hygena Tall boy 528/9060 Datasheet

Dimensions
Width - 24cm
Depth - 28cm
Height - 164cm
Issue 1 - 21/03/16
Important– Please read these instructions fully before starting assembly
Assembly lnstructions - please keep for future reference
Hygena- Tall boy
538/8734
528/9060

WARNING
In order to help prevent overturning –
To help prevent product toppling over please follow the below steps:-
Do not allow children to climb or hang on the furniture
Do not place heavy items in the top drawers
Do not place heavy items on top of the furniture, unless the furniture has been
designed for this purpose
You will need to provide wall plugs and screws applicable for your wall type

Components - Panels
Please check you have all the panels listed below
2
If you have damaged or missing components, call the
Customer Helpline:
1234
10 11
56
12
789
13 14

If you have damaged or missing components, call the
Customer Helpline:
Components - Fittings
Please check you have all the fittings listed below
Note: The quantities below are the correct amount to complete the assembly.In some cases more fittings
may be supplied than are required.
7mm Suitable drill bit
(for use with wall plug)
Small
hammer
Ruler - Use this ruler to help correctly identify the screws
0
The screws length is measured from the head to the point (30mm screw shown).
5 10 15 20 25 30 35 40 45 50 55 60 65 70 75 80 85 90 95 100 105 110 115 120 125 130 135 140 145 150 155 160 165 170
Wall strap x 1 4x32mm Screw x 2
Plug x1 Panel Stiffenersx 8 Shelf support x
6x50mm Screw x 4 Hex key x 1

Assembly lnstructions
Step 1
5
Fitting Male camlock
1.Insert 9 x male camlocks
to the top 5 , bottom left side
8 and bottom right side 10
and bottom front bar 7 .
B
5
7
8
10
B
B

Assembly lnstructions
Step 2
6
9
Fitting dowels
1.Glue and insert 12 x
dowels to upper left side
2 ,upper right side 3 ,
bottom 6 & middle front bar
9 , bottom left side 8 and
bottom right side 10 .
6
2
3
8
10
7

Assembly lnstructions
7
2
3
1
3
2
4
Step 3
Step 4
1.Attach fixed shelf 1 to
upper right side 3 & upper
left side 2 with 4 x screws
using Hex key
supplied to tighten.
1.Slide upper back 4 along
grooves in upper left side 2
and upper right side 3 .
MN
N
M

Step 5
Assembly lnstructions
8
Step 6
Attaching panels
1.Attach bottom front bar 7
to bottom 6 .
2.Insert 1 x female camlock
to bottom 6 .
Use a screwdriver to turn the
female camlock clockwise to
lock.
C
D
7
1.Attach top 5 to upper left
side 2 & upper right side
3 .
2.Insert 4 x female camlocks
to upper left side 2 &
upper right side 3 .
Use a screwdriver to turn the
female camlock clockwise to
lock.
3
2
5
C
C

Assembly lnstructions
Step 7
Step 8
1.Attach upper right side 10
to bottom 6 & middle front
bar 9 .
2.Insert 2 x female camlocks
to bottom 6 .
Use a screwdriver to turn the
female camlock clockwise to
lock.
D
6
8
9
C
D
8
10
9
1.Attach bottom 6 & middle
front bar 9 to bottom left
side 8 .
2.Insert 2 x female camlocks
to bottom 6 .
Use a screwdriver to turn the
female camlock clockwise to
lock.
9
C
C
6
C

Step 9
Assembly lnstructions
10
Step 10
11
1
3
2
1.Slide bottom back 11
along grooves of the unit as
shown in diagram
1.Insert 4 x male camlocks
to the fixed shelf 1 .
B
8
10
B

Step 11
Assembly lnstructions
11
D
H
H
G
G
Step 12
13
2
8
10
9
1.Attach the upper section to
the bottom section by locating
Male camlocks in panel 1
into adjacent holes in panels
8 and 10 .
2.Insert 4 x female camlocks
to bottom left side 8
and bottom right side 10 .
Use a screwdriver to turn the
female camlock clockwise to
lock.Please refer to the
"Using Camlocks"
section at the front of this
instruction for further
assistance.
1.Attach 2 x hinges to
the upper door 12 with 4 x
screws as shown.
2.Attach 2 x hinges to
the bottom door 13 with 4 x
screws as shown.
12
13
C
H
H
G
G

Step 13
Assembly lnstructions
10
L
H
a: b: c:
Hinge adjustment:
a: To move the doors up
or down, loosen screws
shown and move doors
to suit
b: To move the doors in
or out, loosen screws
shown and move doors
to suit.
Retighten screws
c: To move the doors left
or right, adjust screws
shown.
1. Attach upper door 12
and bottom door 13 to the
unit with 8 x screws as
shown.
2.Use 8 x stickers to
cover camlock hole on upper
left side 2 and upper right
side 3 , bottom left side 8
and bottom right side 10 .
12
13
12
5
2
3
10
8
L
H

Step 14
Assembly lnstructions
14
14
14
14
14
1.Insert shelf supports
into the holes inside the unit
in the desired position
2.Place adjustable shelves
14 on the shelf supports.
13
K
K

Step 15
Assembly lnstructions
14
1.Insert 8 x panel Stiffeners
into the back panel grooves
as shown .These add support
and give the unit rigidity.
2.Using screw & washer
secure the 1 x nylon strap
to the back of top

Step 16
Assembly lnstructions
15
WALL
If you need help or have damaged or missing parts, call the Customer Helpline: 0345 6400800
Argos LTD. 489-499 Avebury boulevard, Central Milton Keynes, MK9 2NW