HPRT TP806L User manual
Quick Start Guide
TP806L
Packing List
Power Cord
Printer
Front View
Appearance and components
Power
Error
Paper
Feed
Power LED
Error LED
Paper Status LED
Printer Cover
LED Control Panel
3. Pull out some paper, and close the printer cover.
Paper Loading
Standard Accessories
Xiamen Hanin Electronic Technology Co.,Ltd
TEL:
WEB:
+86-(0)592-5885991
www.hprt.com
Power Adapter
CD Quick Start Guide
Roll Paper
！Notes:
1. The items in the package depend on the actual order.
Tear Bar
To indicate that the marked item
contains sharp edges and should
Rear View Inside View
Power Switch
Paper Guide
Cash Drawer
USB
RS232
Ethernet
InterfacePower Supply
1. Make sure the printer is “OFF”.
2. Connect power adapter with printer.
3. Connect power adapter with power cord.
.
1
2
Power Adapter
3
Power Cord
4
Note:
Cau�on:
This is a Class A product. In a domes�c environment this product may cause
radio interference in which the user may be required to take adequate measures.
！
FCC WARNING
This device complies with part 15 of the FCC Rules. Opera�on
is subject to the following two condi�ons: (1) this device may
not cause harmful interference, and (2) this device must
accept any interference received, including interference that
may cause undesired opera�on.
Any changes or modifica�ons not expressly approved by the
party responsible for compliance could void the user's
authority to operate the equipment.
NOTE: This equipment has been tested and found to comply
with the limits for a Class A digital device, pursuant to part 15
of the FCC Rules. These limits are designed to provide
reasonable protec�on against harmful interference when the
equipment is operated in a commercial environment. This
equipment generates, uses, and can radiate radio frequency
energy and, if not installed and used in accordance with the
instruc�on manual, may cause harmful interference to radio
communica�ons. Opera�on of this equipment in a residen�al
area is likely to cause harmful interference in which case the
user will be required to correct the interference at his own
expense.
-- Reorient or relocate the receiving antenna.
-- Increase the separa�on between the equipment and receiver.
-- Connect the equipment into an outlet on a circuit different
from that to which the receiver is connected.
-- Consult the dealer or an experienced radio/TV technician for
help.
To maintain compliance with FCC’s RF Exposure guidelines,
This equipment should be installed and operated with
minimum distance between 20cm the radiator your body:
Use only the supplied antenna.
CE DECLARATION OF CONFORMITY
Manufacturer cer�fies that the following designated product:
HPRT TP806L
Type of product:
Direct Thermal Line Prin�ng
It is in conformity with the standards.
Under the Council Direc�ve: (LVD) Direc�ve 2014/35/EU rela�ng to
electrical equipment designed for use within Low Voltage Direc�ve.
EN 62368-1:2014+A11:2017
Under the Council Direc�ve: (EMC) Direc�ve 2014/30/EU rela�ng to
Electro Magne�c Compa�bility.
EN 55032: 2015+AC:2016
EN 55035: 2017
EN 61000-3-2: 2014
EN 61000-3-3: 2013
We declare herewith that as a result of the manner in which the
device designated above was designed, the type of construc�on and
the devices which, as a result have been brought on to the general
market comply with the relevant fundamental regula�ons of the CE
Rules for Safety. And we declare herewith the above men�oned
model is conformity with Direc�ve 2014/30/EU and 2014/35/EU.
In the event of any altera�on which has not been approved by us
being made to any device as designated above, this statement shall
thereby be made invalid.
The declara�on is sole responsibility of the manufacturer HPRT.
Test Standard Informa�on
Other manuals for TP806L
1
Other HPRT Printer manuals
