Humanscale eFloat Go 2.0 User manual

2- Leg Adjustable Frame
EN 2
FR 19
ES 23
North America: [phone]
Europe: [phone]
Asia Pacific: [phone]

2
Important Safety Instructions
WHEN USING AN ELECTRICAL FURNISHING, BASIC PRECAUTIONS SHOULD ALWAYS BE
FOLLOWED, INCLUDINGTHE FOLLOWING:
READ ALL INSTRUCTIONS BEFORE USING (THIS FURNISHING).
DANGER - To reduce the risk of electric shock:
1. Always unplug this furnishing from the electrical outlet before cleaning or servicing
WARNING - To reduce the risk of burns, fire, electric shock, or injury to persons:
1. Unplug from outlet before putting on or taking o parts.
2. Close supervision is necessary when this furnishing is used by, or near children, invalids, or
disabled persons.
3. Use this furnishing only for its intended use as described in these instructions. Do not use
attachments not recommended by the manufacturer.
4. Never operate this furnishing if it has a damaged cord or plug, if it is not working properly, if it
has been dropped or damaged, or dropped into water. Return the furnishing to a service center
for examination and repair.
5. Keep the cord away from heated surfaces.
6. Never operate the furnishing with the air openings blocked. Keep the air openings free of lint,
hair, and the like.
7. Never drop or insert any object into any opening.
8. For Indoor Use Only. Do not use outdoors.
9. Do not operate where aerosol (spray) products are being used or where oxygen is being
administered.
10. To disconnect, turn all controls to the o position, then remove plug from outlet.
11. For loading always put heavier items at the bottom and not near the top in order to help
prevent the possibility of the furnishing tipping over.
12. The table is not complete until mated with a work surface, mount only approved work surfaces
in accordance with instructions. Failure to do so may cause instability, collapse, or failure of
electrical components.
13. Not to be used in locations where children, or people with cognitive disabilities are anticipated
to be present.
14. Review the assembly instructions to confirm that the appropriate critical components and
accessories are being used with the furnishing.
15. Disconnect from supply circuit before cleaning and maintenance.
16. Risk of fire and shock, Use only NISPT-2 type 18 AWG cord.
1 7. The table top must have a flame rating of 200 or less and smoke rating of 450 or less. Any
other material should be evaluated with the table frame to determine its acceptability.
DO NOT OVERLOAD DESK: To prevent the table from tipping or collapsing, make sure the desk is not
overloaded by the weight of the worksurface and items on table. Evenly distribute load; excess loads
near edges can reduce stability and lead to tip over.

3
• Worksurfaces must be rectangular and at least 0.75” (20mm) thick, depth 23.6”-31.5”, width
46”-70.9”.
• Do not exceed maximum load including weight of worksurface of 220lbs (100kg)
ATTENTION - To reduce the risk of burns, fire, electric shock, or injury to persons:
1. Power supply: AC100V- 240V,50/60Hz
2. Service Environment: 32-104°F
3. Unplug the power plug before cleaning, wipe the dust on surface with slight wet dishcloth
when cleaning, be careful not to let the drops into the internal parts, not loose the connector.
4. The electric box contains electronic components, metals, plastics, wires etc., so dispos of it in
accordance with each country’s environmental legislation, not the general household waste.
5. Check carefully to ensure correct and complete assembly before using.
6. Be familiar with all functions and program settings of the product before first use.
7. Close supervision is necessary when this furnishing is used by, or near children, invalids, or
disabled persons.
8. Slight noise caused by the V-ribbed belt or brake system due to structure will not have any
eect on the use of the equipment.
9. Corrosive or abrasive materials are forbidden to clean the equipment. Must ensure that the
cleaner used will not pollute the environment.
10. This appliance can be used by children aged from 8 years and above and persons with reduced
physical, sensory or mental capabilities or lack of experience and knowledge if they have been
given supervision or instruction concerning use of the appliance in a safe way and understand
the hazards involved. Children shall not play with the appliance.
11. Cleaning and user maintenance shall not be made by children without supervision.
12. If the supply cord is damaged, it must be replaced by the manufacturer, its service agent or a
similarly qualified person in order to avoid a hazard.
13. Please make sure there is no hazard sources in your operating environment. e.g., do not litter
the tools around. Always be careful to treat the packaging materials in order to avoid any
possible danger, e.g. plastic bag may lead to choking hazard to children.
14. Keep the original package of the equipment if necessary in case of the future use in
transportation
This marking indicates that this product should not be disposed
with other household wastes. To prevent possible harm to the
environment or human health from uncontrolled waste disposal,
recycle it responsibly to promote the sustainable reuse of
material resources. To return your used device, please use the
return and collection systems or contact the retailer where the
product was purchased. They can take this product for
environmental safe recycling.
Waste Disposal

or
or
Before Getting Started
If using a power drill, use a low torque setting.
• Do assemble product on a protective surface.
• Two or more people may be required to maneuver the table.
• After assembly, the table will need to have an initial set up/reset performed before table can be
used.
Philips Head Screw Driver Power Drill with Philips Driver bit Measuring Tape
1 2 3
(2) Right Beam
(2) Lifting Column (2) Left Beam (2) Wing Bracket
C-Leg
(2) Wing Bracket
T-Leg
(2) FeetT-Leg (2) Feet C-Leg (2) Connecting Rod
(1) Adapter Cable(1) Power Cord(1) Adapter Arm (1) Extension Cord
Note: Each shipment contains (1) set of
T-legs or (1) set of C-legs, not both
Note: Each shipment contains (1) set of
Wing Brackets forT-Leg or (1) set of Wing
Brackets for C-Leg, not both
(1) Handset (1) Power Adapter
Humanscale Worksurface
(CONFIGURATION SPECIFIC,
PACKAGED SEPARATELY)
1
5
9
2
10
4
7
3
6 8
4
11 12 13
Tools Required
Parts Included

5
(12) ST4.2 x 19mm
Button Head Wood
Screws
(8) M6 x 30mm
Button Head Screws
(8) M6 x 10mm
Button Head Screws
(1) 4mm Allen Key
(6) Cable Tie (6) ST4.2 x 12mm
Flat Head Wood Screws
A
F
B
G -
C D E
(4) M6 x 12mm
Flat Head Screws
(2) ST4.2 x 19mm Pan
Head Wood Screws
(Packaged Separately)
Hardware Included

6
1a
1b
1b
1c
1c 1a
eFloat GO 2.0
Assembly Instructions
1Align each Beam with side of each Lifting Column (1a). Secure using (2) M6 x 10mm Button Head
Screws per Beam (1b). Tighten using the 4mm Allen Key (1c)

7
C-Leg Option
T-Leg Option
C-Leg Option
T-Leg Option
2a
2b
2b
2c
2c
2a
2Lower each Wing Bracket onto top of each Lifting Column (2a). Secure using (2) M6 x 12mm Flat
Head Screws per Wing Bracket (2b).Tighten using the 4mm Allen Key (2c).

Foot for
C-Leg Option
Foot for
T-Leg Option
8
3Using the 4mm Allen Key, loosen the existing Button Head Screws and set screw on each Beam
(3a). Position both Connecting Rods between each set of Beams and slide the Connecting Rods
into each end of the Beam (3b).
4Place Feet onto Legs (4a). Secure the Feet to
the Legs using the (8) M6 X 30mm Button Head
Screws (4b) and tighten using the 4mm Allen
Key (4c).
3a
3b
3b
4a
4b
4c
4a

9
5Place your Worksurface upside down on a protective surface. Lift and place the Frame on top of
the Worksurface (5a). Place the Adapter Arm underneath the Beam (5b) and hold it into place with
your hand (5) while lowering the Frame.
6Adjust the width and position the Frame on the Worksurface per the following sections.
5a
5b
5c

10
A - Humanscale Worksurface
Align the legs to the following pilot holes highlighted below. Note: Only the four outer corner pilot holes
are included for alignment. Worksurfaces come with dierent pilot hole options depending on the size
ordered.
46” Wide Worksurfaces
52-70” Wide Worksurfaces
Legend
NeatTech(29” Deep Worksurfaces only)
eFloat Go 2.0 Base
eFloat Go 2.0 Handswitch
Keyboard Tray
FRONT

11
A
B
B -Your Own Worksurface
If using your own top, locate the Table Frame using the measurements listed below.
FRONT
Worksurface Depth A T-Leg C-Leg
23”
1 3/8”” for 46” wide
worksurfaces. All other
worksurfaces 2”
Until max base
width of 66.1”
is reached
8.75” 11.5”
24” 9.25” 12.5”
29” 11.75” 14.5”
30” 12.25” 15.5”
Worksurfaces between
23”- 30”
Position frame by
ensuring the foot is
centered with the depth
of the worksurface.
Position frame by
ensuring the foot is
centered with the depth
of the worksurface.

12
7Once the Frame is adjusted to the width of the Worksurface secure the width of the Frame by
tightening the existing (8) M6x 10 Button head screws using the 4mm Allen Key.
8Using the (12) ST4.2 x 19mm Button Head Wood Screws secure the Frame to the Worksurface (8a).
Locate the Adaper Arm and slide the Power Adapter into the Adapter Arm (8b).
8a
8b

13
9Moving to the other side of the worksurface secure the Hand Switch to the Worksurface in your
desired location using the provided (2) ST4.2 x 19mm Pan Head Wood Screws along the front edge
of worksurface (9b). If using a Humanscale UniversalWorksurface, pilot holes are positioned on
the left/right hand side of the worksurface in our recommended location(s).
9b

14
Motor Cord Port
Motor Cord Port
Power Adaptor Port
Lifting Column Cord
Lifting Column Cord
Adapter Cable
10 Plug the Adapter Cable into the Power Adapter (10a). Plug the Power Cord into the Power Adapter
(10b). Plug both ends of Cords from each Lifting Column into the back of the Hand Switch (10c).
If the Lifting Column Cord is not long enough, use the Extension Cord to reach the Hand Switch.
Install other end of Adapter Cable into the back of the Hand Switch (10c).
Note: As an option, use the provided (6) Cable Ties to secure cables to underside of worksurface
(10d), with either double sided tape or the (6) ST4.2 X 12mm Flat Head Wood Screws.
YOU MUST RESETTHE DESK BEFORE USE. FOLLOW INSTRUCTIONS ON INITIAL SETUP/RESET
UNDER HAND SWITCH (SEE PG. 15 or 16)
11 Flip your table right side up and plug into outlet. Reset the desk per instructions in following section.
10b
10a
10c 10d

15
Button introduction: There are 6 buttons that “ ” , “ ” , “ ” , “ ” , “ ” , “ ”
(1) “ ” : Adjust the desk upwards
(2) “ ” : Adjust the desk downwards
(3) “ “: User height memory setting position 1
(4) “ “: User height memory setting position 2
(5) “ “: User height memory setting position 3
(6) “ “: User height memory setting position 4
Hand Switch
Programmable
3 4
Side Vew
Front Vew
3 4
Side Vew
Front Vew
LED DISPLAY UP DOWN MEMORY
MINIMUM
HEIGHT
ADJ.
MEMORY
MAXIMUM
HEIGHT
ADJ.
USB Port USB-C Port
MEMORY MEMORY

16
Initial Setup/Reset
Initial Setup / Reset:
1) When the LED display shows “ ”, the desk starts the reset process. Keep pressing the “ ”
button until the desk reaches the lowest position and bounces up, the display shows the current
height, release the “ ” button and then the reset completes.
2) When the desk is in a static state, press and hold “ ” and “ ” buttons for 3 seconds
simultaneously and the desk starts reset process. Repeat the STEP 1 and then the reset is
completed. After that, the height you saved will be cleaned.
Quick Charge
Safe: Built-in over-temperature protection, over-current protection, short-circuit protection, etc., output
interface current-limiting protection can ensure that the product works within the normal current range;
Compatible:
The product is compatible with mainstream smart phones and laptops on the market, and
can quickly charge the device.
Output Parameters:
1) Single USB Type-C port output: MAX 45W, 5V=3A, 9V=3A, 12V=3A, 15V=3A, 20V=2.25A;
2) Single USB Type-A port output: MAX 27W, 5V=2A, 9V=2A, 12V=1.5A, 15V=1.8A, 20V=0.9A,
compatible with Xiaomi CHARGE TURBO, Huawei FCP/SCP, Samsung AFC protocol;
3) When both Type-C and Type-A are connected to the device, the output voltage drops to 5V to power
the device, and the MAX is 22.5W.
4) Note: When the standing desk is lifting, the charging function will be turned o, and when the
standing desk stops lifting, the charging function will return to normal.
Up/Down:
The height of the desk can be adjusted up or down by pressing the “ ” or “ ” button, and the
current height will show on the display.
Setting Presets:
1) When the desk is in a static state, press and hold the button “ ” for three seconds, the display
shows “ ”, which means the save is successful. Then adjust the desk to any height. Click the
“ ” button and the desk will adjust to the height you saved.
2) Buttons “ ”, “ ”, and “ ” all have the same height memory function as button “
”, repeat
the above steps to save the height to the corresponding position. Then click the button and the
desk will adjust to the height you saved.
IMPORTANT: You must RESET the desk before use.

17
Changing Units of Measurement:
Press and Hold the “ + 3” key for 3 seconds to toggle between Metric and Imperial.
LCD displays blinks the current height 3 times,which indicates that the setting has changed.
Adjusting Anti Collision Sensor Level Adjustment:
1) Simultaneously press and hold the “
” and “
” buttons for 5 seconds to switch the sensitivity.
One operation can switch to one level, divided into 3 levels—A-3, A-2, A-1.
2) The display shows “
” means the anti-collision function is on low sensitivity; the display shows
“
” means medium sensitivity; the display shows “ ” means high sensitivity.
3) When the desk rises or falls, it will rebound immediately when encountering obstacles to prevent
damage.
Setting Upper and Lower Limits
a) Press and hold the “
” + "4" button for 3 seconds to set the maximum height, and the LED
display will show "top";
b) Press and hold the “
” + "4" button for 3 seconds to set the minimum height, and the LED
display will show "bot";
c) Press and hold the “
” + "4" button for 3 seconds to clear the height limit value setting, and the
LED display will show "clr".
d) Entering the reset mode manually will not clear the recorded height limits.

Troubleshooting
Technical Data
Error Solution
Table does not move Ensure all cords are fully secured and the outlet your table is plugged into has power.
Table moves at a slow rate
Reset table.Then check if overloaded, max loading: 220lbs;
The desk is moving
downwards without any
operation
Automatically Self- Reset
Go down but not go up or
go up but not go down
Reset Table
The upper and downward
height is not enough
The desk could not lifted
Over work Restart after suspend for 18mins while connecting with power.
Words “E01” or “E02”
appear Let the desk rest for more than 18 minutes before it can be used normally.
Other codes appear and
there is no response after
pressing the “ ” button
Make sure that the cable is not damaged and the connection is normal. Power o
for more than 10 seconds.
Turn power on.
“ ”, is now displayed.
Press and hold the “ ” button to reset (follow Reset Function).
If the above operations are performed, the table still does not operate normally, please contact
customer service.
2-Leg Adjustable Frame
Power 120V (USA, Canada) or 220V
Maximum input current 3A
Input Voltage Range of the Power Supply 100--240V
Stand by power consumption, primarily <0.1W
Operating Temperature 0- 40OC
Height Range (Standard Range) 27.6”-46.9” (Without Tabletop)
Base Width 43.3”- 66.1”
Travel Speed 0.98 in/s (25 mm/s) (no load)
Noise Level <50dB
Maximum lift capacity (Including worksurface) 220lbs
Duty Cycle 10% Max. 2 min on, 18 mins o
18

19
Consignes de sécurité
importantes
Lors de l’utilisation d’un appareil électrique, des
précautions de base doivent toujours être prises,
notamment les suivantes:
Lire toutes les instructions avant d’utiliser (cet
appareil).
DANGER - Pour réduire le risque d’électrocution:
1. Débrancher toujours cet appareil de la prise
électrique avant de le nettoyer ou de l’entretenir
AVERTISSEMENT- Pour réduire les risques
de brûlures, d’incendie, d’électrocution ou de
blessures:
1. Débrancher la prise de courant avant de mettre
ou de retirer les pièces.
2. Une surveillance étroite est nécessaire lorsque
cet appareil est utilisé par, ou à proximité
d’enfants, d’invalides, ou de personnes
handicapées.
3. Utiliser cet appareil uniquement pour l’usage
auquel il est destiné, tel qu’il est décrit dans
ces instructions. Ne pas utiliser des accessoires
non recommandés par le fabricant.
4. Ne jamais faire fonctionner cet appareil si le
cordon ou la fiche est endommagé, s’il ne
fonctionne pas correctement, s’il est tombé, s’il
a été endommagé ou s’il a été immergé dans
l’eau. Renvoyer l’appareil à un centre de service
pour examen et réparation.
5. Tenir le cordon à l’écart des surfaces
chauantes.
6. Ne jamais faire fonctionner l’appareil lorsque
ses ouvertures d’air sont bloquées. Veiller à ce
que les ouvertures d’aération soient exemptes
de peluches, de cheveux et d’autres éléments
similaires.
7. Ne jamais laisser tomber ou insérer un objet
dans une ouverture.
8. Pour usage intérieur uniquement. Ne pas
utiliser à l’extérieur.
9. Ne pas opérer là où des produits en aérosol
(vaporisateur) sont utilisés ou là où de l’oxygène
est administré.
10. Pour débrancher l’appareil, mettez toutes les
commandes en position d’arrêt, puis retirez la
fiche de la prise de courant.
11. Placer toujours les objets les plus lourds en bas
et non en haut afin d’éviter que l’appareil ne se
renverse.
12. La table n’est pas complète tant qu’elle n’est
pas jumelée à une surface de travail. Ne
montez que des surfaces de travail approuvées,
conformément aux instructions. Le non-respect
de cette consigne peut entraîner une instabilité,
un eondrement, ou une défaillance des
composants électriques.
13. Ne pas utiliser dans des endroits où des
enfants ou des personnes sourant de troubles
cognitifs sont susceptibles d’être présents.
14. Examiner les instructions d’assemblage pour
confirmer que les composants essentiels et
les accessoires appropriés sont utilisés avec le
produit.
15. Débrancher le circuit d’alimentation avant le
nettoyage et l’entretien.
16. Risque d’incendie et d’électrocution, utiliser
uniquement un cordon de 18AWG de type
NISPT-2.
17. Le plateau de table doit avoir un indice de
flamme de 200 ou moins et un indice de fumée
de 450 ou moins.Tout autre matériau doit être
évalué avec le cadre de table pour déterminer
sa conformité.
Voir page 2
NE PAS SURCHARGER LE BUREAU: Pour éviter
que la table ne bascule ou ne s’eondre, assurez-
vous que le bureau n’est pas surchargé par le
poids de la surface de travail et des objets posés
sur celle-ci. Répartir uniformément la charge; une
charge excessive près des bords peut réduire la
stabilité et entraîner un basculement.
• Les surfaces de travail doivent être rectangulaires
et avoir une épaisseur d’au moins 0,75 pouces
(20mm), une profondeur de 23,6 pouces à 31,5
pouces (60cm à 80cm), et une largeur de 46
pouces à 70,9 pouces (116,8cm à 180cm).
• Ne pas dépasser la charge maximale, y compris
le poids de la surface de travail, qui est de 100kg
(220lb).
ATTENTION- Pour réduire les risques de brûlures,
d’incendie, d’électrocution ou de blessures:
1. Alimentation électrique: AC100 V- 240 V,
50/60 Hz
2. Environnement de service: 0 à 40°C (32 à 104°F)
FR

20
3. Débranchez la fiche d’alimentation avant le
nettoyage, enlever la poussière sur la surface
avec un chion légèrement humide lors du
nettoyage, faites attention à ne pas laisser
tomber des gouttes dans les parties internes;
ne pas desserrer le connecteur.
4. Le boîtier électrique contient des
composants électroniques, des métaux, des
plastiques, des fils, etc. qui doivent êtres
mis au rebut conformément à la législation
environnementale de chaque pays, et non pas
dans les déchets ménagers généraux.
5. Vérifiez soigneusement que l’assemblage est
correct et complet avant de l’utiliser.
6. Familiarisez-vous avec toutes les fonctions et
tous les réglages du programme de l’appareil
avant votre première utilisation.
7. Une surveillance étroite est nécessaire lorsque
cet appareil est utilisé par, ou à proximité
d’enfants, d’invalides, ou de personnes
handicapées.
8. Le léger bruit causé par la courroie striée
en V ou le système de freinage en raison
de la structure n’aura aucune incidence sur
l’utilisation de l’équipement.
9. Il est interdit d’utiliser des matériaux corrosifs
ou abrasifs pour nettoyer l’appareil. Vous devez
vous assurer que le nettoyant utilisé ne pollue
pas l’environnement.
10. Cet appareil peut être utilisé par des enfants de
8 ans et plus et par des personnes ayant des
capacités physiques, sensorielles ou mentales
réduites ou un manque d’expérience et de
connaissances s’ ils sont supervisés ou ont
reçu des instructions concernant l’utilisation de
l’appareil en toute sécurité et s’ils comprennent
les risques encourus. Les enfants ne doivent
pas jouer avec l’appareil.
11. Le nettoyage et l’entretien par l’utilisateur ne
doivent pas être eectués par des enfants sans
surveillance.
12. Si le cordon d’alimentation est endommagé, il
doit être remplacé par le fabricant, son agent
de service ou une personne de qualification
similaire afin d’éviter tout danger.
13. Veillez à ce qu’il n’y ait pas de sources de
danger dans votre environnement de travail, par
exemple en évitant de laisser traîner des outils
par terre. Veillez toujours à traiter les matériaux
d’emballage de manière à éviter tout danger
éventuel, par exemple un sac en plastique peut
présenter un risque d’étouement pour les
enfants.
14. Conservez l’emballage d’origine de l’équipement
dans l’éventualité où vous devez le transporter.
Voir page 3
Avant de commencer
Si vous utilisez une perceuse électrique, utilisez un réglage de
couple faible.
• Assemblez le produit sur une surface protectrice.
• Deux personnes ou plus peuvent être nécessaires pour
manœuvrer la table.
• Après l’assemblage, la table devra faire l’objet d’un réglage
initial/d’une réinitialisation avant de pouvoir être utilisée.
Voir page 4
Outils nécessaires
①Tournevis à tête Philips
②Perceuse électrique avec embout Philips
③Ruban à mesurer
Voir page 4
Pièces incluses
①(2) Colonne de levage
②(2) Poutre gauche
③(2) Poutre droite
④Note: Chaque envoi contient (1) jeu de supports
d’aile pour patte en T ou (1) jeu de supports d’aile pour
patte en C, pas les deux.
(2) Support d’aile
⑤Note: Chaque envoi contient (1) jeu de pattes en T
ou (1) jeu de pattes en C, mais pas les deux.
(2) Patte en T
(2) Patte en C
⑥(2) Tige de connexion
⑦(1) Combiné
⑧(1) Adaptateur de courant
⑨(1) Bras d’adaptation
⑩(1) Cordon d’alimentation
⑪(1) Câble adaptateur
⑫(1) Cordon de rallonge
⑬Surface de travail Humanscale (CONFIGURATION
SPÉCIFIQUE, EMBALLÉ SÉPARÉMENT)
Voir page 4
Quincaillerie incluse
A. (8) Vis à tête ronde
B. (8) Vis à tête ronde M6 x 30 mm
C. (12) Vis à bois à tête ronde ST4.2 x 19 mm
D. (6) Attache-câble
E. (6) Vis à bois à tête plate ST4.2 x 12 mm
F. (1) Clé hexagonale de 4mm
G. (4) Vis à tête plate M6 x 12 mm
H. (2) Vis à bois à tête cylindrique ST4.2 x 19mm
(emballé séparément)
Voir page 5