Hydrotech 565BM-75 User manual

565BirmWaterFilters

Installation and Operation Manual
REVISION # 0
REVISION DATE May 4,2015
#54586
1. Read all instructions carefully before operation.
2. Avoid pinched o-rings during installation by applying (provided with install kit) NSF
certified lubricant to all seals.
3. This system is not intended for treating water that is microbiologically unsafe or of
unknown quality without adequate disinfection before or after the system.
CanadianHeadOffice
655ParkSt.
Regina,SKS4N5N1

U.S.HeadOffice
843710thAvenueNorth
GoldenValley,MN55427

Safety Guide
 Check and comply with your provincial /
state and local codes. You must follow
these guidelines.
 Use care when handling the filter tank. Do
not turn upside down, drop, drag or set on
sharp protrusions.
 The system works on 12 volt-60 Hz electri-
cal power only. Be sure to use only the
included transformer.
 Transformer must be plugged into an in-
door 120 volt, grounded outlet only.
 WARNING: This system is not in-
tended for treating water that is microbio-
logically unsafe or of unknown quality
without adequate disinfection before or
after the system.
For your safety, the information in this manual must be followed to minimize the risk of
electric shock, property damage or personal injury.
Be sure to check the entire unit for any shipping damage or parts loss. Also note damage to
the shipping cartons. Contact the transportation company for all damage and loss claims.
The manufacturer is not responsible for damages in transit.
Small parts, needed to install the softener, are in a parts bag. To avoid loss of the small
parts, keep them in the parts bag until you are ready to use them.
Unpacking / Inspection
PAGE
Unpacking / Inspection 2
Safety Guide 2
Proper Installation 3
Specification 4
Before Starting Installation 5
Sizing Requirements 7
Installation Instructions 8
System Start Up 10
About The System 12
Maintenance 14
Main Repair Parts 16
Trouble Shooting 23
Warranty 24
Table of Contents
2

Proper Installation
This water filter system must be properly installed and located in accordance with the
Installation Instructions before it is used.
 Do not install or store where it will not be
exposed to temperatures below freezing or
exposed to any type of weather. Water
freezing in the system will break it. Do not
attempt to treat water over 100°F.
 Do not install in direct sunlight. Excessive
sun or heat may cause distortion or other
damage to non-metallic parts.
 Properly ground to conform with all gov-
erning codes and ordinances.
 Use only lead-free solder and flux for all
sweat-solder connections, as required by
state and federal codes.
 Maximum allowable inlet water pressure is
125 psi. If daytime pressure is over 80
psi, night time pressure may exceed the
maximum. Use a pressure reducing valve
to reduce the flow if necessary.
 WARNING: Discard all unused parts and
packaging material after installation. Small
parts remaining after the installation could
be a choke hazard.
3

Specifications
 Continuous operation at flow rates greater than the ser-
vice flow rate may affect capacity and efficiency per-
formance.
 The manufacturer reserves the right to make product
improvements which may deviate from the specifications
and descriptions stated herein, without obligation to
change previously manufactured products or to note the
change.
 Peak flow rates are intended for intermittent use only
and are for residential application only
 At the stated service flow rates, the pressure drop
through these devices will not exceed 15 psig
ServiceFlowRates
Normal 4.0gpm 5.0gpm 7.0gpm 10.0gpm 12.0gpm
Peak 5.0gpm 7.0gpm 10.0gpm 12.0gpm 15.0gpm
MicronRating 15‐20micron 15‐20micron 15‐20micron 15‐20micron 15‐20micron
BackwashFlowRate 4.0gpm 5.0gpm 7.0gpm 10.0gpm 14.0gpm
FilterMedi aVolume‐CubicFeet 0.75ft
3
1.0ft
3
1.5ft
3
2.0ft
3
3.0ft
3
FilterTankSi ze 8x44 9x48 10x54 12x52 14x65
TankJacket/MediaLoaded Yes Yes Yes No No
ShippingWeight 79lbs 118lbs 144lbs 198lbs 342lbs
ServiceFlowRates
Normal 4.0gpm 5.0gpm 7.0gpm 10gpm 12.0gpm
Peak 5.0gpm 7.0gpm 10.0gpm 12.0gpm 15.0gpm
BackwashFlowRate 3.5gpm 4.0gpm 5.0gpm 7.0gpm 10.0gpm
FilterMedi aVolume‐CubicFeet 0.75ft
3
1.0ft
3
1.5ft
3
2.0ft
3
3.0ft
3
FilterTankSi ze 8x44 9x48 10x54 12x52 14x65
TankJacket/MediaLoaded Yes Yes Yes No No
ShippingWeight 50lbs 60lbs 78lbs 95lbs 138lbs
ServiceFlowRates
Normal 2.0gpm 3.0gpm 5.0gpm 6.0gpm 7.0gpm
Peak 3.5gpm 5.0gpm 8.0gpm 10.0gpm 12.0gpm
BackwashFlowRate 3.5gpm 4.0gpm 5.0gpm 7.0gpm 10.0gpm
FilterMedi aVolume‐CubicFeet 0.75ft
3
1.0ft
3
1.5ft
3
2.0ft
3
3.0ft
3
FilterTankSi ze 8x44 9x48 10x54 12x52 14x65
TankJacket/MediaLoaded Yes Yes Yes No No
ShippingWeight 93lbs 120lbs 164lbs 207lbs 330lbs
ServiceFlowRates
Normal 4.0gpm 5.0gpm 8.0gpm 10.0gpm
Peak 7.0gpm 8.0gpm 10.0gpm 12gpm
MicronRating 3‐5micron 3‐5micron 3‐5micron 3‐5micron
BackwashFlowRate 5.0gpm 7.0gpm 10.0gpm 14.0gpm
FilterMedi aVolume‐CubicFeet 0.75ft
3
1.0ft
3
1.5ft
3
2.0ft
3
FilterTankSi ze 8x44 9x48 10x54 12x52
TankJacket Yes Yes Yes No
ShippingWeight 90lbs 135lbs 205lbs 255lbs
ALLFILTERS
PlumbingConnections
ElectricalRequirements
WaterTemperature
WaterPressure
3/4"(Optional1")
Input120V60Hz‐Output12V650mA
Min39‐Max.100degreesFahrenheit
Min.20‐Max.125psi
48NEX‐75 585NEX‐100 585NEX‐150 585NEX‐200
485NU‐75 585NU‐100 585NU‐150 585NU‐200 585NU‐300
585TO‐75 585TO‐100 585TO‐150 585TO‐200 585TO‐300
585MM‐75 585MM‐100 585MM‐150 585MM‐200 585MM‐300
Specifications
Specifications
Specifications
Specifications
565BM-75 565BM-100 565BM-150 565BM-200 565BM-300
785TO-75 785TO-100 785TO-150 785TO-200 785TO-300
785NU75 785NU-100 785NU-150 785NU-200 785NU-300
785NEX75 785NEX-100 785NEX-150 785NEX-200
785NU-300
4

Birm Filter
A backwashing-type filter containing special
media that causes the iron in the air-injected
water to precipitate throughout the filter bed
This process produces an iron removal ca-
pacity of up to 30,000 ppm. The media re-
quires no chemical regenerant for oxygen
enrichment. Periodic backwashing of the filter
bed flushes the precipitated iron to the drain
and readies the filter for use again. The dura-
tion of the backwash procedure will vary de-
pending on the iron concentration but gener-
ally is 10 minutes total. The frequency of
backwashing depends on iron concentration
and water usage and ranges from daily to
once every 10 days.
Before Starting Installation
Tools, Pipe, and Fittings, Other Materials
 Pliers
 Screwdriver
 Teflon tape
 Razor knife
 Two adjustable wrenches
 Additional tools may be required if modifi-
cation to home plumbing is required.
 Plastic inlet and outlet fittings are included
with the filter. To maintain full valve flow,
3/4” or 1” pipes to and from the filter fit-
tings are recommended. You should main-
tain the same, or larger, pipe size as the
water supply pipe, up to the softener inlet
and outlet.
 Use copper, brass, or PEX pipe and fittings.
 Some codes may also allow PVC plastic
pipe.
 ALWAYS install the included bypass valve,
or 3 shut-off valves. Bypass valves let you
turn off water to the filter for repairs if
needed, but still have water in the house
pipes.
 5/8” OD drain line is needed for the valve
drain. A 10’ length of hose is included.
with some models.
5

 Place the filter tank as close as possible to
the pressure tank (well system) or water
meter (city water).
 Place the filter tank as close as possible to
a floor drain, or other acceptable drain
point (laundry tub, sump, standpipe, etc.).
 Connect the filter to the main water supply
pipe BEFORE the water heater. DO NOT
RUN HOT WATER THROUGH THE FIL-
TER. Temperature of water passing
through the filter must be less than 100
deg. F.
 Do not install the filter in a place where it
could freeze. Damage caused by freez-
ing is not covered by the warranty.
 Put the filter in a place water damage is
least likely to occur if a leak develops. The
manufacturer will not repair or pay for wa-
ter damage.
 A 120 volt electric outlet, to plug the in-
cluded transformer into, is needed within 6
feet of the filter. The transformer has an
attached 6 foot power cable. Be sure the
electric outlet and transformer are in
an inside location, to protect from
wet weather.
 If installing in an outside location, you
must take the steps necessary to assure
the filter, installation plumbing, wiring,
etc., are as well protected from the ele-
ments, contamination, vandalism, etc., as
when installed indoors.
 Keep the filter out of direct sunlight.
The sun’s heat may soften and distort
plastic parts.
Where To Install The Filter
6

Sizing Requirements
Water Pressure
The water system must have a pump big enough to deliver the recommended backwash
rate with a minimum pressure at the inlet of the filter of 30 psi. If the existing system can-
not do this, it must be upgraded to do so. Whenever possible, the water system should be
adjusted to deliver at least 30 psi for even more satisfactory results.
Backwash Flow Rates
The most important criteria in sizing a filter is the capacity of the pump. The water must
pass through the filter media at the proper service flow rate. The filter must also be back-
washed at a flow rate sufficient to dislodge and remove the captured particles. Failure to
provide sufficient water will cause a build-up of particles in the filter media, impairing its
ability. In order for your filter to backwash and rinse properly, your pump must be capable
of providing the backwash flow rates indicated on page 4.
Check Your Pumping Rate
Two water system conditions must be checked carefully to avoid unsatisfactory operation or
equipment damage:
1. Minimum water pressure required at the filter tank inlet is 20 psi.
2. Measuring the pumping rate of your pump:
With the pressure tank full, draw water into a container of known volume, and measure the
number of gallons drawn until the pump starts again. This is draw-down. Divide this figure
by cycle time and multiply the result by 60 to arrive at the pumping rate in gallons per min-
ute (gpm). To aid in your calculation, insert the date in the following formula:
DRAW-DOWN ______ ÷ CYCLE TIME _______ x 60 = PUMPING RATE ________ (gals)
(secs.) (Gpm)
EXAMPLE: CYCLE TIME is 53 seconds. DRAW-DOWN is 6 gallons; then, PUMPING
RATE equals:
6 gallons ÷ 53 seconds x 60 = 6.8 gpm
See chart on page 4 for minimum flow rates.
NOTE: If your pumping rate is inadequate for the model, do not install your filter until
the problem has been corrected.
7

1. If your hot water tank is electric, turn off the power to it to avoid damage to the element
in the tank.
2. If you have a private well, turn the power off to the pump and then shut off the main wa-
ter shut off valve. If you have municipal water, simply shut off the main valve. Go to the
faucet, (preferably on the lowest floor of the house) turn on the cold water until all pres-
sure is relieved and the flow of water stops.
3. Locate the filter tank close to a drain where the system will be installed. The surface
should be clean and level.
4. Connect the inlet and outlet of the filter using appropriate fittings. Perform all plumbing
according to local plumbing codes.
 Use a ½” minimum pipe or tubing size for the drain line
 ON COPPER PLUMBING SYSTEMS BE SURE TO INSTALL A GROUNDING
WIRE BETWEEN THE INLET AND OUTLET PIPING TO MAINTAIN GROUND-
ING.
Any solder joints near the valve must be done before connecting any piping to the valve.
Always leave at least 6" (152 mm) between the valve and joints when soldering pipes that
are connected to the valve. Failure to do this could cause damage to the valve.
5. Connect the drain hose (10 ft included) to the valve and secure it with a hose clamp (also
included). Run the drain hose to the nearest laundry tub or drain pipe. This can be ran
up overhead or down along the floor. If running the drain line more than 20 ft overhead,
it is recommended to increase the hose size to 3/4”. NEVER MAKE A DIRECT CONNEC-
TION INTO A WASTE DRAIN. A PHYSICAL AIR GAP OF AT LEAST 1.5” SHOULD BE USED
TO AVOID BACTERIA AND WASTEWATER TRAVELLING BACK THROUGH THE DRAIN
LINE INTO THE FILTER.
6. Using the Allen Key (included), place the unit in the bypass position. Slowly turn on the
main water supply. At the nearest cold treated water tap nearby remove the faucet
screen, open the faucet and let water run a few minutes or until the system is free of any
air or foreign material resulting from the plumbing work.
7. Make sure there are no leaks in the plumbing system before proceeding. Close the water
tap when water runs clean.
8. Proceed to start up instructions.
Note: The unit is not ready for service until you complete the start-up instruc-
tions.
Installation Instructions
8

Filter Installation
9

10
System Start-Up
1. Plug the valve into an approved power source.
2. When power is supplied to the control, the screen will display “WAITING PLEASE” while it
finds the service position.
3. Start an Immediate Manual Regeneration. The valve will immediately start moving to the
BACKWASH position.
4. Open the inlet on the bypass valve slightly and very slowly allow water to enter the unit.
(If the water enters too quickly it will push the carbon up into the control valve and get
plugged).
5. Once the unit has filled sufficiently that water is at least equal to the height of the top of
the media shut down the water for 15 – 20 minutes for the carbon to soak. Unplug the
power cable. After the carbon has soaked for the recommended time continue by plug-
ging the power cable back in.
6. Turn the water back on slowly to backwash until water runs clear to drain.
7. Press any button to advance to the RINSE position. Check the drain line flow. Allow the
water to run for 3-4 minutes or until the water is clear.
8. The valve will automatically advance to the SERVICE position after the RINSE cycle is
complete. Open the outlet valve on the bypass, then open the nearest treated water fau-
cet and allow the water to run until clear, close the tap and replace the faucet screen.
9. Program time, date, and number of days between regenerations into controller using Pro-
gramming Instructions
Note : Carbon filters only:
Once the unit has filled sufficiently that water is at least equal to the height of the media
shut down the water for 15 – 20 minutes for the carbon to soak.
After the carbon has soaked for the recommended time continue with installation instruc-
tions.
Additional information for Non backwashing carbon filter.
After soaking, remove the aerator screen from the nearest faucet, run water at this faucet
until all fines (black) is gone from the water.
Start-up Instructions
Key Pad Configuration
SETTINGSThisfunctionistoenterthebasicsetupinformationrequiredatthe
timeofinstallation.
MANUALREGENThisbuttonhastwofunctions.Thefirstistoinitiateanimmediateor
delayedmanualregeneration.Thesecondiswhileinprogramming
mode,pressingthiskeyallowstheusertochangethevalueofeach
setting.
DOWN/UPIncreaseordecreasethevalueofthesettingswhileintheprogram‐
mingmode.

Programming Instructions
1. Press SETTINGS to enter programming. If the system has been inactive, you may
have to hold and press SETTINGS to unlock the display screen. Press UP or DOWN to
select which setting to modify.
2. To adjust a value, MANUAL REGEN. When the display flashes, the value may be
changed. Press UP or DOWN to change the value. Press MANUAL REGEN again to ac-
cept the value.
3. Press UP or DOWN to advance to the next option.
The table below can be used to help deter-
mine the frequency of regeneration for Multi-
Media and Taste & Odour filters. Use this ta-
ble as a guide since individual circumstances
will require more or less frequent regenera-
tions. This can be adjusted by the home
owner to suite their individual needs with fre-
quencies available from 1 – 99 days.
To prevent bacterial build up in the media,
activated carbon filters should not exceed 6
days between backwashes.
Backwash Frequency
Menu‐Level1
PressSETTINGSkey
TIME
12:00 AM
REG.TIME
12:00 AM
DAYS
3
Example
Page1STAR
PLUMBing
Page2TEL(552)
764 ‐1234
Sediment Mild Average Extreme
Taste Odor Mild Average Extreme
No. Of Per-
sons Days Between Back Wash (Regenerations)
26666666666444444
36666444444333333
46666444333222222
56644333322221111
66644333222211111
76443322211111111
86443222211111111
94433221111111111
10 4332211111111111
11

About The System
Manual Regeneration (Step / Cycle Valve)
If screen is locked, press and hold SETTINGS for 3 seconds to unlock. To initiate an imme-
diate regeneration, press and hold the MANUAL REGEN key for 5 seconds. The valve will
immediately start into manual regeneration.
To initiate a delayed regeneration, press the MANUAL REGEN key once to turn on and a re-
generation will be queued at the next pre-set regeneration time (i.e. 2:00 a.m.).. To cancel,
press the MANUAL REGEN key again.
Operation During A Power Failure
In the event of a power failure, the valve will keep track of the time and day for 48 hours.
The programmed settings are stored in a non-volatile memory and will not be lost during a
power failure. If power fails while the unit is in regeneration, the valve will finish regenera-
tion from the point it is at once power is restored. If the valve misses a scheduled regen-
eration due to a power failure, it will queue a regeneration at the next regeneration time
once power is restored.
12

Automatic Raw Water Bypass During Regeneration
The regeneration cycle can last 30 minutes after which filtered water service will be re-
stored. During regeneration, un-filtered water is automatically bypassed for use in the
household. Hot water should be used as little as possible during this time to prevent un-
filtered water from filling the water heater. This is why automatic regeneration is set for
sometime during the night and manual regenerations should be performed when little or no
water will be used in the household.
Normal regeneration time is 12:00 AM.
New Sounds
You may notice new sounds as your filter operates. The regeneration cycle lasts up to 30
minutes. During this time, you may hear water running intermittently to the drain.
Manual Bypass
In the case of emergency you can isolate your water filter from the water supply using the
bypass valve located at the back of the control. In normal operation the bypass is open with
the on/off knobs in line with the inlet and outlet pipes.
To isolate the filter, simply rotate the knobs counter clockwise (as indicated by the word BY-
PASS and arrow) until they lock. You can use your water related fixtures and appliances as
the water supply is bypassing the filter. However, the water you use will be hard. To resume
water service, open bypass valve by rotating the knobs counterclockwise.
System Configuration
TankSize(Diameter) DrainLineFlow
Control(DLFC)
8" #5(3.5GPM)
9" #A(5.0GPM)
10" #A(5.0GPM)
12" #B(7.0GPM)
14" #C(10.0GPM)
16" none
SuggestedFilterValveConfiguration
13

Maintenance
Care of Your System
To retain the attractive appearance of your new water filter, clean occasionally with mild
soap solution. Do not use abrasive cleaners, ammonia or solvents. Never subject your sof-
tener to freezing or to temperatures above 100°F.
Maintenance of your new water filter requires very little time or effort but it is essential.
Regular maintenance will ensure many years of efficient and trouble-free operation.
1. Periodically make sure your pump is performing satisfactorily to ensure sufficient water is
available for backwashing the filter.
2. Periodically test your raw and filtered water to ensure conditions are still the same for
your original settings and that the unit is working they way it is intended to. Water test-
ing is often the best way to determine when the filter media will require replacement.
3. Periodically check that the drain line is clear and free from any obstructions.
NE - Neutralizing Filter - the media bed in a neutralizing filter is slowly dissolved and has
to be replaced. The frequency of replacement varies, depending on water quality - consult
your dealer to determine the expected life of your media bed.
AC - Taste and Odor Filter - under normal operating conditions the effective life of the
filter media is approximately one to three years, depending on the water quality, after
which, taste and odor problems may return. When this happens, contact your dealer for a
replacement media bed.
MM - Sediment and Turbidity Filter - under normal operating conditions, the media
should never need to be replaced. However, if you experience pressure loss and cannot cor-
rect it with a manual regeneration, your media bed may need replacing - contact your
dealer.
Replacing the Media Bed
Check to ensure all media parts are received.
The first step in replacing the media bed is to shut off the water supply to the filter. Then
place the unit into the backwash position to release any pressure in the lines. At this point,
you must disconnect the plumbing from the inlet and outlet. Then unscrew the control
valve from the fibreglass tank. Once this has been done, remove the distributor tube. Then
you can remove the filter media and two types of gravel from the tank. The quickest way to
do this is by simply tipping the tank upside down into a large drum or pail. The tank must
be rinsed out completely and have no media or gravel left in it at all.
Installation & Replacement Filter Media Pak
14

Loading the Media Pak
Place the distributor tube back down the center of the tank. NOTE: the top of this tube
should be plugged with a rag or cork to prevent media from entering. Pour the bag of
coarse gravel into the tank, and then pour the bag of fine gravel into the tank.
It is important that the distributor tube is not moved or pulled out as it is not possible to put
it down to the bottom of the tank once gravel or media are in the tank.
Finally pour the larger bag(s) of media into the tank in the following order:
Multimedia Filters
1. Coarse gravel (1/2 x 1/4) 4. Fine garnet (30 x 40)
2. Fine gravel (1/8 x 1/16) 5. Fine filter sand (.45 x .55)
3. Coarse gravel (8 x 12) 6. Anthrafilt
ACF Carbon Filters Neutralizing Filters
1. Coarse gravel 1. Coarse gravel 4. Mag Oxide
2. Fine gravel 2. Fine gravel
3. Carbon 3. Calcite
Once this is done, the rag or cork should be removed from the distributor tube. Clean off
the top of the tank. Finally place the control valve on the tank and on to the distributor
tube. Tighten the control valve on to the tank. Connect or reconnect the inlet and outlet and
drain. The control valve should be in the backwash position. Slowly open the inlet valve wa-
ter supply and slowly fill the filter tank until water appears at the open drain line. Return the
control to the service position and shut the inlet off for approximately one hour to allow the
media to soak in the water.
After one hour, turn inlet water on slowly and place the control into the backwash position
and plug the unit’s electrical cord into a constant power source. Let the unit continue
through its regeneration cycle automatically. The regeneration is necessary so all media
fines are backwashed down the drain to ensure clean filtered water.
15

Main Repair Parts
Replacement Part Number Part Description DWG # Quantity
60010052 POWER TRANSFORMER 120V-12V
A1
60010002 BYPASS / METER
B1
10010063 485 UP DOWN FLOW FILTER VALVE
C1
60010048 TOP CONE
D1
25020041 844 TANK (75)
E1
25020042 948 TANK (100)
E1
25020043 1054 TANK (150)
E1
25010058 1252 TANK (200)
E1
25030007 1465 TANK (300)
E1
50010005 DISTRIBUTOR 1X54
F1
REPLACEMENT PARTS - FILTE
R
Replacing Drain Line Flow Control (DLFC)
1. Remove the red clip that secures the drain line elbow.
2. Remove the BLFC washer from the elbow fitting.
3. Reassemble using the reverse procedure.
16

17

A A A
B
D
F
E
A
C
Replacement Part Number Part Description DWG # Quantity
60010020 3/4" NPT ELBOW
A2
60010019 1" NPT STRAIGHT A2
60010023 3/4" NPT STRAIGHT
A2
60010079 VALVE COUPLING INLET
B1
60010101 VALVE COUPLING OUTLET (METER SIDE)
C1
60010025 PLASTIC SECURE CLIP D2
60010046 BYPASS SS CLIP E2
60010047 BYPASS SS SCREW F 2
REPLACEMENT PARTS - CONNECTORS
Main Repair Parts - Connectors
18

Control Valve Exploded View
Control Valve Exploded View
19

Control Valve Parts List
Item No. Part No. Part Discription Quantity
A01 05056087 Screw-M5×12(Hexagon) 3
A02 05056088 Screw-M5×16(Hexagon with Washer) 2
A03 05056047 End Plug Retainer 1
A04 05010081 Bnt65 Piston Rod 1
A05 05056097 Piston Pin 1
A06 05056023 End Plug 1
A07 05056070 Quad Ring 2
A08 05056024 End Plug Washer 1
A09 05056022 Piston Retainer 1
A10 05056181 Piston (Electrical) 1
A11 05056104 Muffler 1
A12 05056021 Spacer 4
A13 05056073 Seal 5
A14 05056019 Bnt65 Valve Body 1
A15 05056063 O-ring-φ78.74×5.33 1
A16 05056129 O-ring-φ23×3 4
A17 05056025 Adaptor Coupling 2
A18 05056044 Adaptor Clip 2
A19 05056090 Screw-ST4.2×13(Hexagon with Washer) 2
A20 21709003 Secure Clip 2
A21 05056140 Valve Connector 1
A22 05056065 O-ring-φ23.6×2.65 2
A23 21319006 Screw Adaptor 2
A24 26010103 O-ring-φ25×3.55 1
A25 07060007 Valve Bottom Connector 1
A26 13000426 Screw-ST2.9×13(Large Wafer)  2
A27 05056038 Drain Fitting 1
A28 26010003 O-Ring-φ18×2.65 1
A29 05056036 DLFC Button Retainer 1
A30 05056079 O-Ring-φ15×0.8 1
A31 05056143 DLFC-2# 1
A32 05056035 BLFC Button Retainer 1
A33 05056191 BLFC-2# 1
A34 05056138 O-Ring-φ14×1.8 1
A35 05056100B BLFC Fitting 1
A36 05056106 Brine Line Screen 1
A37 05056107 BLFC Tube Insert 1
A38 05056033 BLFC Ferrule 1
A39 05056108 BLFC Fitting Nut 1
A40 05056086 Screw-M5×30(Hexagon with Washer) 2
A41 05056029 Injector Cover 1
20