Huawei SmartAX MA5671 User manual

SmartAX MA5671 Desktop
Multi-service Access Equipment
Quick Start

2
1 Safety Precautions
To use the device properly and safely, read the safety precautions carefully before using
the device and strictly observe these precautions when using the device.
Safety precautions:
Do not look into the optical port without eye protection.
Keep the device out of the reach of children as the components or accessories may be
swallowed.
Install the device in strict compliance with the requirements of the supplier. Reserve
a space of at least 10 cm above and around the device for heat dissipation. During the
installation, keep the device away from heat or water sources, and electric appliances
that generate strong magnetic or electric fields, such as microwave ovens,
refrigerators, and mobile phones.
The power supply voltage of the device must meet the requirements on the input
voltage of the device.
Do not use any power adapters that are not in the standard configuration. Otherwise,
the device may malfunction or be unsafe.
Dry your hands before connecting or disconnecting cables. Stop the device and
switch the device off before connecting or disconnecting cables.
Do not place any object on the device, preventing the device from being damaged
due to overheating or deformation.
Prevent objects, such as metal or water, from entering the device through the heat
dissipation hole.
Switch the device off and disconnect all cables, including the power cable, network
cable, and phone cable, during periods of lightning activities.
Do not lead the strength member of the optical fiber or other metal parts indoors. Do
not connect network cables, phone cables, power adapters, or power adapter cables
outdoors, preventing device damage and bodily injuries that are prone to occur
during thunderstorms.
If an abnormality occurs, for example, liquid entering the device, smoke, unusual
sound, and smell, immediately stop the device, switch the device off, disconnect all
cables (such as the power cable, optical cable, and network cable) from the device,
and contact the authorized service center.
Do not disassemble the device without permission. In the event of a device fault,
contact the authorized service center.
Dispose of packing materials and old/abandoned devices in accordance to local laws
and regulations (recycling them is strongly recommended).

3
Do not change the structure, safety design, or performance design of the device
without prior authorization.
Fireproof precautions:
Keep the device away from large heat source equipment, bare flames, and
high-power devices, such as electric heaters, candles, and blow drier, to eliminate
safety risks.
Replace deteriorated cables or power socket facilities on the power supply line or
near the device in a timely manner to eliminate safety risks.
2 Installing the MA5671
NOTE
Do not install the MA5671 outdoors or in an outdoor cabinet.
The MA5671 can be horizontally placed on a workbench or mounted onto a wall. Do not
install the MA5671 in other modes, such as mounted to the ceiling.
Horizontally Placed on a Workbench
The following figure shows the MA5671 horizontally placed on a workbench.

4
Mounted onto a Wall
Step 1 Mark the positions of two holes (with a space the same as that between wall-mounting
holes) used for mounting the MA5671.
Step 2 Select a proper drill according to the outer screw diameter. Use a hammer drill to drill the
marked positions on the wall. Then, clean the wall and install two expansion bolts.
Step 3 Use a screwdriver to fasten the screws into the expansion bolts, leaving the heads of the
screws 3 mm over the wall. Then, mount the MA5671 to the screws.
NOTE
The tools and installation materials involved in the preceding installation steps must be
provided by customers.

5
3 Connecting Cables

6
Performing the Following Steps to Connect the MA5671 to Each Product
Based on the Preceding Cable Connections
Step 1 Use an optical fiber to connect the OPTICAL port on the MA5671 to the optical port in
the wall.
NOTE
The optical fiber connector connected to the OPTICAL port must be of the SC/UPC type.
The bending radius of optical fibers must be greater than 30 mm in optical fiber
deployment for proper optical fiber running.
Step 2 Use an Ethernet cable to connect the LAN port to network port on the PC or IP set top
box (STB).
Step 3 Use a power adapter to connect the POWER port to the power socket.
Step 4 Press ON/OFF to switch the MA5671 on.

7
4 Logging In to the Web Page
Performing the Following Steps to Log In to the MA5671's Web Page
Step 1 Set the IP address of the PC to be in the same network segment as the management IP
address of the MA5671. For example:
IP address: 192.168.100.100
Subnet mask: 255.255.255.0
NOTE
The default management IP address and subnet mask of the MA5671 are as follows:
IP address: 192.168.100.1
Subnet mask: 255.255.255.0
Step 2 Enter the management IP address of the MA5671 in the address bar of the browser and
press Enter.
Then, the login window is displayed.
Step 3 In the login window, enter the user name (telecomadmin) and password (default:
admintelecom), select a web page language, and click Login.
After the password is authenticated, the MA5671's web page is displayed.
If you perform no operation within 5 minutes after logging in to the web page, the
MA5671 automatically returns to the login page.
The MA5671 is automatically locked if you incorrectly enter the user name or password
for three consecutive times and will be unlocked in 1 minute.
After logging in to the web page using the initial user name and password, change the
login password.
5 Indicators
Table 5-1 Indicator status description (1)
Indicator
Status
Description
POWER
Steady green
The MA5671 is powered on.
Off
The MA5671 is powered off.

8
Indicator
Status
Description
PON
See Table 5-2.
LOS
See Table 5-2.
LAN1 through LAN4
Steady on
The Ethernet ports are properly
connected.
Blinking
The Ethernet ports are transmitting or
receiving data.
Off
The Ethernet ports are disconnected.
Both PON and LOS indicators indicate the status of the MA5671 in connecting to and
registering with the optical line terminal (OLT) of the service provider. Table 5-2
describes the status of the PON and LOS indicators.
Table 5-2 Indicator status description (2)
No.
Status
Description
PON
LOS
1
Off
Off
The MA5671 has been prohibited
by the OLT.
2
Blinking twice
one second
Off
The MA5671 is attempting to
connect to the OLT.
3
Steady on
Off
The MA5671 has connected to
the OLT.
4
Off
Blinking once two
seconds)
The RX optical power of the
MA5671 is lower than the optical
receiver sensitivity.
NOTE
According to Class B+, the optical
receiver sensitivity is –28 dB. If the
RX optical power of the MA5671
is less than –28 dB, the MA5671
fails to go online sometimes. The
LOS indicator blinks until the
MA5671 goes online.
5
Blinking twice
one second
Blinking twice
one second
The MA5671 is a rogue ONU
detected by the OLT.
NOTE
This function is available only
when the MA5671 uses GPON
upstream transmission.
6
Blinking once
two seconds)
Blinking once two
seconds)
The hardware is faulty.

9
6 FAQs
The LOS indicator is blinking.
If the LOS indicator blinks once two seconds, check whether the pigtail is securely connected
and whether the optical connector is clean.
If the MA5671 blinks twice a second, check whether it is a rogue ONU.
The PON indicator is off.
Check whether the optical fiber is securely connected to the OPTICAL port.
The MA5671 fails to register with the OLT. Contact the service provider for help.
How can I reset the MA5671?
Press Reset using a needle-type object.
How can I restore factory defaults?
Press Reset using a needle-type object for longer than 10s to restore factory defaults and reset
the MA5671. If this indicator is off and then on, the MA5671 restarts successfully.
7 Technical Specifications
Item
Specifications
Weight (including the power adapter)
About 700 g
Power supply for the integrated device
12 V DC, 1 A (European/British
standard)/2 A (American standard)
Power adapter input
European standard:
90–264 V AC, 50–60 Hz
British/ American standard:
90–270 V AC, 50–60 Hz
Operating temperature
0°C to +40°C
Operating humidity
5% to 95%, non-condensing

Warranty Card
Thank you for choosing Huawei Technologies Co., Ltd. To get better services, please
read this warranty card carefully, fill in the required information, and preserve this card
in good condition.
PERSONAL OR COMPANY
FULL NAME
Address/Postal Code
Telephone Number
Email
Product Type
Product Serial Number
Purchase Date
Invoice Number
Dealer's Name
Dealer's Address
Dealer's Telephone
Preserve well. No reissue.
Dealer's Seal