × opacity
shield
•2 × guide
rail
•6 × M3
countersunk-
head screw
Left 1
Right-side
opacity
shield
assembly
•1 × opacity
shield
•1 × upper
mounting
plate
•1 × lower
mounting
plate
•2 × M3
pan-head
screw
Right 1
Rear
opacity
shield
assembly
•1 × opacity
shield
•4 × hex bolt
•4 × M3
countersunk-
head screw
Rear 1
The FIPS enclosure for an HP A8808-V router has the following
components:
2

Manual Version: 6P101-20120928
BOM: 3104A0C3
Part number: 5998-3449
Product
Code Description Component
Installation
/adhesive
position
Quantity
JG571A
Top opacity
shield
assembly
•3 × opacity
shield
•3 × mounting
plate
•9 × M3
pan-head
screw
Top 1
Front opacity
shield
assembly
1 × opacity shield Front 1
Rear opacity
shield
assembly
1 × opacity shield Rear 1
Installation tools and accessories
Preparing for installation
•
Make sure the operating temperature is not higher than 40°C (104°F).
M3 pan-head screw
(supplied with the
FIPS enclosure)
Hex bolt
(supplied with the
FIPS enclosure)
Phillips screwdriver
(user-supplied) Diagonal pliers
(user-supplied)Needle-nose
pliers (user-
supplied)
Alcohol-based
cleaning pad
(user-supplied)
ESD-preventive
wrist strap (supplied
with the router)
M3 countersunk-
head screw
(supplied with the
FIPS enclosure)
3

Manual Version: 6P101-20120928
BOM: 3104A0C3
Part number: 5998-3449
•
Ensure enough clearance for installation.
•
Face the front of the chassis to locate the installation positions (left and
right).
•
Wear an ESD-preventive wrist strap and make sure it is well grounded.
•
If the router has been mounted on a rack, remove it from the rack.
Installing the FIPS enclosure to the
A8805/A8812
The installation procedures are the same for HP A8805 and A8812
routers. This example installs a FIPS enclosure for an HP A8805 router.
To install the FIPS enclosure to the A8805:
1. Unpack the left-side opacity shield assembly and take out one guide
rail.
2. Position the guide rail to align its three countersunk holes with the
unused screw holes on the top left side of the chassis, and secure the
guide rail to the chassis with M3 countersunk-head screws.
3. Mount the other guide rail to the bottom left side of the chassis in the
same way.
4

Manual Version: 6P101-20120928
BOM: 3104A0C3
Part number: 5998-3449
Figure 1 Mounting guide rails to the left side of the chassis
4. Slowly push the left-side opacity shield along the guide rails until it
stops and fasten the two captive screws.
5

Manual Version: 6P101-20120928
BOM: 3104A0C3
Part number: 5998-3449
Figure 2 Installing the left-side opacity shield
5. Clean the adhesive area on the top surface of the chassis with
alcohol-based cleaning pads.
6. Unpack the right-side opacity shield assembly and take out the upper
mounting plate.
7. Position the upper mounting plate to the adhesive area on the top right
of the chassis, and press down firmly on the mounting plate to ensure
its solid contact with the adhesive area.
8. Hang the right-side opacity shield to the upper mounting plate and
secure the shield to the chassis with M3 pan-head screws.
9. Install the lower mounting plate in the same way as described in step
7.
Keep the mounting plates dwell 24 hours.
1
2
2
6

Manual Version: 6P101-20120928
BOM: 3104A0C3
Part number: 5998-3449
Figure 3 Installing the right-side opacity shield assembly
10. Unpack the rear opacity shield assembly and take out hex bolts.
11. Completely loosen the M3 countersunk-head screws on the rear side of
the chassis, and install hex bolts in proper holes.
12. Align the holes on the opacity shield with the holes of the hex bolts,
press the opacity shield against the rear panel, and use M3
1
2
3
7