Hyena LED Multi User manual

This guideline is applicable for the Hyena e-bike system only
LED Multi
Product Manual
Version 210218
Copyright © 2021 HYENA INC. All Right Reserved.
This manual is intended primarily for the trained technician to install, disassemble, or maintain the e-bike.

Content
Product features 1
Product Description 1
Parts Description 1
Product Dimension 2
Cable Pin Definition 2
Technical Data 3
Function 3
Characteristic 3
Mounting Parameter 3
Connection 3
LED Indication Information 4
Certification 4
Mounting 5
Tool List 5
Accessory List 5
Mounting Instructions 5
Operation 6
Operation Instructions 6
Safety Instructions 8
Important Notice 8
Moving and Storage Instructions 8
Maintenance 8
Disposal 8

HYENA E-BIKE SYSTEMS
1
Product features
Product Description
The Hyena LED Multi features compact size, 3 multi-color LED indicators, flexible mounting position on handlebars (both
left and right-hand side). Supports app and service tool connection via Bluetooth.
Parts Description
A Up & Increase support level button
B Support level indicator
C Down & Decrease support level button
D Fastening screw
F Battery status indicator
G Bluetooth / error indicator
H Cable
I Rubber ring
E Power on/off button

HYENA E-BIKE SYSTEMS
2
Product Dimension
Cable Pin Definition
*1. refer to page 3 [Mounting Parameter]

HYENA E-BIKE SYSTEMS
3
Technical Data
Function
Number of button
3
Power/Up/Down
Turn on/off system
Power button
Switch motor support level
UP/Down button
Turn on/off light
Long press Up button
Walk-assist
Long press Down button
Connection
Bluetooth/Hyena 6P
CM-WP408-06M
Battery wake up function
Yes
HMI/DEN
Characteristic
Protocol
CAN
Support Hyena CAN
Operating voltage
10~14V
Operating temperature
-10℃~+60℃80%RH
Storage temperature
-20℃~+70℃80%RH
Waterproof level
IPX5
Quiescent current
<1mA
Measure condition
a. System off
b. Battery, Console, Display, Driver, Motor
and Sensor are connected well.
c. Remove all smart parts.
Mounting Parameter
Dimension (mm)
L48, W40, H51 mm
Mounting position
Left/Right handle bar
Clamp diameter
22.2 mm
Cable length
520 mm (standard)
250 mm available (*1)
Standard connector
Hyena 6P male
CM-WP408-06M
Connection
Bluetooth connection
Bluetooth 4.2 BLE
Support to HRA (Hyena Rider Assistant )
& HST (Hyena Service Tool)

HYENA E-BIKE SYSTEMS
4
LED Indicator Information
Riding support level
0~3
Battery status
4 segments
Certification
EN15194:2017
Yes
CE
Yes
BQB
Yes
Bluetooth
RoHS 2.0
Yes

HYENA E-BIKE SYSTEMS
5
Mounting
Tool List
Hexagon key M3
Disc hex bolts
Accessory List
Hex socket head cap screw
M3x0.5Px12mm
1 pcs
Rubber ring
1 pcs
Mounting Instructions
• Use the proper tools during the installation or removal process.
• Fasten the hex bolt with 1 Nm torque value.
• Carefully install is necessary, do not strike it with any tool such as a hammer or wrenches.
Step1: Insert the rubber ring.
Step2: Mount the HMI hook
on the rubber ring
Step3: Fasten the hex bolt.

HYENA E-BIKE SYSTEMS
6
< 0.5 sec
ON
> 2 secs
OFF
> 2 secs
e-System Operation
Caution - The e-Bike system can only be activated when
the following requirements are met:
-A sufficiently charged battery is attached.
-The e-system is connected properly.
Operation Instructions
Turn on/off the e-bike system
Long press the power button to turn on/off.
Note
-Always switch off the e-Bike system when you park the
e-Bike or before removing the battery.
Turn on/off light
Long press up button to turn on/off light.
When e-bike equipped with front/rear lights.
Support level adjusting
Short press up/down button to adjust the riding support
level while you pedaling.
-Default on Off mode.
-Press up/down button to adjust.
-None circulation.
-Automatic memory previous setting.
Note
-The system is activated as soon as you start pedaling.
-The e-Bike drive output only supports a speed below
25/45 km/h, as soon as you have reached 25/45 km/h,
e-system switches off the assistance, then automatically
reactivated when your speed is below 25/45 km/h.
Off Mode
White Light
Mode 1
Green Light
Mode 3
Red Light
Mode 2
Yellow Light

HYENA E-BIKE SYSTEMS
7
> 2 secs to active
Green light flashing
while walk assist
mode activated.
Walk assist mode
Long press on down button for 2 seconds to active the
walk assist mode. When the walk assist mode activated,
the support level indicator will keep flashing in green.
- Long Press UP Button start the walk assist. As long as
you are holding the UP button, your e-bike will be
propelled forward at a slow speed.
- Release the UP button to stop pushing your e-bike.
- At the walk assist mode, if the UP button isn’t
pressed > 5 secs or the DOWN button isn’t pressed <
0.5 sec, the walk assist mode will automatically turn
off for safety
Note
The walk assistance function must only be used when
pushing the e-Bike. Make sure you are ready and stand
steady before activating the walk assistance.
Do not activate the walk assistance when you ride on the
e-bike or if the wheels are not in contact with the ground
Bluetooth connection
Blue lights flash 3 times when Bluetooth connected or
disconnected.
Battery indicator
The indicator shows the battery status.
Error alert
Red lights flash when a system error is detected.
76-100%
Green light
51-75%
Blue light
26-50%
Yellow light
1-25%
Red light
Red light keeps flashing
when capacity under 9%
10 seconds
Flash
3 seconds
Loop
Error
Alert
General
Mode

HYENA E-BIKE SYSTEMS
8
Safety Instructions
Instructions Pertaining To A Risk Of Fire,
Electric Shock, Or Injury To Persons
• WARNING - When using the LED Multi, basic
precautions should always be followed, including the
following:
• Read all the instructions before using the product.
• To reduce the risk of injury, close supervision is
necessary when the product is used near children.
• Do not use this product if the flexible power cord or
output cable is frayed, has broken insulation, or any other
signs of damage.
• All the component charging terminal and leads shall use
original Hyena components.
• This equipment is not intended to be used at ambient
temperatures less than -20°C(4°F) or above ambient
temperatures of 60°C(140°F).
• Do not immerse the product or any e-system component
in water.
• Do not place the product or any e-system component
near fire or heat.
• Always turn off the e-bike system and remove the battery
before install, disassemble or modify any components on
the e-bike.
Important Notice
• This user manual is intended primarily for the trained
technician to install, disassemble or maintain the e-bike.
• Users who are not professionally trained for bicycle
assembly should not attempt to install, disassemble or
modify the components themselves.
• All Hyena e-system manuals and technical documents
are accessible online at "www.hyena-ebike.com".
• The term “battery” is used in these instructions to mean
all original Hyena e-Bike batteries.
• Read and observe the safety warnings and directions
contained in all the Hyena e-Bike system operating
instructions and in the operating instructions of your e-
Bike.
Moving and Storage Instructions
• When possible keep the product and all e-system
components in their original package and keep tools or
other metal objects away from them while storage and
moving.
• If you did not keep the original packaging, they can be
packed in strong cartons with proper packing materials
such as bubble wrap or soft cloth, and label the cartons
Fragile.
• Do not store the product at ambient temperatures less
than -20°C(-4°F) or above ambient temperatures of
70°C(158°F).
• Cover the product to prevent damage by sunlight if you
will be keeping it stored at any place for more than a
week.
• Store the product on a fireproof surface and without
contact water, heat, or sands.
• Do not place any heavy item on the product or any e-
system component.
• Do not place the product or any e-system component in
the car trunk for more than one day.
• Do not load or move the product in the rain whenever
possible, and make sure it has no moisture or mildew
before loading it.
• Do not drop the product from more than 30cm height.
Maintenance
• Do not clean the product or any e-system component
with any detergent or organic solvent. Only clean the
product with a water-dampened soft cloth.
• Do not clean the product or any e-system component
with pressured water.
Disposal
• In accordance with Directive 2012/19/EU, electronic
devices that are no longer usable and defective/drained
batteries must be collected separately and recycled in an
environmentally friendly manner.
• The e-system drive unit including the motor, driver,
battery, speed sensor, HMI, accessories, and packaging
should be disposed of in an environmentally correct
manner.
• Do not dispose of e-bikes and their components with
household waste.
SAVE THESE INSTRUCTIONS
This symbol is only valid within the European
Union. Follow local regulations when disposing
of used batteries. If you are not sure, consult
the place of purchase or a bicycle dealer