HydraMaster DriMaster Upholstery Tool User manual

Upholstery Tool
Patent Pending
Owners Manual
RR

Upholstery Tool
Table of Contents Page
Getting Started ......................................................... 1
Adjusting Water Volume ..................................... 1
Adjusting Vacuum Relief ..................................... 2
Maintenance ............................................................ 3
Removing and Reinstalling the Clear Access Cover.. 3
Cleaning the Hose and Manifold ...........................
Cleaning the Solution Injector Bar .........................
Cleaning the Inline Filter ...................................... 5
Copyright© 1999
D-163-010
No part of this manual may be reproduced or used in any form or by any means (i.e. graphic, electronic, photocopying or electronic
retrieval systems) without the express written permission of the HYDRAMAST R© Corporation. All rights reserved.
Revised August 20, 2001
Patent Pending

HydraMaster Corporation 1/25/00
DriMaster Upholstery Tool Page 1
Getting Started
To Begin Cleaning:
1. Attach the solution hose to the
Solution Quick Connect. A 1-2
or 2 vacuum hose can be attached
to the Vac Hose Manifold.
2. Adjust the water volume by turning
the Needle Valve knob. By turning
the knob counterclockwise, the
water volume will increase. By
turning the knob clockwise the
water volume will decrease. The
amount o water volume you need
will vary with the type o machine
you are cleaning with.
To Adjust Water Volume Using the Needle Valve Knob:
A. Close the Needle Valve.
B. While the machine is running, turn the Solution Valve to the ON position.
C. Slowly open the Needle Valve until water is lowing across the entire
injector bar (without overspray).
Note: The amount o vacuum and
pressure produced by your machine
will determine the overspray on the
Solution Injector Bar.
3. The Solution Valve is only an ON/
OFF valve; the patented Solution
Injector Bar makes a trigger valve
unnecessary.
To turn the water ON, the Solution
Valve on the upholstery tool head
needs to be turned clockwise. Let the water run continuously or a ew minutes to
allow the hot water to reach the upholstery tool.

Page 2 DriMaster Upholstery Tool
HydraMaster Corporation
1/25/00
When the Solution Valve is turned to the ON position, the water will orm a sheet
across the Solution Injector Bar. Be careful not to touch the Solution Injector Bar, it
may cause severe burns!
To Adjust the Vacuu Relief:
There may be situations in which you wish to reduce the vacuum power to the
head o the tool.
4. To adjust the Vacuu Relief; hold the tool with your le t hand and with
your right hand, hold the hose where it connects to the tool. Gently pull
the hose away rom tool while twisting the hose until the Vacuu Relief
holes are exposed. Readjust the water low as required.
5. Once the hot water has reached the tool you are ready to clean.
It may be necessary to periodically clean the inside o the tool, hose, and mani old.
Debris can build up over time, restricting the vacuum low.
CAUTION
!

DriMaster Upholstery Tool Page 3
HydraMaster Corporation 1/25/00
Re oving and Reinstalling the Clear Access Cover
1. Insert a putty kni e into the ront edge o
the Vacuu Slot.
2. Pry up on the clear cover while holding
your thumb on the top o the cover.
3. To reinstall the Clear Cover be sure the
large portion o the taper is inserted irst.
CAUTION: Cover may come out i not
installed properly.
Maintenance
8/20/01

Page 4 DriMaster Upholstery Tool
HydraMaster Corporation
1/25/00
4. Slide the wide end o the cover into the
tool towards the ront o the head.
5. Using your thumb, press the narrow end o
the cover to snap it into place.
Cleaning the Hose and Manifold:
The Vacuu Hose can be removed at the tool by ollowing the same proce-
dure as Adjusting the Vacuum Relie , but instead, pull the hose completely
rom the tool. This will give you access to the back o the tool and will also
allow you to remove any visible debris rom the hose.
To clean the Vacuu Manifold, simply remove debris where the Vacuu Hose o the
machine is normally connected.
Cleaning the Solution Injector Bar:
The Solution Injector Bar needs to be cleaned
with a .006 eeler gauge.
Slide the eeler gauge into the small
slot.Gently slide the gauge back and
orth to clear any debris rom the opening.
The Solution Injector Bar is made rom aluminum, be care ul not to apply excessive
orce or use an inappropriate tool when clearing debris rom the slot.
8/20/01
CAUTION
!

DriMaster Upholstery Tool Page 5
HydraMaster Corporation 1/25/00
5. Cleaning the Inline Filter:
The Inline Filter can be removed by using an n and s wrench (as
shown in photo). Once the ilter is removed, use a so t brush to clean it.
When reinstalling the ilter, it is not necessary to use thread sealant. This
should be checked on a weekly basis.
8/20/01

Page 6 DriMaster Upholstery Tool
HydraMaster Corporation
1/25/00
HydraMaster/CleanMaster Corporation
11015 47th Ave West
Mukilteo, WA 98275
For any Warranty or Service questions please call our
Customer Service Department
[phone]
8/20/01