Huawei ATOM GPS User manual

HUAWEI TECHNOLOGIES CO., LTD.
ATOM GPS (Outdoor NE05E and AE 905S)
Quick Installation Guide
Issue: 01
Date: 2016-06-30

Copyright © Huawei Technologies Co., Ltd. 2016. All rights reserved.
No part of this document may be reproduced or transmitted in any form or by any means without prior
written consent of Huawei Technologies Co., Ltd.
Trademarks and Permissions
and other Huawei trademarks are trademarks of Huawei Technologies Co., Ltd.
All other trademarks and trade names mentioned in this document are the property of their respective
holders.
Notice
The purchased products, services and features are stipulated by the contract made between Huawei and
the customer. All or part of the products, services and features described in this document may not be
within the purchase scope or the usage scope. Unless otherwise specified in the contract, all statements,
information, and recommendations in this document are provided "AS IS" without warranties, guarantees or
representations of any kind, either express or implied.
The information in this document is subject to change without notice. Every effort has been made in the
preparation of this document to ensure accuracy of the contents, but all statements, information, and
recommendations in this document do not constitute a warranty of any kind, express or implied.
Huawei Technologies Co., Ltd.
Address:
Huawei Industrial Base
Bantian, Longgang
Shenzhen 518129
People's Republic of China
Website:
http://www.huawei.com
Email:
[email protected]

Installation Flow
PrecautionsPage 1
Cables and ToolsPage 2
Introduction to the ATOM
GPS
Pages
3-4
Installing the NE05E
Pages
9-11
Perform power-on check
and complete the
installation
Pages
13-14
Appendixes
End
Start
Preparation
for
installation
Installing the Power
Terminal to be
Connected to the
NE05E
Page 7
Pages
15-16
Installation Pre-
processing
Pages
7-8
Connecting and Routing
Cables
Page 12
Scenario II: Mounting the
NE05E on a Wall
Pages
10-11
Scenario I: Mounting the
NE05E on a Pole
Pages
9-10
Install the mounting
bracket on the back of
the NE05E
Page 8
Assembling OT
Terminals
Page 15
Installing the GPS
Satellite Antenna System
Pages
4-6
Scenario II: Separated
Installation Scenario
Pages
5-6
Scenario I: Integrated
Installation Scenario
Page 4
Requirements for GPS
Antenna Installation
Positions
Page 16
0

1
Precautions
•This document aims to provide simple and distinctive guidelines for hardware installation.
•This document does not describe operations for the pre-delivery installation. Instead, this document
describers only the operations for on-site installation.
•This document describes how to connect the ATOM GPS to the GPS Satellite Antenna System. The ATOM
GPS consists of the outdoor NE05E and AE 905S. NE05E-SJ is used as examples in this document.
•EHS requirements: The installation personnel should wear safety belts, helmets, shoes, and gloves for
climb operations.
•When installing or maintaining fibers, do not look into the optical port without eye protection. The infrared
laser emitted by the optical interfaces can cause permanent eye damage.
•Exercise caution when touching the device with the high temperature identification to avoid scalding.
Use cables delivered with Huawei devices or cables complying with Huawei standards.
NOTE
NOTE

2
Cables and Tools
Power cable Fiber Shielded network cable
Diagonal pliers Wire stripper Ratchet crimp tool
Hex key
Paper knife
Multimeter Optical power meter Ladder or ladder truck
PGND cable
Adjustable Wrench
(used in wall-
mounting scenarios)
Level
(used in wall-
mounting scenarios)
Claw hammer
(used in wall-
mounting scenarios)
Hammer drill
(used in wall-
mounting scenarios)
Flathead Screwdriver
(M2-M6) Flathead Screwdriver
(M2-M6)
Marker
(used in
wall-mounting scenarios)

3
3
Introduction to the ATN ATOM GPS
FE/GE4 and FE/GE5 are Combo interfaces and either of
them includes one SFP interface and one electrical
interface. The SFP and electrical interfaces cannot be
used at the same time.
a NE05E-SJ
AE 905S
b
Power supply
interface NM interface
(Console interface)
Optical interface Electrical interface
NOTE
NOTE
Before inserting an AE 905S to an optical interface, lock the ejector lever. Before
removing an AE 905S from an optical interface, loosen the ejector lever.
An AE 905S module can be installed in any GE optical interface. Installing an AE
905S module on an FE/GE2 interface is recommended to reduce reliability risks
caused by cable bending.
Lock the ejector lever.
Loosen the ejector lever.

4
Installing the GPS Satellite Antenna System
Install the GPS antenna on the GPS antenna
support, and use four screws to secure it. Install the GPS antenna support on the ground
bar on the right of the device, and use two
screws to secure it.
Remove the rubber plug, and connect the
GPS feeder to the AE 905S. Insert the AE 905S to the optical interface on
the NE05E, with the AE 905S ejector lever
being locked.
Connect the other end of the feeder to the GPS
antenna and secure the joint.
1 Scenario I: Integrated Installation Scenario
Implement 1+3+3 waterproof protection for
the feeder-and-antenna joint. Use one cable
tie on each end of the feeder to secure the
feeder.
GPS
antenna
Cable ties 1+3+3
waterproof
protection
GTS antennas have high requirements on installation positions. For details about the position requirements, see
Appendixes 2.
NOTE
AE 905S

5
Install the dual-female conversion adapter on
the Protect interface of the lightning protection
component.
Install the lightning protection component.
Secure the nut on the Surge interface of the
lightning protection component.
Connect one end of the coaxial cable to the
Protect interface of the lightning protection
component, and use a wrench to secure the
joint.
Implement 1+3+3 waterproof protection for
the coaxial-cable-and-lightning-protection-
component joint. Use one cable tie on each
end of the tape to secure the adhesive tape.
Install the lightning protection component on the
ground bar on the right of the device and use
screws to secure it.
2 Scenario II: Separated Installation Scenario
Use a lightning-proof ground cable to
connect the GND interface of the lightning
protection component and the ground bar.
Wrap one layer
of insulation
tape.
Wrap three layers
of waterproof
tapes.
Wrap three layers
of insulation
tapes.
Use one
cable tie on
each end.
For requirements on the GPS installation, see GPS Satellite Antenna System Quick Installation Guide.
For requirements on the GPS antenna position, see Appendixes 2.
This document describes how to connect the ATN ATOM GPS to the GPS.
NOTE
Dual-female
conversion
adapter
lightning
protection
component
Protect
Surge
Connect the
GND interface
of the lightning
protection
component to
the ground bar.
Use OT M8 terminals as the lightning
protection component terminals.
NOTE

Insert the AE 905S to the optical interface on
the NE05E, with the AE 905S ejector lever
being locked.
2 Scenario II: Separated Installation Scenario
Remove the rubber plug, and connect the
GPS feeder to the AE 905S.
Use the GPS feeder to connect the Surge interface
of the lightning protection component to the GPS
antenna, and use a wrench to secure the joints.
For requirements on the GPS feeder joint production, see GPS
Satellite Antenna System Quick Installation Guide.
NOTE
6
10 Implement 1+3+3 waterproof protection. Use
one cable tie on each end of the tape to
secure the adhesive tape.
•Implement waterproof protection for the feeder-
and-lightning-protection-surge joint.
•Implement waterproof protection for the feeder-
and-GPS-antenna-N joint.
Wrap one layer
of insulation
tape.
Wrap three layers
of waterproof
tapes.
Wrap three layers
of insulation
tapes.
Use one
cable tie on
each end.

7
Installation Pre-processing
Open the cover and measure an 80 mm length of
the power cable at one end. Strip an 80 mm length of the black insulation
layer of the power cable.
80mm
10 mm
Strip a 10 mm length of the insulation layers of the
power cable cores. Install the power cable terminal and crimp the
metal part of the terminal.
Power cable terminal:
Expected installation result:
•One of the two power channels is an input channel and provides power for the NE05E, and the other
is an output channel and provides power for another NE05E.
The insulation layers of the power cable cores include two colors according to the
Chinese/European and American standards, as shown in the following table.
•When making power cables, prevent foreign matter from falling into the NE05E.
1 Installing the Power Terminal to be Connected to the NE05E
L
N
PE
Chinese/European standard American standard
Mark
Black
White
Green
Brown
Blue
Yellow green
NOTE