Hydor HVFB User manual

HVFB Inst Issue 3: 18.06.15
Installation and Maintenance Instructions.
THESE INSTRUCTIONS MUST BE READ FULLY BEFORE COMMENCING INSTALLATION.
Owner / installer: The life of this apparatus and its eciency will be increased if
its use and maintenance is carried out in accordance with these instructions and
current statutory requirements. The installation and initial adjustments should be
carried out by a qualified and competent technician. Hydor Limited should be
consulted before substituting or fitting parts from another manufacturer. It is the
responsibility of the installer to verify that the installation is in accordance with
the following standards and the owner is given the current User’s Manual.
Any modifications to the fan or its installation, even the smallest
modification, change or elimination of security components or pieces that
influence the eciency or loss of ventilation, will result in the CE Certification
and Hydor’s warranty being cancelled.
Code Supply FL Amps Watts Weight kg
HVFB30 230V/1Ph/50Hz 0.22 50 3.8
HVFB45 230V/1Ph/50Hz 0.38 110 5.5
1. General
1.1 It is important these Installation and Maintenance Instructions are fully
adhered to.
1.2 Full details of the unit supplied are shown on the product nameplate. If in
doubt about any detail contact Hydor or its agents for clarification.
1.3 All electrical installation must be carried out by suitably qualified and
competent personnel in accordance with all current statutory
requirements.
1.4 These instructions cover only the Hydor product and do not include the
supply or installation of any safety equipment that may be required e.g.
adequate guarding or protection from rotating parts and proper electrical
isolation.
1.5 Any declarations made by Hydor about product installation and safety, are
HVFB Typhoon Fan
incorrect
correct, minimum height 5mm

HVFB Inst Issue 3: 18.06.15HVFB Inst Issue 3: 18.06.15
dependant on the fan equipment being used within installations which
themselves meet the requirements of the relevant Standards and
Directives of your region.
1.6 The fan must be installed indoors in a dry, sheltered position and is
designed for use in an ambient temperature of up to 40°C. The fan is not
suitable for corrosive or explosive atmospheres.
1.7 The installer should provide easy access to the fan to facilitate future
maintenance.
1.8 The installer should ensure the fan is adequately supported.
1.9 This product is not intended for use by persons (including children) with
reduced physical, sensory or mental capabilities, or lack of experience and
knowledge, unless they have been given supervision or instruction
concerning use of the product by a person responsible for their safely.
Children should be supervised to ensure that they do not play with the
product.
WARNING The fan must be isolated from the power supply during
installation and maintenance. The fan is supplied pre-wired to a
standard three pin plug and must be earthed in accordance with the
local regulations.
2. Installation
2.1 Upon receipt, the fan equipment should be visually inspected to check for
any damage.
2.2 Check the details on the motor rating plate to ensure that the correct
power supply (voltage, frequency and phase) is available. An incorrect
power supply will lead to permanent damage to the fan motor.
2.3 Floor mounting - Position the fan on a level surface where both the fan
and electrical cable will not cause a hazard. The cable must not be pulled.
2.4 Wall mounting (HVFB-30 & HVFB-45) – Securely fix the fan to a structurally
sound wall using suitable fasteners and the mounting brackets provided.
Ensure that the wall is able to support the cantilevered fan weight.
WARNING The fan must be isolated from the power supply before
adjusting any operating conditions apart from altering the fan speed.
3. Set up
3.1 Before power is supplied to the unit, ensure that the impeller is free to
rotate.
3.2 Check that the motor amperage draw does not exceed the nameplate
rating.
3.3 Speed - The fan has three speed settings, 1 – 3 (slow, medium, fast) with 0
being the o position.
3.4 Angle of Tilt – Release the retaining knobs, hold the fan and adjust the
angle of tilt to the desired position. Tighten the retaining knobs securely.
4. Fan Maintenance
4.1 Inspection of the fan at least once every 12 months is recommended to
ensure that the motor, fan blades, and supporting guards, are clean. Any
build up of dust and deposits on the blades or guards should be removed
using a non-abrasive cleaner.
4.2 All fastenings should be checked for tightness. In addition, all rotating
items should be checked.
4.3 Bearings are lubricated for life and will not need a detailed inspection.
WARNING The HVFB-30 and HVFB-45 fans are fitted with an auto-reset
thermal contact which switches the fan o in the event of a fault
condition. Once the motor cools down the fan may start unexpectedly.
Only a suitably qualified and competent person may carry out
maintenance after the electrical supply has been isolated.
Wall Mount Parts (optional only)
1. Wall mount parts must be installed on a stable, strong and permanent
concrete wall which must be in 90° vertical to the ground level. Please
check by qualified technician before installation.
2. Please use the screws included in the package for installation.
V-shape base tube
U-shape base tube
swell plastic button
self-tapping screw ST5x35
half-round head screw M4x12
half-round head screw M4x20
INSTALLATION AND CAUTIONS
HVFB-30
HVFB-45

HVFB Inst Issue 3: 18.06.15HVFB Inst Issue 3: 18.06.15
Code A B D H Weight kg
HVFB30 390 200 360 405 3.8
HVFB45 530 195 495 530 5.5
3. The pair of wall mount parts for HVFB-45 must be installed on the same level.
4. Wall mounted parts must be installed by qualified technician to avoid
hazard.
5. Periodic inspection by qualified technician for stability of wall mount parts
and the fan unit is necessary.
6. Dimensional Data
Notes

HVFB Inst Issue 3: 18.06.15HVFB Inst Issue 3: 18.06.15
NotesNotes

HVFB Inst Issue 3: 18.06.15
Guarantee
Hydor or its agents will, within a period of one year from the date of dispatch
from their works, at its option, replace any goods, which are proven to have
defects as a result of defective materials or workmanship. The goods must be
inspected by a Hydor ocial and if necessary returned, with a Returns Note
Number, carriage paid, for further examination.
Hydor Ltd
Hydor
Unit 8, Parkers Close, Downton Business Centre,
Downton, Salisbury, Wiltshire, SP5 3RB, UK
Tel: [phone]
Fax: [phone]
Email: [e-mail]
Web: www.hydor.co.uk
idealair group
Unit 1, Building 1, Sydney Corporate Park,
85 O’Riordan Street, Alexandria NSW 2015
Tel: [phone]
Fax: [phone]
Email: [e-mail]
AMS
11 Ingrid Road, Montague Gardens,
7442 Cape Town, Western Cape
Tel: [phone]
Fax: [phone]