human care Carl-Oskar Instructions for use

Carl-Oskar
1
To secure that the walking-aid will function safely for the user, once per
year review of the walking-aid should be done.Therefore is the following
interventions recommended.
Wing nut
Control function.
Reectors
Make sure the reectors are still
there and visible.
CE-marking
Make sure that the CE-marking
is still there and readable.
Wheels
Make sure the wheels are not worn-out
and are spinning easily without any noice.
Lubrication
Gatebushings and hinges should be working without any noice.
Lubricate when needed.
Front forks
Make sure that the ball bearings is rmly attached. Check the front fork inertia
by allowing the wheel to swing between 3 and 9 o’clock. Both wheels shall swing
3 to 10 times with max 2 swings difference between each wheel.The inertia can
be adjusted by adjusting the nut on the top under the hub cover. Note! The nut
on the inside of the fork must not be touched.
Folding mechanism
Should be intact and the locking should function.
Seat
Make sure the seat is kept in place and
screws are tightened.
Stability
Control that all wheels are steadily on the ground and that there are no chassis
distortion.
Test driving
Make a nal control by test driving.
Cleaning
When cleaning the walker it is recommended machine washing, 60 degrees for
10 minutes.When using a pressure washer, do not wash directly to the bearings.
In addition to machine washing, regular cleaning with a mild cleanser is
recommended. Note! Do NOT use thinner, petrol or other solvents.
Post treatment
After washing, all connections, tight spaces and drainage holes should be blown
dry and sprayed with thin oil. If degreaser is used, should the moving parts be
lubricated.
The Paint
Control damages to the paint.To prevent corrosion, improve scratches.Touch-up
paint can be ordered from Human Care HC AB.
Pipe frame
Control weldings and screw attaches. If the corrosion is extensive shall the
rollator be replaced.
Handle
Must be xed. Make sure the handle pipes can be pushed
down to the chassis. Change the grip if needed.
Brakes
Control that both brakes and parkingbrakes are working.
Wires should be intact and stapped to the chassis.
RECONDITIONING MANUAL

2
Spareparts list
Product number:
Owner:
Notes:
Attended by:
Place and date:
Note!
Recondition must be done by a person how has good knowledge about how the
job should be performed.An incorrect performed recondition could result an
accident/incident. Don´t hesitate to contact your retailer if questions come up.
To secure safe usage of the product, only original parts should be used, these
have been developed and tested against current product standards. It is only with
original parts that the warranty and CE labeling is valid.
When disassembling of a wheel, the wheel nut and pin bolt must be replaced
since they contain a self-locking that will be destroyed when disassembling.
If the corrosion is more than a lm of rust the rollator shall be discarded and
return for recycling.
Intended use
The rollator should only be used as support whilst walking or as seating whilst
stationary. Do not alter the rollator yourself.
Specic instructions for reinforced Carl-Oskar.
Unique spareparts for reinforced Carl-Oskar models are listed in the bottom of
the sparepart list.These spareparts are strictly intended for use togheter with
the above mentioned products. Please note that other spare parts in the list
might not be suitable for these products.
RECONDITIONING MANUAL
No Designation Quantity Art. no Other information
Wheel kit 4 89010 For Carl-Oskar reinforced use 89089
1
2
3
Complete wheel
Wheel nut
Pin bolt
4
4
4
for rear wheel.
Bolt and nut must be exchanged
when disassembling the wheel.
1
2
3
Wheel kit air pumped
Complete wheel
Wheel nut
Pin bolt
4
4
4
4
89087 For Carl-Oskar reinforced use 89089
for rear wheel.
Bolt and nut must be exchanged
when disassembling the wheel.
Pin bolt & wheel nut 4 89032 For Carl-Oskar reinforced use 89091
2
3
Wheel nut
Pin bolt
4
4
for rear wheel.
Pin bolt and wheel nut must be
exchanged when disassembling.
Front fork kit 2 89085 From 200507
4
2
3
5
6
7
Front fork
Wheel nut
Pin bolt
Bearing
Locking nut
Hub cover
2
2
2
4
2
2
Pin bolt and wheel nut must be
exchanged when disassembling the
fork.
7 Hub cover 2 00864
Brake kit 2 89095 Pin bolt and wheel nut must be
8
9
10
11
12
13
14
15
16
Brake inner part
Brake outer part
Pop nut
Wear washer
Screw M6x6
Washer
Adjustment screw
Spring
Screw M6x16
2
2
2
2
2
2
2
2
2
exchanged when disassembling the
brake.
Note! Specic nut and pin bolt for
reinforced Carl-Oskar. Add 89091.
2 Wheel nut 2
3 Pin bolt 2
11 Wear washer 2 10-004 Wear washer turns when worn.
Handle kit 2 89055 For left and right.
17
18
19
Handle pipe
Handle brake complete
Handle ERGO
2
2
2
Note! Specic handle for Carl-Oskar
reinforced.Add 89033.
19 Handle ERGO 2 20-024 For Carl-Oskar reinforced use
89033.
Wing nut complete 2 50937 Lubricate the wing nut when needed.
20
21
22
Wing nut
Screw
Washer
2
2
2

99211-Rev K, (2014-08-11)
3
2
3
4
5
6
7
1
8
14
16
13
12
10
9
11
15
17
18
19
20
22
21
28
25
26
27
24
23
RECONDITIONING MANUAL
• Årstaängsvägen 21C, SE-117 43 Stockholm, Sweden •
• Tel. +46(0)8 - 510 132 00 • Fax +46(0)8 - 665 35 10 •
• www.humancaregroup.com •
23 Wire complete 2 89050
Wire housing
Wire
Wire lock
Wire end
2
2
2
2
Seat kit 1 89020 Not for Carl-Oskar reinforced.
24
25
26
27
28
Seat
Gate lock
Fold loop
Screw M6x20
Screw to gate lock
1
1
1
2
4
Seat complete 1 89070 Not for Carl-Oskar reinforced.
24
27
Seat
Screw M6x20
1
2
Tube protection 1 50949
26 Fold loop 1 10-009
Gate lock kit 1 10-018
25
28
26
Gate lock
Screw to gate lock
Fold loop
1
4
1
Reex 2 00028
Touch-up paint F2
Rear wheel kit 2 89089 Pin bolt and wheel nut must be exchanged
1
2
Complete wheel
Wheel nut
Pin bolt
2
2
2
when disassembling the wheel.
2
Rear wheel kit air
pumped
Complete wheel
Wheel nut
Pin bolt
2
2
2
2
89088 Pin bolt and wheel nut must be exchanged
when disassembling the wheel.
Tyre pressure max 2,0 bar.
Handle 2 89033 When changing the handle, the upper part
of the reinforcement beam must be removed.
2
Pin bolt & wheel nut for
rear wheel
Wheel nut
Pin bolt
2
2
2
89091 Pin bolt and wheel nut must be exchanged
when disassembling.
Spareparts reinforced Carl-Oskar (Art. no 61225, 61325, 61425)