hygena Vince Ottoman Bed Frame User manual

Vince Ottoman Bed Frame
Assembly Instructions - Please keep for future reference
330/7281
355/4845
Important – Please read these instructions fully before starting assembly
Issue 1 - 01/12/14
ehtllac,strapgnissimrodegamadevahroplehdeenuoyfI Customer Helpline:
Argos = 0345 6400800
Dimensions
Depth x Width x Height
213cm x 148cm x 111cm (Double)
223cm x 163cm x 111cm (King)

1
Safety and Care Advice
Important – Please read these instructions fully before starting assembly
• Check you have all the
components and tools listed on
the following pages.
• Remove all fittings from the
plastic bags and separate them
into their groups.
• Keep children and animals
away from the work area, small
parts could choke if swallowed.
• Make sure you have enough
space to layout the parts before
starting.
• Assemble the item as close
to its final position (in the same
room) as possible.
• Assemble on a soft level
surface to avoid damaging the
unit or your floor.
• Assembly requires 2 people.
• To reduce
the likelihood of
damaging your
product please
ensure that your
power drill is set on a low torque
setting.
• Only clean using a damp cloth
and mild detergent, do no use
bleach or abrasive cleaners.
• From time to time check that
there are no loose screws on
this unit.
• This product should not be
discarded with household waste.
Take to your local authority
waste disposal centre.
Care and maintenance
• Please ensure children and
pets do not play in the storage
area or try to lift up the metal
frame.
• Once assembled, put mattress
on frame before pushing it down
and only lift up or push down the
metal frame with mattress on top.
Caution
• Do not fully tighten bolts until
the whole bed is assembled.
• Do not overtighten the nuts to
avoid causing damage to the
threads.
• Only use the handle to lift
and lower the bed frame to
avoid trapping fingers.
• Recommended thickness of
mattress:16-22cm.

Components - Panels
Please check you have all the panels listed below
2
Middle bar
9
Headboard
1
Left side bar
5
Front bar
7
Bottom support bar
10
Right side rail
2
If you have damaged or missing components, call the
Customer Helpline: Argos = 0345 6400800
Left side rail
3
Footboard
4
Right side bar
6
Rear bar
8
Slat x 26 (double)
11
Strap
12
Piston x 2
13
Non-woven fabric
Mattress stopper x 2
15
Corner bracket x 4
16
14
Leg
17
Slat cap x 13 (Double)
18
Slat cap x 26 (Double)
19
or x 30 (King)
or x 15 (King) or x 30 (King)
(in the headboard storage) (2 pcs for headboard)
(2 pcs for footboard)

3
Please check you have all the fittings listed below
12mm Bolt x 4
Ruler - Use this ruler to help correctly identify the screws
A
29MM Bolt x 12
E
19mm Bolt x 8
B
I
19mm Bolt x 16
C
Nut x 4
Note: The quantities below are the correct amount to complete the assembly. In some cases more fittings
may be supplied than are required.
100 20 30 40 50 60 70 80 90 100
0 5 10 15 20 25 30 35 40 45 50 55 60 65 70 75 80 85 90 95 100 110 115 120 125 130 135 140 145 150 155 160 165 170
105
34mm Bolt x 4
FD
44mm Bolt x 9
H
Hex key x 1
Components - Fittings
G
Plain washer x 4
J
Wrench x 1
Tools required
Phillips screwdriver
The bolts length is measured from the head to the point (19mm bolt sho wn
).

4
Assembly Instructions
Step 1
Assemble slat frame
using bolts .
7
B
8
5
6
9
F
F
B
B
a: Fix side bars & ,
to front bar and rear
bar using bolts .
15
56
7
8F
Fix middle bar to front
bar and rear bar
using bolts
9
78
b: Fix mattress stoppers
onto front bar
15
7
7
A
A
A
b:
a:
Note: Make sure the
arrows on side bars &
middle bar are pointed
to the front bar.

Step 2
5
Assembly Instructions
Step 3
& to
23
Fix side rails
headboard and
footboard using bolts
.
2
3
1
4
1
4
D
D
D
D
ABC
Fix bottom support bar
to side rails using
bolts .
10
10
E
E
E
Follow step A-B-C.
Do not fully tighten
bolts at this stage.
Important note:

Step 4
6
Assembly Instructions
Step 5
Place the assembled unit
as shown.
Fix pistons to the
lifting mechanism using
nuts .
13
13
Fix corner brackets
to headboard and side
rails using bolts as
shown.
HH
H
Note: Make sure the
the pistons are placed
as the figure shown.
C
a:
16
a:
16
C
C
C
C
Continued on next page.
Make sure the side
with label faces top.
Important note:

Step 5 - continued
7
Assembly Instructions
Step 6
Attach non-woven fabric
on the bottom of the
bed as shown.
14
14
Fix corner brackets
to footboard and side
rails using bolts as
shown.
C
b:
16
b:
C
C
C
C
16
Important note: After all the parts are positioned, you
can now fully tighten all bolts fixed on previous steps.
Make sure the side
with label faces top.
Important note:

Step 7
8
Assembly Instructions
a: Push the slat frame
a:
down.
Step 8
Fix the assembled slat
frame onto the lifting
mechanism using plain
washers and bolts .
F
G
B
17
17
Fix leg under the
millde bar using bolt .
F
GB
B
G
Continued on next page.

Step 8 - continued
9
Assembly Instructions
Tie the strap to the
end of the middle bar
as shown.
12
12
Assembly is complete.
Step 9
19
b: Slot the slats to
b:
11
the slat caps &
then insert it to the slat
frame
18
18
19
11
11
11