human care Convertible Chair H-250 User manual

Converble Chair H-250
User Manual

2www.humancaregroup.com
Content
Assembly Process 3
Disassembly Process 5
Parts of the Chair 7
Parts of the Chair 8
Safety Notes 9
Operating the Chair 11
Maintaining the Chair 17
Troubleshooting 18
Specifications 18
Warranty 19
TYPE OF DOCUMENTANVÄNDARMANUAL
• This operations manual provides important instructions for the safe
use of Convertible Chair H-250.
• Please read this manual carefully and use the Convertible Chair only
after you have developed a full understanding of its safe and correct
use.
Converble Chair H-250
Part no: B1002-BL
• Keep this manual where you can consult it whenever necessary.
• The information contained in this manual is subjected to change
without notice.

3
www.humancaregroup.com www.humancaregroup.com
Section 1: Unpackaging the Chair
1-1) Open box from the side labeled “Open from this End”
1-2) Upon opening the outer box, remove the corrugated end cap and
wheel stop
(The wheel stop is a triangle corrugated piece that keeps the chair from
rolling)
1-3) Unlock all locking casters
1-4) Roll chair from side ofbox marked:”Open from this End”
1-5) Untie the string around caster at (patient) front-right side (Picture
1) (The purpose of this string is to avoid caster hitting foot frame.)
1-6) Save all packaging in a safe location for future use.
Section 2: Assembling Legrest
2-1) Lift legrest with one hand, and insert the “legrest adjustment
attachment” (Figure 1) to “Legrest adjustment holder” (Figure 2)
Section 3: Assembling Headrest
3-1) Remove tape (as shown in Picture 2) to free the carton that
includes the headrest
3-2) Lift (Grip) the reclining lever (wrapped with bubble wrap), so that
the back rest will be lifted 30degrees (by lifting backrest by 30 degrees
it is much easier to assemble the headrest)
3-2) Remove the headrest from the corrugated box, loosen and remove
headrest adjustment knob (as shown in Picture 3)
(NOfE: Place the headrest adjustment knob somewhere safe as you will
be reinstalling it shortly)
3-3) Insert the headrest into the backrest frame and re-attach
headrest adjustment knob
(Picture 4 through 6)
3-4) Attach the reclining cable to the two cable clamps that are along
the chair frame as shown in pictures 8 and 9 and figure 3.
(Insure there is no bending in the cable when attached to the clamps)
Assembly Process
Legrest
adjustment

4
www.humancaregroup.com
3-5) Reminder: Store the packaging box and materials in a safe place in
order that they may be used in future shipments.
Assembly Process

5www.humancaregroup.com 4
Section 1: Disassembling headrest
1-1) Detach reclining cable from the two (2) cable clamps noted in
pictures 1, 2 and figure 1.
1-2) Loosen and remove headrest adjustment knob. Lift and remove
headrest from the backrest frame. (Pictures 3, through 6)
Disassembly Process
1-3) Make sure to re-attach the headrest adjustment knob to avoid loss.
(Picture 7)
1-4) Install the removed headrest assembly in the original box and
place the box under the backrest as shown in picture 8.
1-5) Lift (Grip) the reclining lever J so that the back rest will be at about
a 30 degree angle.
(By lifting backrest by 30 degree it will be much easier to slide the box
into it’s storage position).
1-6) Tape the boxJ with the headrest assembly, in position as shown in
picture 8.
Section 2: Disassembling legrest
2-1) Lift the legrest with one hand and pull out the legrest adjustment
attachment from the legrest adjustment holder. (Figures 1 and 2)
*When disassemblingJ take out legrest adjustment attachment by
swinging the pivot latch as shown Fig.3.
figure 1
figure 2
figure 3

6
www.humancaregroup.com
Section 3: Packaging
3-1) Position the patient front-right caster so that the locking
mechanism is facing in towards the chair and set lock.
3-2) Wrap a piece of corrugated around the chair frame and tie a string
at front-right side caster
(looking from the rear of the chair)
(The purpose of this string is to avoid caster hitting foot frame.)
3-3) Make sure that front-left caster is steer-locked facing front.
3-4) Check the serial number on the chair and insure the serial number
labeled on the shipping box matches. If the serial numbers do not
match, cross out serial number on the shipping box in all locations and
write the actual chair serial number on the shipping box with a black
permanent marker.
3-5) Wrap entire chair with bubble wrap material.
3-6) Position the shipping box so that the end with “Open From this
End” marking is opened.
3-7) Roll the chair into the shipping box, with head of chair first.
3-8) Once chair is rolled completely into he shipping box lock all casters.
3-9) Install the corrugated wheel stops against the casters to keep chair
from rolling.
3-10) Tape wheel stops into position.
3-11) Install the corrugated end cap.
3-12) Tape the open end of the shipping box closed.
Disassembly Process

6 7
www.humancaregroup.com
Parts of the Chair

8
www.humancaregroup.com
You must understand the warnings and cautions in this manual to
use the Convertible Chair safely. Failure to observe the warnings and
cautions may result in serious injury and/or mechanical failure. Please
read all instructions carefully before using the chair.
o
You must heed the following warnings and cautions. Failure to
observe these safety precautions may result in personalinjury
or mechanical failure.
• Do not use the chair near an open flame (stove, cigarette, etc.) or a
high-temperature heat source.
• Do not use stairs or escalators to move an occupied chair whether in
the chair or the prone position.
• Do not use the chair in a hyperbaric (high oxygen content/high
atmospheric pressure) environment due to the possibility of static
discharge.
• The maximum occupant weight for the chair is 250 lbs. People who
weigh more cannot use the Convertible Chair H-250.
• Do not use the footrest as a step when getting into or out of the chair.
The footrest should be in its folded position to avoid tripping the
patient or tipping the chair.
• Take special care when going up or down a ramp or slope.Be sure to
lock the steering caster when traversing an incline or decline. Never
park the chair on a ramp or slope.
• Remove the seatbelt from around the patient when changing from the
prone to the chair position. Otherwise the seatbelt will tighten, which
may result in serious injury to the patient.
Parts of the Chair

8 9
www.humancaregroup.com
o
You must heed the following warnings and cautions. Failure to
observe these safety precautions may result in personal injury
or mechanical failure.
• Do not use the chair on gravel, wet, or frozen roads, or on any surface
that is extremely slick or wet.
• Caster locks are not designed to stop the chair. Do not use the caster
control pedals to stop the chair in motion.
• Take special care to lock the casters securely when reclining or
inclining the chair or when transferring the patient to or from the chair.
• Do not confuse the headrest and footrest when placing the patient in
the prone position.
• Always raise the armrests whenever the patient is lying on the chair in
the prone position.
• Make sure all persons and objects are clear of the chair when reclining
or inclining the chair.
• Do not allow the patient to sit on the chair when it is in the prone
position. Never sit or lean on the headrest or the legrest when the chair
is in the prone position.
o
You must heed the following warnings and cautions. Failure to
observe these safety precautions may result in personal injury
or mechanical failure.
• Do not move the chair using the armrest.
• The chair is designed for a single occupant. Never allow two or more
people to sit or lie on the chair. Do not place any other heavy object
on it.
• The Convertible Chair is not designed as a weight training or
rehabilitation apparatus. Never use it for such purposes.
• Do not jump up and down on the back cushion or seat cushion.
• Do not use a chair with any missing or damaged parts.
• Never disassemble or remodel the Convertible Chair. If problems
arise, contact Human Care or your authorized dealership.
Safety Notes

10
www.humancaregroup.com
Perform the following checks before using the chair:
1. Casters can be locked (individual lock type and steering control
type).
2. Reclining mechanism works smoothly and stops in any desired
position.
3. Height and angle of the footrest and the height, angle and depth of
the headrest can be adjusted properly.
4. Height adjustment of the armrests can be made properly.
5. Tilting mechanism can be operated smoothly and can be stopped in
any desired position.
If problems are found, contact Human Care at 1-877-822-7866
or your authorized Medical dealership.
Adjusting the Footrest
The Convertible Chair is packaged with the footrest folded up.
Safety Notes

10 11
www.humancaregroup.com
Lowering the footrest for a taU patient
The footrest can be lowered further if necessary to accomodate
a tall patient. A 5-mmAllen wrench and a 13-mm or adjustable wrench
are needed to perform this adustment.
o
Always use both hands when raising or lowering the footrest.
Otherwise an injury or accident may occur.
o
Be sure to tilt the legrest or the chair to avoid damaging the
underside of the footrest.
1. While using the Allen wrench to keep the stop bolt from turning,
use the adjustable wrench to remove the stop nut (shown in the
illustration).
2. Support the footrest from underneath with one hand and loosen the
footrest height adjusting grip with the other.
3. Slowly push the footrest down.
4. When the footrest reaches the desired height, tighten the grip fully.
5. Tilt the legrest up or the chair backwards slightly so the footrest
does not drag on the ground when moving the chair.
Adjusting the Legrest
The angle of the legrest can be adjusted to four levels.
o
Be sure to hold the footrest with one hand when performing
the angle adjustment. Moving the lever only may cause an
abrupt angle change, which may casue stress to the patient or
cause an accident or mechanical trouble.
Operating the Chair
Raising and lowering the footrest
Adjust the height of the footrest to comfortably accomodate the
patient.
o
Always use both hands when raising or lowering the footrest.
Otherwise an injury or accident may occur.
1. Support the footrest from underneath with one hand and loosen the
footrest height adjusting knob with the other.
2. Slowly push the footrest up or down.
3. When the footrest reaches the desired height, tighten the knob fully.
Positioning the footrest for use
o
Never use the footrest at any angle between 0 degrees and 90
degrees.Otherwise the footrest may suddenly fold or unfold
and cause an injury or accident.
1.Rotate the footrest to the 90-degree position for a patient
in the seated position.
2.Fold the footrest up completely for a patient in the prone position.

12
www.humancaregroup.com
Raising the legrest
1. Support the end of the footrest from underneath with both hands.
2. Slowly raise the legrest until you hear a click.
3. If you continue to raise the legrest, you will hear additional clicks.
Stop at the desired angle.
Lowering the legrest
1.Raise the footrest a little with one hand.
2. Grip the legrest angle adjusting lever with the other hand and slowly
lower the legrest.
Tilting the legrest for a tall patient
o
Be sure to tilt the legrest or the chair to avoid damaging the
underside of the footrest.
Raise the legrest to position two (next to lowest), three, or four
(highest) for a tall patient, as described above.
Adjusting the Headrest
The headrest allows the patient’s head to be held comfortably
and securely while they are in the chair.Make the depth and angle
adustment together with the height adustment to suit the figure of the
patient.
Adjusting the height
o
Always use both hands when raising or lowering the headrest.
Never let go of the reclining handle until the knob is tightened.
1. Hold the recline handle with one hand, and loosen the headrest
height adjusting knob with the other. Then slowly raise or lower the
headrest.
2. When the headrest reaches the desired height, tighten the knob fully.
Adjusting the depth and angle
The headrest aduster changes the depth and angle of the headrest at
the same time.
o
Never let go of the headrest until the headrest adjusting knob
is tightened.
1. Hold the headrest with one hand and loosen the headrest adjusting
knob with the other hand. Then adjust the headrest position by pushing
the headrest forward.
2. When the headrest position is determined, tighten the headrest
adjusting knob fully.
3. Straighten the headrest support to its original position
by restoring the depth/angle of headrest to home position.
4. Hold the headrest with one hand and loosen the headrest adjusting
knob with the other hand. Then pull the headrest backward and up to
restore it to the home position (flat to the back of the chair frame).
5. When the headrest is back in home position, tighten the headrest
adjusting knob.
Operating the Chair

12 13
www.humancaregroup.com
Adjusting the Headrest Side Supports
The headrest side supports help keep the patient’s head from turning
or drooping and help keep the neck straight.
o
Before the chair is transformed to the prone position, lower the
headrest so it is flush with the back cushion. Failure to do so
could cause the patient’s head to drop between backrest and
headrest, and an injury or accident may occur.
1. Hold the middle part of the headrest with one hand and slowly move
one side at a time forward with the other hand.
2. To retwn the headrest support to its original position, hold the
middle part with one hand and slowly pull one side at a time backward
with the other hand.
Adjusting the Armrests
The armrests function as guardrails to prevent the patient from falling
when the chair is in the prone position. They also function as the
supports for the patient’s upper body when in a sitting position.
The height of the armrests can be adjusted to five levels.
The height is set with the tip of the armrest height adjusting knob
inserted into one of the holes in the rear of the pipe. Pull the knob out
and raise
the armrest slowly until you hear a click, which indicates engagement.
Raising the armrest
o
After adusting the armrest make sure the armrest height adjusting knob is
locked in place, or injury may occur.
1.While holding the armrest with one hand, pull out the armrest height
adjusting knob with the other hand. Gently pull on the armrest to raise
it.
2. Once the armrest has reached the desired height, release the armrest
height adjusting knob. This locks the armrest into position.
Lowering the armrest
o
After adusting the armrest make sure the armrest height
adjusting knob is locked in place, or injury may occur.
1. While holding the armrest with one hand, pull out the armrest height
adjusting knob with the other hand. Gently push on the armrest to
lower it.
2. Once the armrest has reached the desired height, release the armrest
height adjusting knob. This locks the armrest into position.
Operating the Chair

14
www.humancaregroup.com
Steering the Chair
The Convertiable Chair H-250 can be steered in two modes: with the
steering locked or with all four casters able to move independently. The
left front caster is the motion control type. This caster has a control
pedal labeled “Steering” and is used primarily for steering.
Using the steering lock function
The steering lock function allows you to easily steer the chair in a
straight line. Only the left front caster has this function.
1. Step down on the back of the steering caster control pedal until it
clicks. Then move the chair in a straight line about 3 feet backward or
forward to set the lock. This action will keep the caster from swiveling
and allow better forward and backward movement of the
chair. The chair can now be moved with greater stability.
Using the 4-caster free function
In the 4-caster free mode, all four casters move independently, allowing
the chair to be easily brought alongside a bed.In this mode all four
casters are unlocked.
o
When setting the casters free by the caster control pedal, do
not put your finger in the square opening in the control pedal.
Do not use the 4-caster free function when moving a patient
across an incline.The chair may roll down the incline and an
injury may occur.
1. To ensure the casters are unlocked, step down on the front of the
control pedal of each caster.
Locking the Casters
The locking function holds the chair motionless when parking the chair,
when transforming it from the chair to the prone position or from the
prone to the chair position, and when transferring the patient to and
from a bed. Three casters (both rear and the right front)
are the individual lock type casters. These casters have control pedals
labeled “Brake.”
o
The caster lock is not designed to stop the chair in motion.Do
not operate the caster control pedal while moving the chair.
1. To lock the casters, step down on the back of the control pedal on
each individual lock type caster until it clicks into place, ensuring each
one is fully down. This locks both the caster swivel and wheel rotation.
2. To unlock the casters, step down on the front of the control pedal on
each individual lock type caster until the lock releases.
Operating the Chair

14 15
www.humancaregroup.com
Using the Tilt-n-Space Feature
The Tilt-n-Space feature is designed to tilt the chair within the frame
to ensure the patient’s comfort and safety while seated in the chair by
relieving pressure.
o
Never recline the patient to the prone (horizontal) position
before attempting to use the Tilt-n-Space feature.The chair
may recline abruptly and an injury or accident may occur.
Tilting the chair
o
Make sure that the casters are locked.Otherwise the force
applied may not allow the tilt mechanism to function properly.
1. Hold the push handle and the tilt lever at the same time and squeeze
them together with both hands as illustrated. Slowly push down.
2.When the back reaches the desired angle, release the tilt lever. The tilt
is adjustable to any angle up to 17 degrees from upright.
Returning the chair to its original position
o
Restore the tilt mechanism to the upright position before
reclining the chair to the prone position.Failure to do so may
cause the patient to slip head first from the chair and an injury
or accident may occur.
1. Hold the push handle and the tilt lever at the same time and squeeze
them together with both hands as illustrated. Slowly pull up.
2. When the desired angle is reached, release the tilt lever.
Operating the Chair

16
www.humancaregroup.com
Changing Between Chair and Prone Positions
The chair back stops at any angle between the prone (horizontal)
position and an upright angle of about 70 degrees.
The Convertable Chair is not designed to be used as a stretcher to move
patients and it is not recommended for such use.
o
Before reclining or inclining the chair, always ensure that the
casters are locked. Otherwise the chair may begin moving
during the reclining operation, and an injury or accident may
occur.
o
Always recline and incline the chair slowly.
Changing from the chair to the prone position
Putting the chair in the prone position allows easy transfer of the
patient from the chair to the bed and vice versa.
o
Restore the tilting mechanism to the upright position before
reclining the chair to the prone position. Failure to do so may
cause the patient to slip head first from the chair and an injury
or accident may occur.
You must restore the Tilt-n-Space mechanism to the upright position
before reclining the chair to the prone position.If you realize during
the reclining operation that the tilting mechanism is not in the upright
position, stop the operation immediately, return to the chair position,
and move the Tilt-n-Space mechanism to the upright position. Then
change the chair to the prone position.
o
Do not allow the patient’s hands to slip between the safety
guard and the frame, or injury may occur.
o
Always use both hands when raising or lowering the seat
back.
Operating the Chair
1. While holding the recline handle, squeeze the recline lever and
recline handle together as illustrated. Slowly lower the recline handle.
o
Do not snap the recline lever. Allowing the recline lever to snap back
into position may lead to mechanical problems.
2. Release the recline lever when the back reaches the desired angle.
o
Remove the seatbelt from around the patient when changing
from the prone to the chair position. Otherwise the seatbelt
will tighten, which may result in serious injury to the patient.
o
Always use both hands when raising or lowering the seat back.
1.While holding the recline handle, squeeze the recline lever and
recline handle together as illustrated. Slowly raise the recline handle.
o
Do not snap the recline lever.Allowing the recline lever to snap
back into position may lead to mechanical problems.
2. Release the recline lever when the back reaches the desired angle.

16 17
www.humancaregroup.com
Changing to the Trendelenburg Position
o
The Trendelenburg position should only be attempted when the patient
has been secured in the chair with a Medical-approved harness-type
restraint device. Failure to do so may cause the patient to slip head first
from the chair and an injury or accident may occur.
o
Never recline the patient to the prone position and then attempt to use
the Tilt-n-Space feature.
The chair may recline abruptly and an injury or
accident may occur.
o
Do not allow the patient’s hands to slip between the safety guard and
the frame, or injury may occur.
Operating the Chair
Maintaining the Chair
Checks
The Convertible Chair H-250 is designed for enhanced safety and
durability. It is subject to wear and tear resulting from the place,
length, and other conditions of use. For longer use, periodically inspect
all parts and have them replaced as needed.
• Check the cushions for rips or tears.
• Check the tilt and recline levers to make sure they move freely.
• Check the cables to make sure they are securely attached to the
locking cylinders.
• Check the anti-tipper bar and frame attachment member to make
sure they are not bent.
• Check the chair recline and Tilt-n-Space features to make sure they
are working properly.
Maintenance
Moisture can cause rusting and noisy operation. Take care to wipe off
any moisture present on the Convertible Chair.
o
Always use both hands when raising or lowering the seat back.
1. Tilt the chair back using the Tilt-n-Space mechanism
(as described on page 13).
2. While holding the recline handle, squeeze the recline lever and
recline handle (as described on page 15). Slowly lower the recline
handle.
o
Do not snap the recline lever.Allowing the recline lever to snap back into
position may lead to mechanical problems.
2. Release the recline lever when the back reaches the desired angle.
Cleaning
o
Before using any cleaning product, test it on the underside of
the chair seat. Never use any volatile fluid (thinner, gasoline,
etc.) that could cause discoloration or deterioration.
Use mild soap and water or a nonabrasive hospital-grade detergent
disinfectant to clean the chair. First, wet a cloth with the cleaning
product and wring it dry. Then gently wipe off the chair.

18
www.humancaregroup.com
Troubleshooting
Before contacting Human Care or your authorized dealer for repair,
please make the following checks.
Trouble Check Correction
Does not move Caster lock Release the caster lock.
Does not go straight Position of caster control pedal Use the steering lock function of
casters
Will not recline Wire cable Make sure the cable is attached to
the handle properly and the cable
is securely attached to the locking
cylinder.
Tilt-n-Space mechanism not
working properly
Wire cable Make sure the cable is attached to
the handle properly and the cable
is securely attached to the locking
cylinder.
Headrest/footrest not locked Tightness of the adjusting knob Tighten the adjusting knob.
Specifications
Product name H-250 convertible chair
Model H-250
Maximum occupant weight 250 lbs
Overall height Prone: 26 inches,Wheelchair:53 to 60 inches
Overall length Prone: 71 to 84 inches, Wheelchair: 49 to 51.5 inches
Overall width 24.5 inches
Weight 123 lbs
Seat width 17 inches
Seat depth 18.5 inches
Back angle 0 to 70 degrees
Tilt-n-Space angle 0 to 17 degrees
Headrest adjustable height 7 inches
Footrest adjustable height 6 inches
Casters Three individual lock type, one steering control type
Frame Steel pipe frame, aluminum
Cushion Nylon top coating, vinyl chloride coating

18 19
www.humancaregroup.com
Warranty
Convertible Chair H-250
PLEASE NOTE:The warranty below has been drafted to comply with
Federal Law applicable to products manufactured after July 4, 1975.
This warranty is extended only to the original purchaser/user of our
products.
This warranty gives you specific legal rights and you may also have
other legal rights, which vary from state to state.
Human Care warrants the chair frame to be free from defects in
materials and workmanship for a period of three (3) years from date of
purchase. Wear items including, but not limited to: upholstery, casters,
locking cylinder, release cable, recline release handle, guide rod wear
strips, and seat frame wear collars are warranted to be free of defects
in material and workmanship for a period of one (1) year. If within such
warranty period any such products shall be proven to be defective, such
product shall be repaired or replaced, at Human Care´s option.
This warranty does not include any labor or shipping charges incurred in
replacement part installation or repair of any such product. Medical's
sole obligation and your exclusive remedy under this warranty shall be
limited to such repair and/or replacement.
For warranty service, please contact Human Care. Do not return
products without our prior consent.
LIMITATIONS AND EXCLUSIONS The foregoing warranty shall not apply
to:
• Serial numbered products if the serial number has been removed or
defaced;
• Products subjected to negligence, accident, or improper operation,
maintenance, or storage;
• Products modified without Human Care´s express written consent
including, but not limited to, modification through the use of
unauthorized parts or attachments;
• Products damaged by reason of repairs made to any component
without the specific consent of Human Care; or to
• Products damaged by circumstances beyond Human Care´s control.
Such evaluation will be solely determined by Human Care. The
warranty shall not
apply to problems arising from normal wear or failure to adhere to
these instructions.
The foregoing warranty is exclusive and in lieu of all other express
warranties. Implied warranties, if any, including the implied warranties
of merchantability and fitness for a particular purpose, shall not extend
beyond the duration of the expressed warranty provided herein and
the remedy for violations of any implied warranty shall be limited to
repair or replacement of the defective product pursuant to the terms
contained herein. Human Care shall not be liable for any consequential
or incidental damages whatsoever.
This warranty shall be extended to comply with state/provincial laws
and requirements.

User Manual ENG Convertible Chair H-250 Rev B (2015-04-24)
HUMAN CARE SWEDEN (HQ)
Årstaängsvägen 21C
117 43 Stockholm
Phone:- [phone]
Fax:- [phone]
E-post: [e-mail]
www.humancare.se
HUMAN CARE CANADA
10-155 Colonnade Road
Ottawa, ON K2E 7K1
Phone:- 613.723.6734
Fax:- 613.723.1058
Email: [e-mail]
www.humancaregroup.com
HUMAN CARE UNITED STATES
4210 S. Industrial Drive, Suite 160
Austin, TX 78744
Phone: [phone]
Fax: [phone]
Email: [e-mail]
www.humancaregroup.com
HUMAN CARE AUSTRALIA
Unit 9, 271 Wells Road
Chelsea Heights, Victoria 3196
Phone:- [phone]
Fax:- [phone]
Email: [e-mail]
www.humancaregroup.com